530-1A-06S0 OENINDIA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

FEATURES

l 6.3mm Flat terminals l Suitable Couplers available l Dual Contacts APPLICATION l A/C Blower l A/C Compressor l Engine Cooling Fan l Radiator Fan l Starter Motors l Rear Window Defogger l Battery Disconnection TECHNICAL DATA FOR CONTACT SIDE : GENERAL DATA FOR COIL SIDE Nominal Coil Power : 1.92W (Approx) Operating Power : 1.1W (Approx) Operate Time : 15 milli Seconds Release Time : 15 milli Seconds ** At nominal voltage without coil suppression (excluding bounce) 0 0 Ambient Temperature : -25 C to +85 C Maximum Temperature : 155 C Dielectric Strength : 500VRMS Insulation Resistance : 100 Meg. Ohms Min. At 500 VDC, 0

25 C RH 50

Vibration Resistance (without Change : 10-50Hz 4.4g (min) in the switching state>10µS) Shock Resistance (without Change : 30g, 8mS in the switching state>10µS) OPERATING CONDITIONS CIRCUIT DIAGRAM HEAVY DUTY RELAY Contact Configuration : 1A 1A (Dual) 1A (Dual) Contact Material : Silver Nickel Silver Nickel Silver Nickel / Tungsten* Contact Rating at 25 C - 12VDC (Res.) : 40A 50A 70A 24VDC (Res.) : 20A 25A 35A 5 5 5 Electrical Life Operations Min. : 1 x 10 1 x 10 1 x 10 6 6 6 Mechanical Life Operations Min. : 1 x 10 1 x 10 1 x 10 Contact Voltage Drop at 10 A (Min) : 30mV 30mV 30mV Maximum Switching Current : 120A 150A 240A@ 12.8 VDC For 3 Sec. RESISTIVE /INDUCTIVE/CAPACITIVE LOADS 30 85 86 87 * Parallel resistor or Diode Optional 30 85 86 87 Dual Contact Singe Contact *Dual Contact with Tungsten pre-contact / Silver nickel main contact Areas of Application Model : 53SO 53DO 53TO

*Lower pick-up Voltages available on request COIL DATA DIMENSIONS 06 4.8 5.2 20 09 6.8 7.2 55 12 9.0 9.6 75 18 13.5 14.4 165 24 18.0 19.2 250 48 36.0 38.4 1100 53 1 - 1A - 12 D 0 - XXX Product Series Nominal Coil Voltage (Refer Coil Data) S - Single Contact D - Dual Contact T - Dual Contact Heavy Duty 0-Without Bracket 1-With Bracket Contact Arrangement 1A - 1 Form A 0- No Resistor in Parallel to Coil 1 - With Resistor in Parallel to Coil Specialities If any *Pick-up Voltage VDC Version D Pick-up Voltage VDC Version T Coil Resistance without parallel resistor in Ohms ±10% Nominal Voltage VDC COVER RETENTION Pull : 20KgF Push : 20KgF TERMINAL STRENGTH Pull : 10KgF Push : 10KgF l High temperature winding wire l Special coil resistance & pick-up l For other custom solutions consult factory MECHANICAL DATA 8.0 19.0Ø5.046.0 28.0 4x0.8 4x6.30 11.5 2x0.8 28.0 25.5 33.0 Relay without Bracket Relay with Bracket AVAILABLE ON REQUEST 28.0 4x0.8 4x6.30 25.5 11.5 2x0.8 28.0 8.4 8.4 17.9 10.35

DATA ON VARIOUS TESTS CONDUCTED FOR OPERATING CONDITIONS TEST TEST CONDITION RESULT Relays successfully completed 100000 operations at given load Relay kept at 100 C Thermal cycling Shock Voltage Dropping Impact No change in operating parameters of the relay. Corrosion Resistance No damage to relay parts Jump Start Withstood successfully Coil Voltage : 14 VDC Load given : 25 A @ 12 VDC Duration : 5 Sec. On, 5 Sec. OFF No. of operation : 50000 The above test repeated at - 30 C for 50000 operations Relay subjected to :- 0 0 -30 C to + 100 C in 2 Hrs. with coil ON +100 C for 2 Hrs. with coil ON 0 0 +100 C to - 30 C in 2 Hrs. with 1 Hrs. Coil ON & 1 Hrs. Coil OFF -30 C for two Hrs. with Coil ON No. of Cycles : 3 Relay is subjected to :- Max. Voltage : 100VDC Shock Wave : Exponential Damping vibration Time : 500 micro Sec. Period : 30 Sec. Test Time : 10 Hrs. Relays dropped from a height of 1 Meter to a concrete floor

24 VDC for 1 minute conducting nominal current

No water ingression inside the relay Horizontal Plane:23rev. / Min. Water Pressure:0.03 Mpa Test time:10 Min *Typical values for relays with 12 VDC coil. For higher severity please consult factory All Parameters except the load given are same for 53 & 53PT Relays. Continuous Energisation test at Extreme temperature Conditions All operating parameters within the specifications after test After the test, all operating parameters of the relay are within specification. 5% Sodium Chloride solution applied to relay for 48 Hrs.