DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Features

  • Fast and simple installation
  • No torches or heat source required
  • No special tools required to install splice
  • Thick walls to resist puncture and abrasion damage
  • High Dielectric constant stress control included with 5/8 kV kits for shielded feeder cables, for minimizing size and electrical stress
  • Easy re-entry.

3M™ Motor Lead Splicing Kits 5300 Series 2 of 4 Kit Contents Each kit contains sufficient quantities of the following materials to make three splices (lugs and vinyl tape are not included), see chart below. Kit Component Kit Number 5300 Thru 5301 5302 Thru 5394 5311 Thru 5314 5316 Thru 5319 5321 Thru 5324 5331 Thru 5333 Lug covers (pigtail) X X X X Locking Pins X X Splice Cover (inline) X PST Cold Shrink Tubes X X Adapter Sleeves X X Scotch® Electrical Stress Control Tape 2220 X X Scotch® Linerless Rubber Tape 130C X X X Mastic Sealing Strips X X X X Solvent Cleaning cloths X X X Silicone Grease Lubricant X X X X X X Instruction Sheet X X X X X X

Applications

3M™ Motor Lead Splicing Kits 5300 Series can be used on cables with a rated operating temperature of 90°C and an emergency overload rating of 130°C. Splicing k its 5300 through 5314 are rated for 1000 Volts, and kits 5316 through 5334 are rated for 5/8 kV. To splice (insulate and seal) motor lead connections for:

  • 1000 Volts and less cables sized 16 AWG to 500 kcmil
  • 5/8 kV shielded and non-shielded feeder cables sized 8 AWG to 500 kcmil
  • Polyethylene cable
  • Cross linked polyethylene cable (XLP)
  • Ethylene propylene rubber cable (EPR)
  • Copper conductors Typical Properties Physical Properties (Test Method) (ASTM D412 unless otherwise noted) Typical Value US units (metric) Color Black

300 Modulus 480 psi (3,3 MPa)

Ultimate Tensile Strength 1400 psi (9,6 MPa) Ultimate Elongation 750% Die C Tear (ASTM D624C) 150 ppi (26,3 KN/m) Electrical Properties (Test Method) (ASTM D149) Typical Value US units (metric) Dielectric Strength Original 7 days in H2O, 90°C (194°F)

365 V/mil (14,3 MV/mil)

282 V/mil (11,1 MV/m)

*All values are averages and are not intended for specification purposes.

3M™ Motor Lead Splicing Kits 5300 Series 3 of 4 Splice Selection Table Type Kit Number Voltage Rating Range Feeder Cable (AWG & kcmil) Range Motor Lead (AWG & kcmil) Max. bolt Length (inches) Pigtail (1 hole lugs) 5300 5301 5302 5303 5304 1000 V 1000 V 1000 V 1000 V 1000 V 14 – 10 10 – 4 2 – 1/0 1/0 – 250 250 – 500 16 – 12 12 – 4 4 – 1/0 2 – 250 4/0 – 500 1 1/4 1 1/2 Inline 5311 5312 5313 5314 1000 V 1000 V 1000 V 1000 V 10 – 4 2 – 1/0 1/0 – 250 250 – 500 12 – 4 4 – 1/0 2 – 250 4/0 – 500 3./4 1 1/4 Pigtail (2 hole lugs) 5316 5317 5318 5319 1000 V 1000 V 1000 V 1000 V 8 – 4 2 – 1/0 1/0 – 250 250 – 500 10 – 4 4 – 1/0 2 – 250 4/0 – 500 1 1/4 1 1/2 Pigtail (Non- Shielded) 5316 5317 5318 5319 5/8 kV 5/8 kV 5/8 kV 5/8 kV 8 – 4 2 – 1/0 1/0 – 250 250 – 500 10 – 4 4 – 1/0 2 – 250 4/0 – 500 1 1/4 1 1/2 Pigtail (Shielded) 5321 5322 5323 5324 5/8 kV 5/8 kV 5/8 kV 5/8 kV 8 – 4 2 – 1/0 1/0 – 250 250 – 500 10 – 4 4 – 1/0 2 – 250 4/0 – 500 1 1/4 1 1/2 Inline (Shielded or Non-Shielded) 5331 5332 5333 5334 5/8 kV 5/8 kV 5/8 kV 5/8 kV 8 - 4 2 – 1/0 1/0 – 250 250 – 500 10 – 4 4 – 1/0 2 – 250 4/0 – 500 1 1/4 1 1/2 Typical Dimensions Kit Number L Inches (mm) 5300 5301 5302 5303 5304 2.1 (53) 3.4 (86) 4.2 (107) 5.3 (135) 6.7 (170) Kit Number L Inches (mm) 5316 5317 5318 5319 8.0 (203) 9.5 (241) 11.0 (1279) 13.0 (330) Kit Number L Inches (mm) 5311 5312 5313 5314 4 -5 (102 -127) 8 -9 (203 – 229) 9 – 10 (229 – 254) 12 – 13 (269 – 330) For inline splice kits: The longitudinal space required for assembly will be approximately 2L, to allow space for the splice while the connection is being made.

3M™ Motor Lead Splicing Kits 5300 Series 4 of 4 3M and Scotchlok are trademarks of 3M Company. Scotch is a registered trademark of 3M Company. CSA is a registered trademark of the Canadian Standards Association. Electrical Markets Division 6801 River Place Blvd. Austin, TX 78726-9000 800.245.3573 FAX: 800.245.0329 www.3M.com/electrical Please recycle © 3M 2017 All rights reserved 78-8127-9126-3 B Kit Number L Inches (mm) 5321 5322 5323 5324 7 8 (178 – 203) 8 – 9 (203 – 229) 9 – 10 (229 – 254) Kit Number L Inches (mm) 5331 5332 5333 5334 10 – 11 (254 – 279) 12 – 13 (269 – 330) 15 - 16 (381 – 406) 17 – 18 (432 – 457) Typical Dimensions, continued For inline splice kits: The longitudinal space required for assembly will be approximately 2L, to allow space for the splice while the connection is being made. Maintenance Components with this kit are stable under normal storage conditions. Normal stock rotation practices are recommended. The mastic and cold shrink insulator are not impaired by freezing or heated storage up to the flow temperature of the mastic. 3M cold shrink removable core material is polypropylene and recyclable with other waste. Shelf Life & Storage As provided in the expanded state, the 3M™ Motor Lead Splicing Kits 5300 Series have an on-shelf life of 3 years from date of manufacture when stored in a humidity controlled storage (10°C/50°F to 27°C/80°F and <75% relative humidity). Availability Please contact your local distributor; available from 3M.com/electrical [Where to Buy] or call 1-800-245-3573. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product, which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.