54AC153

54AC153 TI1 | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

54AC153,54ACT153 54AC153 54ACT153 Dual 4-Input Multiplexer Literature Number: SNOS088

54AC153 • 54ACT153 Dual 4-Input Multiplexer General Description The ’AC/’ACT153 is a high-speed dual 4-input multiplexer with common select inputs and individual enable inputs for each section. It can select two lines of data from four sources. The two buffered outputs present data in the true (non-inverted) form. In addition to multiplexer operation, the ’AC/’ACT153 can act as a function generator and generate any two functions of three variables.

Features

n ICC reduced by 50% n Outputs source/sink 24 mA n ’ACT153 has TTL-compatible inputs n Standard Microcircuit Drawings (SMD) — ’AC153: 5962-87625 — ’ACT153: 5962-87698 Logic Symbols Pin Names

Description

I0a–I3a Side A Data Inputs I0b–I3b Side B Data Inputs S0,S 1 Common Select Inputs Ea Side A Enable Input Eb Side B Enable Input Za Side A Output Zb Side B Output FACT ® is a registered trademark of Fairchild Semiconductor Corporation. DS100271-1 IEEE/IEC DS100271-2 September 1998 54AC153•54ACT153 Dual 4-Input Multiplexer © 1998 National Semiconductor Corporation DS100271 www.national.com

The ’AC/’ACT153 is a dual 4-input multiplexer. It can select two bits of data from up to four sources under the control of the common Select inputs (S 0,S 1). The two 4-input multi- plexer circuits have individual active-LOW Enables (Ea,E b) which can be used to strobe the outputs indepedently. When the Enables (E a,E b) are HIGH, the corresponding outputs Za,Zb) are forced LOW. The ’AC/’ACT153 is the logic imple- mentation of a 2-pole, 4-position switch, where the position of the switch is determined by the logic levels supplied to the Select inputs. The logic equations for the outputs are shown below. Z a = Ea • (I0a • S1 • S0 +I1a • S1 • S0 + I2a • S1 • S0 +I3a • S1 • S0) Zb = Eb • (I0b • S1 • S0 +I1b • S1 • S0 + I2b • S1 • S0 +I3b • S1 • S0) Truth Table Select Inputs (a or b) Output Inputs S0 S1 E I0 I1 I2 I3 Z XX H XXXX L L LLL X X X L LL L HXXX H HL L XLXX L HL L XHXX H LH L XXLX L LH L XXHX H HH L XXXL L HH L XXXH H H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Pin Assignment for DIP and Flatpak DS100271-3 Pin Assignment for LCC DS100271-4 www.national.com 2

Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.national.com3

Absolute Maximum Ratings(Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V CC ) −0.5V to +7.0V DC Input Diode Current (IIK) VI = −0.5V −20 mA VI = VCC + 0.5V +20 mA DC Input Voltage (VI) −0.5V to V CC + 0.5V DC Output Diode Current (IOK ) VO = −0.5V −20 mA VO = VCC + 0.5V +20 mA DC Output Voltage (VO ) −0.5V to V CC + 0.5V DC Output Source or Sink Current (IO ) ±50 mA DC V CC or Ground Current per Output Pin (ICC or IGND ) ±50 mA Storage Temperature (TSTG ) −65˚C to +150˚C Junction Temperature (TJ) CDIP 175˚C Recommended Operating Conditions Supply Voltage (VCC ) ’AC 2.0V to 6.0V ’ACT 4.5V to 5.5V Input Voltage (V I) 0 Vt oV CC Output Voltage (VO ) 0 Vt oV CC Operating Temperature (TA) 54AC/ACT −55˚C to +125˚C Minimum Input Edge Rate (ΔV/Δt) ’AC Devices V IN from 30% to 70% of VCC VCC @ 3.3V, 4.5V, 5.5V 125 mV/ns Minimum Input Edge Rate (ΔV/Δt) ’ACT Devices V IN from 0.8V to 2.0V VCC @ 4.5V, 5.5V 125 mV/ns Note 1:Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recom- mend operation of FACT ® circuits outside databook specifications. DC Characteristics for ’AC Family Devices 54AC Symbol Parameter V CC TA = Units Conditions (V) −55˚C to +125˚C Guaranteed Limits VIH Minimum High Level 3.0 2.1 V OUT = 0.1V Input Voltage 4.5 3.15 V or V CC − 0.1V 5.5 3.85 VIL Maximum Low Level 3.0 0.9 V OUT = 0.1V Input Voltage 4.5 1.35 V or V CC − 0.1V 5.5 1.65 VOH Minimum High Level 3.0 2.9 I OUT = −50 µA Output Voltage 4.5 4.4 V 5.5 5.4 (Note 2) VIN = VIL or VIH 3.0 2.4 I OH = −12 mA 4.5 3.7 V I OH = −24 mA 5.5 4.7 I OH = −24 mA VOL Maximum Low Level 3.0 0.1 I OUT = 50 µA Output Voltage 4.5 0.1 V 5.5 0.1 (Note 2) VIN = VIL or VIH 3.0 0.50 I OL = 12 mA 4.5 0.50 V I OL = 24 mA 5.5 0.50 I OL = 24 mA IIN Maximum Input 5.5 ±1.0 µA V I = VCC , GND Leakage Current IOLD Minimum Dynamic Output Current (Note 3) 5.5 50 mA V OLD = 1.65V Max IOHD 5.5 −50 mA V OHD = 3.85V Min www.national.com 4

DC Characteristics for ’AC Family Devices(Continued) 54AC Symbol Parameter V CC TA = Units Conditions (V) −55˚C to +125˚C Guaranteed Limits ICC Maximum Quiescent 5.5 80.0 µA V IN = VCC Supply Current or GND Note 2:All outputs loaded; thresholds on input associated with output under test. Note 3:Maximum test duration 2.0 ms, one output loaded at a time. Note 4:IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit@ 5.5V VCC . ICC for 54AC@ 25˚C is identical to 74AC@ 25˚C. DC Characteristics for ’ACT Family Devices 54ACT Symbol Parameter V CC TA = Units Conditions (V) −55˚C to +125˚C Guaranteed Limits VIH Minimum High Level 4.5 2.0 V V OUT = 0.1V Input Voltage 5.5 2.0 or V CC − 0.1V VIL Maximum Low Level 4.5 0.8 V V OUT = 0.1V Input Voltage 5.5 0.8 or V CC − 0.1V VOH Minimum High Level 4.5 4.4 V I OUT = −50 µA Output Voltage 5.5 5.4 (Note 5) VIN = VIL or VIH 4.5 3.70 V I OH = −24 mA 5.5 4.70 I OH = −24 mA VOL Maximum Low Level 4.5 0.1 V I OUT = 50 µA Output Voltage 5.5 0.1 (Note 5) VIN = VIL or VIH 4.5 0.50 V I OL = 24 mA 5.5 0.50 I OL = 24 mA IIN Maximum Input 5.5 ±1.0 µA V I = VCC , GND Leakage Current ICCT Maximum 5.5 1.6 mA V I = VCC − 2.1V ICC /Input IOLD Minimum Dynamic 5.5 50 mA V OLD = 1.65V Max IOHD Output Current (Note 6) 5.5 −50 mA V OHD = 3.85V Min ICC Maximum Quiescent 5.5 80.0 µA V IN = VCC Supply Current or GND Note 5:All outputs loaded; thresholds on input associated with output under test. Note 6:Maximum test duration 2.0 ms, one output loaded at a time. Note 7:ICC for 54ACT@ 25˚C is identical to 74ACT@ 25˚C. www.national.com5

VCC TA = −55˚C Symbol Parameter (V) to +125˚C Units (Note 8) C L = 50 pF Min Max tPLH Propagation Delay 3.3 1.0 19.5 ns S n to Zn 5.0 1.0 14.0 tPHL Propagation Delay 3.3 1.0 18.0 ns S n to Zn 5.0 1.0 13.5 tPLH Propagation Delay 3.3 1.0 16.5 ns Et oZ n 5.0 1.0 12.5 tPHL Propagation Delay 3.3 1.0 14.0 ns Et oZ n 5.0 1.0 10.0 tPLH Propagation Delay 3.3 1.0 16.0 ns I n to Zn 5.0 1.0 11.5 tPHL Propagation Delay 3.3 1.0 14.5 ns I n to Zn 5.0 1.0 10.5 Note 8:Voltage Range 3.3 is 3.3V±0.3V Voltage Range 5.0 is 5.0V±0.5V 54ACT VCC TA = −55˚C Symbol Parameter (V) to +125˚C Units (Note 9) C L = 50 pF Min Max tPLH Propagation Delay 5.0 1.0 15.0 ns S n to Zn tPHL Propagation Delay 5.0 1.0 14.5 ns S n to Zn tPLH Propagation Delay 5.0 1.0 13.5 ns E n to Zn tPHL Propagation Delay 5.0 1.0 11.5 ns E n to Zn tPLH Propagation Delay 5.0 1.0 12.5 ns I n to Zn tPHL Propagation Delay 5.0 1.0 12.0 ns I n to Zn Note 9:Voltage Range 5.0 is 5.0V±0.5V Capacitance Symbol Parameter Typ Units Conditions C IN Input Capacitance 4.5 pF V CC = OPEN C PD Power Dissipation 65.0 pF V CC = 5.0V Capacitance www.national.com 6

Physical Dimensionsinches (millimeters) unless otherwise noted

20 Terminal Ceramic Leadless Chip Carrier (L)

16-Lead Ceramic Dual-In-Line Package (D) www.national.com7

Physical Dimensionsinches (millimeters) unless otherwise noted (Continued) LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE- VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI- CONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or sys- tems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose fail- ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component in any component of a life support device or system whose failure to perform can be rea- sonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 16-Lead Ceramic Flatpak (F) 54AC153 • 54ACT153 Dual 4-Input Multiplexer National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,modifications,enhancements,improvements, and otherchanges toitsproductsand servicesatany timeand todiscontinueany productorservicewithoutnotice.Customersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allproductsare soldsubjecttoTI’s termsand conditionsofsalesuppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitshardwareproductstothespecificationsapplicableatthetimeofsaleinaccordancewithTI’s standard warranty.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessarytosupportthiswarranty.Exceptwhere mandated by governmentrequirements,testingofallparametersofeach productisnotnecessarilyperformed. TIassumes no liabilityforapplicationsassistanceorcustomerproductdesign.Customersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithcustomerproductsand applications,customersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany TIpatentright,copyright,mask work right, orotherTIintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIproductsorservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensefromTItouse such productsorservicesora warrantyorendorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectual propertyofthethirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalterationand isaccompanied by allassociatedwarranties,conditions,limitations,and notices.Reproductionofthisinformationwithalterationisan unfairand deceptive businesspractice.TIisnotresponsibleorliableforsuch altereddocumentation.Informationofthirdpartiesmay be subjecttoadditional restrictions. ResaleofTIproductsorserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatproductorservicevoidsall expressand any impliedwarrantiesfortheassociatedTIproductorserviceand isan unfairand deceptivebusinesspractice.TIisnot responsibleorliableforany such statements. TIproductsarenotauthorizedforuse insafety-criticalapplications(suchas lifesupport)where a failureoftheTIproductwouldreasonably be expectedtocause severepersonalinjuryordeath,unlessofficersofthepartieshave executedan agreementspecificallygoverning such use.Buyersrepresentthattheyhave allnecessaryexpertiseinthesafetyand regulatoryramificationsoftheirapplications,and acknowledgeand agreethattheyaresolelyresponsibleforalllegal,regulatoryand safety-relatedrequirementsconcerningtheirproducts and any use ofTIproductsinsuch safety-criticalapplications,notwithstandingany applications-relatedinformationorsupportthatmay be providedby TI.Further,Buyersmust fullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofTIproductsin such safety-criticalapplications. TIproductsareneitherdesignednorintendedforuse inmilitary/aerospaceapplicationsorenvironmentsunlesstheTIproductsare specificallydesignatedby TIas military-gradeor"enhanced plastic." Onlyproductsdesignatedby TIas military-grademeet military specifications.Buyersacknowledgeand agreethatany such use ofTIproductswhichTIhas notdesignatedas military-gradeissolelyat theBuyer's risk,and thattheyaresolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIproductsareneitherdesignednorintendedforuse inautomotiveapplicationsorenvironmentsunlessthespecificTIproductsare designatedby TIas compliantwithISO/TS 16949 requirements.Buyersacknowledgeand agreethat,iftheyuse any non-designated productsinautomotiveapplications,TIwillnotbe responsibleforany failuretomeet such requirements. FollowingareURLs where you can obtaininformationon otherTexas Instrumentsproductsand applicationsolutions: Products Applications Audio www.ti.com/audio Communicationsand Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP ® Products www.dlp.com Energyand Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocksand Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportationand Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap WirelessConnectivity www.ti.com/wirelessconnectivity TIE2E Community Home Page e2e.ti.com MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2011,Texas InstrumentsIncorporated