IDTF1650NLGI8 RENESAS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 22
Technical content
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 1 Rev1, March 2014 IDTF1650NLGI Datasheet Zero-DistortionTM Zero-DistortionTM GENERAL DESCRIPTION This document describes specifications for the F1650NLGI Zero/Complex IF Modulator implementing Zero-DistortionTM technology for low power consumption with improved ACLR. This device interfaces directly to a high performance Tx dual DAC. COMPETITIVE ADVANTAGE In typical multi-mode, multi-carrier basestation transmitters the modulator has limited linearity and high power consumption which penalizes the system ACLR and system Power consumptions budgets in a Digital- Pre-Distortion environment. The IDTF1650 is designed to eliminate these penalties by embedding Zero-DistortionTM technology into the device such that very high IP3 and IP2 are achieved with minimal current draw. Power consumption 4455%% IM3 Distortion 1122 ddBB PART# MATRIX Part# RF freq Range IP2O Power Cons. IP3O Noise FF11665500 660000 –– 22440000 ++6600 ddBBmm 558877 mmWW ++3366 ddBBmm --115588 ddBBmm//HHzz
FEATURES
Power Gain = 3.25dB Direct 100Ω differential drive from Tx DAC << 559900mmWW PPoowweerr CCoonnssuummppttiioonn @@ 22GGHHzz -158dBm/Hz Output Noise IP2O = +60dBm @ 2GHz IIPP33OO == ++3366ddBBmm @@ 22GGHHzz Excellent native LO and image suppression 600 MHz input 1dB Bandwidth 600 MHz to 2400MHz RF BW CCoonnssttaanntt LLOO iimmppeeddaannccee wwhheenn OOFFFF 3.3V Single Power Supply LO port can be driven single ended or differential 4mm x 4mm 24-pin TQFN package DEVICE BLOCK DIAGRAM
ORDERING INFORMATION
Bias +3.3VRF out I QControl STBY IDTF1650NLGI8 0.8 mm height package Green Industrial Temp range Tape & Reel Omit IDT prefix RF product Line
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 2 Rev1, March 2014 IDTF1650NLGI Datasheet ABSOLUTE MAXIMUM RATINGS VDD to GND -0.3V to +3.6V STBY -0.3V to (VDD + 0.3V) BB_I+, BB_I-, BB_Q+, BB_Q- -0.3V to 1.8V LO_IN -0.3V to 0.3V RF_OUT (VDD-0.35V) to (VDD-0.05V) Continuous Power Dissipation 1.5W θJA (Junction – Ambient) +45°C/W θJC (Junction – Case) The Case is defined as the exposed paddle +2.5°C/W Operating Temperature Range (Case Temperature) TCASE = -40°C to +105°C Maximum Junction Temperature 150°C Storage Temperature Range -65°C to +150°C Lead Temperature (soldering, 10s) +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 3 Rev1, March 2014 IDTF1650NLGI Datasheet IDTF1650 RECOMMENDED OPERATION CONDITIONS Parameter Comment Symbol min typ max units Supply Voltage(s) All VDD pins VDD 3.15 3.30 3.45 V Operating Temperature Case Temperature TCASE -40 25 +105 deg C LO Freq Range LO power -3dBm to +5dBm FLO 600 2400 MHz BB Freq Range FLO = 1950 MHz, BB_IQ = 200 mV PRF degrades < 1 dB FBB DC 600 MHz
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 4 Rev1, March 2014 IDTF1650NLGI Datasheet IDTF1650 SPECIFICATION See application circuit. Typical values are measured at VDD = +3.3V, FLO = 1950 MHz, PLO = 0 dBm, TCASE= +25°C, STBY = GND, BB_IQ frequency = 49, 50 MHz, BB_I&Q levels = 200 mVp-p each (14 dB backoff from 1V DAC compliance), I & Q = 0.250V common-mode bias unless otherwise noted. Parameter Comment Symbol min typ max units Logic Input High For STBY Pin VIH 1.07 V Logic Input Low For STBY Pin VIL 0.68 V Logic Current For STBY Pin IIH, IIL -100 +1 μA Supply Current (ON) Total VDD ISUPP 178 2101 mA Supply Current (STBY) Total VDD, STBY = VIH ISTBY 6 15 mA LO Power 600MHz to 2400MHz PLO -3 +5 dBm BB Input Resistance (Differential) Freq = 100 MHz RBB 113 Ω BB Common Mode Voltage DC couple to LCM DAC TCASE = -40C to +105C VDD = 3.3 V LO level = 0dBm VCM 0.1 0.25 0.8 V BB input voltage compliance range For each BB pin 0 1 Vpeak LO port Impedance Single Ended (RL < -10dB) Can be driven differentially ZLO 50 Ω RF port Impedance Single Ended (RL < -10dB) ZRF 50 Ω Power Gain G 2.25 3.25 4.25 dB LO Path noise Calc. from Noise v. POUT + 10 MHz offset, 1.0 GHz FLO ΦN_LO -157 dBc/Hz Output IP3 @ 850 MHz LO = 800 MHz IP3O1 35 dBm Output IP3 @ 2.0 GHz LO = 1950 MHz IP3O2 30 36 Output IP3 @ 2.45 GHz LO = 2400 MHz IP3O3 33 Output IP2 @ 850 MHz LO = 800 MHz IP2O1 63 dBm Output IP2 @ 2.0 GHz LO = 1950 MHz IP2O 552 60 Output IP2 @ 2.45 GHz LO = 2400 MHz IP2O3 60 LO (Carrier) Suppression Native, Uncorrected FLO = 1950 MHz LOsupp -37 -30 dBm Sideband (Image) Suppression Native, Uncorrected FLO = 1950 MHz SS -41 -30 dBc Output P1dB Output Compression P1dBO 15 dBm Output Noise 10 MHz offset from LO BB I&Q levels = 0 VP-P NSD -157 -158 dBm/Hz SPECIFICATION NOTES: 1 – Items in min/max columns in bold italics are Guaranteed by Test 2 – All other Items in min/max columns are Guaranteed by Design Characterization
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 5 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CONDITIONS Unless otherwise noted, the following conditions apply: Baseband I&Q levels = 200 mVPP each (-13 dBm / Channel / Tone) Baseband I&Q tones = 49, 50 MHz Low Side Injection TAMB = 25C, VCC = 3.30 V, LO Power = 0 dBm where TAMB is the ambient temperature VCM = 0.250 Volts, where CM is common mode Flo = 1.95GHz unless otherwise specified, where lo is Local Oscillator EVKit RF output Trace and Connector Losses De-Embedded EVkit RF output loss (Trace + Connector) -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 -40degC 25degC 85degC 100degC RF Frequency (GHz) Output Loss (dB)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 6 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-1-) OIP3 vs. TAMB OIP3 vs. LO level OIP2 vs. VCC OIP3 vs. VCC OIP2 vs. TAMB OIP2 vs. LO level -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Output IP3 (dBm) 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Output IP3 (dBm) 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Output IP2 (dBm) 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Output IP3 (dBm) -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Output IP2 (dBm) 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Output IP2 (dBm)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 7 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-2-) ICC vs. TAMB ICC vs. LO level Power Consumption vs. VCC ICC vs. VCC Power Consumption vs. TAMB Power Consumption vs. LO level 100 140 180 220 260 300 340 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Total Current (mA) 100 140 180 220 260 300 340 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Total Current (mA) 300 400 500 600 700 800 900 1,000 1,100 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Power Consumption (mW) 100 140 180 220 260 300 340 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Total Current (mA) 300 400 500 600 700 800 900 1,000 1,100 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Power Consumption (mW) 300 400 500 600 700 800 900 1,000 1,100 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Power Consumption (mW)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 8 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-3-) Gain vs. TAMB Gain vs. LO level RF Output Power vs. VCC Gain vs. VCC RF Output Power vs. TAMB RF Output Power vs. LO level -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Power Gain (dB) 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Power Gain (dB) -15 -13 -11 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Output RF Level (dBm) Total Baseband Input Power = -10 dBm = 200mVPP across 100Ω on I&Q 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Power Gain (dB) -15 -13 -11 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Output RF Level (dBm) -15 -13 -11 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Output RF Level (dBm) Total Baseband Input Power = -10 dBm = 200mVPP across 100Ω on I&Q
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 9 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-4-) Unadjusted LO Suppression vs. TAMB Unadjusted LO Suppression vs. LO level Unadjusted Sideband Suppression vs. VCC Unadjusted LO Suppression vs. VCC Unadjusted Sideband Suppression vs. TAMB Unadjusted Sideband Suppression vs. LO level -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Native LO Suppression (dBm) -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Native LO Suppression (dBm) -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Native Image Suppression (dBc) -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Native LO Suppression (dBm) -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Native Image Suppression (dBc) -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Native Image Suppression (dBc)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 10 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-5-) Baseband 2nd Harmonic vs. TAMB Baseband 2nd Harmonic vs. LO level Baseband 3rd Harmonic vs. VCC Baseband 2nd Harmonic vs. VCC Baseband 3rd Harmonic vs. TAMB Baseband 3rd Harmonic vs. LO level -90 -80 -70 -60 -50 -40 -30 -20 -10 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Baseband H2 Rejection (dBc) -90 -80 -70 -60 -50 -40 -30 -20 -10 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Baseband H2 Rejection (dBc) -90 -80 -70 -60 -50 -40 -30 -20 -10 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Baseband H3 Rejection (dBc) -90 -80 -70 -60 -50 -40 -30 -20 -10 25degC / 3.45V / 0dBm 25degC / 3.30V / 0dBm 25degC / 3.15V / 0dBm LO Frequency (GHz) Baseband H2 Rejection (dBc) -90 -80 -70 -60 -50 -40 -30 -20 -10 -40degC / 3.30V / 0dBm 25degC / 3.30V / 0dBm 90degC / 3.30V / 0dBm 105degC / 3.30V / 0dBm LO Frequency (GHz) Baseband H3 Rejection (dBc) -90 -80 -70 -60 -50 -40 -30 -20 -10 25degC / 3.30V / 5dBm 25degC / 3.30V / 0dBm 25degC / 3.30V / -3dBm LO Frequency (GHz) Baseband H3 Rejection (dBc)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 11 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-6-) LO Leakage (Carrier) Nulling Gain & IP3O Histograms [FLO = 1.95G, N = 1080] Performance vs. VCM [Native LO & Image Suppression] Image (Sideband) Nulling LO & Image Histograms [FLO = 1.95G, N = 1080] Performance vs. VCM [Gain, IP3, IP2, FLO = 1.95G] -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 0.9GHz 2.1GHz 2.4GHz -40degC 25degC 90degC 105degC LO Freq / VCC / LO Level (dBm) LO Suppression (dBm) Nulled Nulled NulledNulled 10% 15% 20% 25% 30% Percentage (%) Gain Bin (dB) / Output IP3 Bin (dBm) OIP3 Gain 27 28 29 30 31 32 33 34 35 36 37 38 39 40 -50 -45 -40 -35 -30 -25 LO Suppression (dBm) Image Suppression (dBc) VCM [Common Mode Voltage] (Volts) LO Suppr (dBm) / Image Suppr (dBc) -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 -3 0 5 0.9GHz 2.1GHz 2.4GHz -40degC 25degC 90degC 105degC LO Freq / VCC / LO Level (dBm) Sideband Suppression (dBc) Nulled NulledNulled 10% 12% 14% 16% 18% Percentage (%) Native LO Suppression / Image Suppression Bin (dBm / dBc) LO Suppr Image Suppr Power Gain (dB) IP3O / IP2O (dBm) VCM [Common Mode Voltage] (Volts) OIP3 OIP2 Gain
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 12 Rev1, March 2014 IDTF1650NLGI Datasheet TYPICAL OPERATING CURVES (-7-) Output Noise vs. Frequency Input Bandwidth (fixed LO = 2.092 GHz) I&Q Input Parallel Resistance/Capacitance Output Noise vs. POUT [VCC = 3.3V, TAMB = 25C] LO & RF Port Return Loss 1dB Compression -161 -157 -153 -149 -145 -141 Output Noise (dBm/Hz) LO Frequency (GHz) 3.3V / Ta = 25C / 0dBm LO 0 100 200 300 400 500 600 -40degC / 3.30V / 0 dBm 25degC / 3.30V / 0 dBm 100degC / 3.30V / 0 dBm 105degC / 3.30V / 0 dBm Baseband Input Frequency (MHz) Power Gain (dB) 100 110 120 130 140 0 100 200 300 400 500 600 Input Balanced RP (ohms) Baseband Input Frequency (MHz) -40degC / I -40degC / Q 25degC / I 25degC / Q 100degC / I 100degC / Q 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0 100 200 300 400 500 600 Input Balanced CP (pF) Baseband Input Frequency (MHz) -40degC / I -40degC / Q 25degC / I 25degC / Q 100degC / I 100degC / Q -160 -158 -156 -154 -152 -150 -148 -146 -24 -20 -16 -12 -8 -4 0 4 8 Output Noise (dBm/Hz) RF Output Power (dBm)
1.0 GHz
-30 -25 -20 -15 -10 Return Loss (dB) Frequency (GHz) LO Return Loss RF Return Loss Output P1dB (dBm) LO Frequency (GHz) -3 0 5 -3 0 5 -3 0 5 3.15V 3.30V 3.45V Output P1dB (dBm) -40degC 25degC 105degC LO Frequency = 1.95 GHz LO Level (dBm) VSUPPLY
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 13 Rev1, March 2014 IDTF1650NLGI Datasheet GENERIC DAC INTERFACE DAC ClockDual DAC II+ = 20 mAP Xformer 0 Tx VCO/PLL IDTF1650 ZIF/CIF Mod II- = 20 mAP In-Phase (I) Quadrature (Q) IQ- = 20 mAP IQ+ = 20 mAP 50 Ω +/- 1% 50 Ω +/- 1% VCOMPLIANCE = 1VP-P VCOMPLIANCE = 1VP-P 50 Ω +/- 1% 50 Ω +/- 1% 100 Ω LPF (opt.) 100 Ω LPF (opt.) Rcore-ON Rcore-ON Rcore-ON Rcore-ON
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 14 Rev1, March 2014 IDTF1650NLGI Datasheet PACKAGE DRAWING (4X4 24 PIN)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 15 Rev1, March 2014 IDTF1650NLGI Datasheet PIN DIAGRAM TOP View (looking through the top of the package) LO- LO+ VDD GND GND [NC] BB_I- GND [NC]GND RF_OUT GND BB_I+ STBY Exposed Pad GND R_DIST GND BB_Q- GND Package Drawing 4 mm x 4 mm package dimension 2.60 mm x 2.60 mm exposed pad 0.5 mm pitch 24 pins 0.75 mm height 0.25 mm pad width 0.40 mm pad length 87 9 1110 12 20 192123 2224 BB_Q+ GND [NC] VDD CO 0.35 mm GNDGND [TEST] BLACK denotes recommended external connection [RED] denotes internal connection GND [NC] GND [NC]
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 16 Rev1, March 2014 IDTF1650NLGI Datasheet PIN DESCRIPTIONS Pins Name Function 1 STBY STBY Mode. Pull this pin high for Standby Mode (<15 mA). Pull low or ground for Normal Operation. 2, 5, 8, 12, 13, 19, 23 GND Ground these pins. 11, 14, 15, 17, 20 NC IDT recommends to ground these pins. 3, 4 LO+, LO- Local oscillator (LO) 50 ohm differential or 25ohm each pin single-ended input. Pins should be ac-coupled. For 50 ohm single-ended operation, ac-couple USED Pin to 50 ohm termination and ac-couple UNUSED pin to GND. 6 TEST Test pin. Ground this pin.
7 R_DIST Connect the specified resistor from this pin to ground to set the
RF distortion amplifier current. 9, 10 BB_Q-, BB_Q+ Quadrature differential baseband input. Internally matched to 100 ohms. 16 RF_OUT RF output. Must be ac-coupled. 18, 24 VDD Power Supply. Bypass to GND with capacitors as shown in the Typical Application Circuit as close to pin as possible. 21, 22 BB_I+, BB_I- In-Phase differential baseband input. Internally matched to100 ohms. — EP Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the specified RF performance.
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 17 Rev1, March 2014 IDTF1650NLGI Datasheet EVKIT SCHEMATIC
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 18 Rev1, March 2014 IDTF1650NLGI Datasheet EVKIT SCHEMATIC (CONTINUED) POWER SUPPLIES All supply pins should be bypassed with external capacitors to minimize noise and fast transients. Supply noise can degrade noise figure and fast transients can trigger ESD clamps and cause them to fail. Supply voltage change or transients should have a slew rate smaller than 1V/20uS. In addition, all control pins should remain at 0V (+/-0.3V) while the supply voltage ramps or while it returns to zero.
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 19 Rev1, March 2014 IDTF1650NLGI Datasheet EVKIT BOM APPLYING VCM AT THE BASEBAND INPUTS With L1, L2, L3, and L4 unpopulated, the common mode voltage is set by VR2 and VR4. The voltage set by VR2 has a DC path through the balun transformer T1 to pins BB_I+ and BB_I-, as highlighted. This also applies for VR4, T2, and pins BB_Q+ and BB_Q-. With this configuration, the same voltage will be applied to BB_I+ and BB_I- and the same voltage will be applied to BB_Q+ and BB_Q-. The I and Q common mode voltages may be different from each other to null LO (carrier) leakage. F1650 SE Item # Value Size/Rev Desc Mfr. Part # Mfr. Supplier Part # Supplier Part Reference Qty 1 8pF 0402 CAP CER 8pF 0402 50V 5% C0G GRM1555C1H8R0DZ01DMURATA 490-3212-1-ND Digikey C2 1 2 10nF 0402 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01D MURATA 490-1313-1-ND Digikey C4,6,8,10,17 5 3 39pF 0402 CAP CER 39PF 50V 5% C0G 0402 GRM1555C1H390JZ010 MURATA 490-1286-1-ND Digikey C1 1 4 0.6pF 0402 CAP CER 8pF 0402 50V 5% C0G GJM1555C1HR60BB01D MURATA 490-6078-1-ND Digikey C18 1 5 0.1uF 0402 CAP CER 0.1UF 16V 10% X7R 0402 GRM155R71C104KA88D MURATA 490-3261-1-ND Digikey C7,9 2 6 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey R3,8,9,C13-16 7 7 6.34K 0402 RES 6.34K OHM 1/10W 1% 0402 SMD ERJ-2RKF6341X Panasonic P6.34KLCT-ND Digikey R18 1 8 24.9 1206 RES TF 24.9 OHM 1% 0.25W 1206 RMCF1206FT24R9CT-NDRMCF RMCF1206FT24R Digikey R5,12 2 9 47K 0402 RES 47.0K OHM 1/16W 1% 0402 SMD RC0402FR-0747KL Yageo 311-47.0KLRCT- Digikey R1 1 10 1K 2719 TRIMMER 1K OHM 0.25W SMD TS63Y-1.0KCT-ND Vishay/Sfernice TS63Y102KR10 Digikey VR2,4 2 11 1.8n 0402 0402CS Ceramic Chip Inductor 0402CS-1N8XJLU CoilCraft 0402CS-1N8XJLU CoilCraft L5 1
12 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M 3M9447-ND Digikey J2,5,8,9 4
13 SMA_END_LAUNCH .062 SMA_END_LAUNCH (Small) 142-0711-821 Emerson Johnson 530-142-0711-821 Mouser J3,4,7,10 4 14 SMA_END_LAUNCH .062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson 530-142-0701-851 Mouser J1,6 2 15 2:1 Balun SM-22 2:1 Center Tap Balun ADT2-1T+ Mini Circuits ADT2-1T+ Mini Circuits T1,2 2
16 F1650 QFN-24 IQ MOD F1650 IDT F1650-010 IDT U1 1
17 PCB 02 Printed Circuit Board F1650 SE EVKIT REV 02 Coastal Circuits 1
18 BOM 05 Bill Of Material
19 DNP 2719 VR1,3
20 DNP 0402 C3,5,11,12
21 DNP 0402 R2,6,10,14,16
22 DNP 1206 R4,7,11,13
L1, L2, L3, and L4 are all UNPOPULATED
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 20 Rev1, March 2014 IDTF1650NLGI Datasheet EVKIT PICTURE: Note: VCC connection on evaluation board is VDD Power Supply on the datasheet. VDD connection on evaluation board is used to set baseband pin common mode (CM) voltage (see schematic)
ZIF/CIF Modulator 600MHz to 2400MHz Zero-DistortionTM Modulator 21 Rev1, March 2014 IDTF1650NLGI Datasheet TOP MARKINGS F1650GI ZC1337N 30F010Y Part Number Date Code [YYWW] (Week 37 of 2013) Lot CodeDie Step
TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) © 2020 Renesas Electronics Corporation. All rights reserved.