DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Features

  • Packaged as 28-pin SSOP (150 mil body)
  • Synchronizes fractional clocks rising edges
  • Pin configurable multiplication/division ratio
  • Slices frequency or period
  • SYNC pulse output indicates aligned edges
  • Input clock frequency of 600 kHz to 200 MHz
  • Output clock frequencies up to 160 MHz
  • Very low jitter
  • Duty cycle of 45/55 up to 160 MHz
  • Operating voltage of 3.3V
  • Pin selectable drive strength
  • Multiple outputs available when combined with fanout buffers
  • Industrial temperature version available
  • Pb (lead) free package Block Diagram ICLK 2xDRIVE CLK1 CLK2 Reference Divider PLL R6:R0 F6:F0 S1:S0 PDTS Feedback DividerFBIN Divide by 2 SYNC DIV2 Feedback can come from CLK1 or CLK2 (not both) PDTS OECLK2 PDTS GND VDD

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 2 ICS527-01 REV G 051310 Pin Assignment 28 pin 150 mil body SSOP Frequency Range Table To cover the range from 10 to 18 MHz (0 to 70°C) and 8 to 16 MHz (-40 to 85°C), select address 01 to generate 2x your desired output frequency, then configure CLK2 to generate CLK1/2. Pin Descriptions ICLK FBIN GND CLK2 OECLK2 2XDRIVE GND PDTS F0 F5 F1 F4 CLK1 VDD VDD DIV2 S0 R1 R6 R3 R4 S1 S0 CLK1 Output Frequency (MHz) Commercial (0 to 70°C) I ndustrial (-40 to 85°C) 0 0 37 - 75 35 - 70 0 1 18 - 37 16 - 35 1 0 4 - 10 4 - 8 1 1 75 -160 70 - 140 CLK2 Operation Table OECLK2 DIV2 CLK2 0X Z 1 0 SYNC

11 C L K 1 / 2

1,2, 24-28 R5, R6, R0-R4 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up resistor.

3 DIV2 Input Selects CLK2 function to output a SYNC signal or a divide by 2 of CLK1 based

on the table above. Internal pull-up resistor. 4, 5 S0, S1 Input Select pins for output divider determined by user. See table above. Internal pull-up resistor. 6, 23 VDD Power Connect to VDD. 7 ICLK Input Reference clock input. 8 FBIN Input Feedback clock input. 9, 20 GND Power Connect to ground. 10 OECLK2 Input CLK2 Output Enable. CLK2 tri-stated when low. Internal pull-up resistor. 11 2XDRIVE Input Clock output drive strength doubled when high. Internal pull-up resistor. 12-18 F0-F6 Input Feedback divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up resistor. 19 PDTS Input Power Down. Active low. Turns off entire chip when low, both clock outputs are tri-stated. Internal pull-up resistor. 21 CLK2 Output Output clock 2. Can be SYNC output or a low skew divide by 2 of CLK1. 22 CLK1 Output Output clock 1.

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 3 ICS527-01 REV G 051310 External Components Decoupling Capacitors As with any high performance mixed-signal IC, the ICS527-01 must be isolated from system power supply noise to perform optimally. Decoupling capacitors of 0.01µF must be connected between each VDD and the PCB ground plane. The capacitor must be connected close to the device to minimize lead inductance. Series Termination Resistor Clock output traces over one inch should use series termination. To series terminate a 50Ω trace (a commonly used trace impedance), place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. Using the Clock Slicer First use DIV2 to select the function of the CLK2 output. If DIV2 is high, a divide-by-2, low skew version of CLK1 is present on CLK2. If DIV2 is low, a SYNC pulse is generated on CLK2. The SYNC pulse goes high synchronously with the rising edges of ICLK and CLK1 that are de-skewed. The SYNC function operates at CLK1 frequencies up to 66 MHz. If neither CLK1/2 or a SYNC pulse are required, then CLK2 should be disabled by connecting OECLK2 to ground. This will also give the lowest jitter on CLK1. Next, the feedback scheme should be chosen. If CLK2 is being used as a SYNC pulse, or is tri-stated, then CLK1 must be connected to FBIN. If CLK2 is selected to be CLK1/2 (DIV2=1, OECLK2=1) then either CLK1 or CLK2 must be connected to FBIN. The choice between CLK1 or CLK2 is illustrated by the following examples where the device has been configured to generate CLK1 that is twice the frequency on ICLK. Using CLK1 as feedback will always result in synchronized rising edges between ICLK and CLK1 if CLK1 is used as feedback. CLK2 could be a falling edge compared to ICLK. Therefore, wherever possible, it is recommended to use CLK2 for feedback, which will synchronize the rising edges of all three clocks. More complicated feedback schemes can be used, such as incorporating multiple output buffers in the feedback path. An example is given later in the datasheet. The fundamental property of the ICS527-01 is that it aligns rising edges on ICLK and FBIN at a ratio determined by the reference and feedback dividers. The drive strength is selected by the 2XDRIVE pin. If high drive strength is required, we recommend tying this pin low. Lastly, the divider settings should be selected. This is described in the following section. Determining ICS527-01 Divider Settings The user has full control in setting the desired output clock over the range shown in the table on page 2. The user should connect the divider select input pins directly to ground (or VDD, although this is not required ICLK CLK1 Feedback CLK1 CLK2 phase is indeterminate ICLK CLK1 CLK2 CLK2 Feedback

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 4 ICS527-01 REV G 051310 because of internal pull-ups) during Printed Circuit Board layout, so the ICS527-01 automatically produces the correct clock when all components are soldered. It is also possible to connect the inputs to parallel I/O ports in order to switch frequencies. The output of the ICS527-01 can be determined by the following simple equation: Where: Reference Divider Word (RDW) = 0 to 127 Feedback Divider Word (FDW) = 0 to 127 FB Frequency is the same as either CLK1 or CLK2 depending on feedback connection Also, the following operating ranges should be observed: S1 and S0 should be set for the frequency of CLK1, according to the Frequency Range Table on page 2. The device can be operated below the lower limits stated in table 2, however, jitter and skew may be higher. Therefore, if your expected output frequency covers more than one frequency range, use the setting for the highest frequency expected. The dividers are expressed as integers. For example, if a 50 MHz output on CLK1 is desired from a 40 MHz input, the reference divider word (RDW) should be 2 and the feedback divider word (FDW) should be 3 which gives the required 5/4 multiplication. Then R6:R0 is 0000010, F6:F0 is 0000011 and S1:S0 is 00. Also, this example assumes CLK1 is connected to FBIN.S1:S0 is set by referring to the Frequency Range Table. The setting for 50 MHz is 00. For assistance with configuring the device, please send a description of your requirements using the “Technical Support” link at www.idt.com. FB Frequency Input Frequency FDW 2+ 300kHz Input Frequency

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 5 ICS527-01 REV G 051310 Typical Example The following connection diagram shows the implementation of the example from the previous section. This will generate a 50 MHz clock synchronously with a 40 MHz input. A SYNC pulse is desired and the 1x output drive is selected.T Note: The series termination resistor is located before the feedback trace. This will give the following waveforms: Multiple Output Example In this example, an input clock of 125 MHz is used. Eight copies of 50 MHz are required as are eight copies of 25 MHz, de-skewed and aligned to the 125 MHz input clock. The following solution uses the MK74CB218 which has dual 1 to 8 buffers with low pin-to-pin skew. ICLK GND OECLK2 2XDRIVE CLK1 CLK2 GND VDD VDD DIV2 FBIN PDTS

50 MHz

0.01 F

40 MHz

0.01 F VDD

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 6 ICS527-01 REV G 051310 Using the equation for selecting dividers gives: If FDW = 0, then RDW = 8. This gives the required divide-by-5 function. Setting pin DIV2 = 1 gives both a 25 MHz and a 50 MHz output from the ICS527-01. The FBIN pin is connected to the QA7 output of the MK74CB218. This aligns all the outputs of the MK74CB218 with the 25 MHz input since the ICS527-01 aligns rising edges on the ICLK and FBIN pins. The propagation delay of the buffer is compensated by the PLL. In this example, series termination resistors have been omitted for clarity but should be used on all clock outputs. PCB Layout Recommendations For optimum device performance and lowest output phase noise, the following guidelines should be observed. 1) Each 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No via’s should be used

125 MHz,

25 MHz,

50 MHz,

0.01 F

125 MHz

25 MHz

0.01 F VDD QB5 QA3 QB6 QB7 VDD GND QA5 QA6 QA7 OE QB3 QB4 GND VDD VDD VDD VDD QA1 QA2 QB1 QB2 INA QA0 INB QB0QA4 GND GND 0.01 F0.01 F MK74CB218 ICS527-01 The layout design above produces the waveforms shown below. Note: Series terminating resistors are not shown. 0.01 F (FDW + 2) (RDW + 2)

25 MHz = 125 MHz x

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 7 ICS527-01 REV G 051310 between decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. 2) To minimize EMI the 33Ω series termination resistor, if needed, should be placed close to the clock outputs. 3) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS527-01. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS527-01. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Recommended Operation Conditions Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +70° C Item Rating Supply Voltage, VDD 7 V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature (Commercial) 0 to +70 ° C Ambient Operating Temperature (Industrial) -40 to +85 ° C Storage Temperature -65 to +150 ° C Junction Temperature 125 ° C Soldering Temperature 260 ° C Parameter Min. Typ. Max. Units Ambient Operating Temperature, ICS527R-01 0 – +70 ° C Ambient Operating Temperature, ICS527R-01I -40 – +85 ° C Power Supply Voltage (measured in respect to GND) 3 3.3 3.6 V Parameter Symbol Conditions Min. Typ. Max. Units Operating Voltage VDD 3 3.3 3.6 V Supply Current IDD 15 MHz in, 60MHz out, no load 8m A Supply Current, Power Down IDDPD PDTS =0 20 μA Input High Voltage V IH 2V

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 8 ICS527-01 REV G 051310 Input Low Voltage V IL 0.8 V Input High Voltage, ICLK and FBIN VIH Pins 7 and 8 VDD/2+1 V Input Low Voltage, ICLK and FBIN VIL Pins 7 and 8 VDD/2-1 V Output High Voltage V OH 2XDRIVE = 0, IOH = -12 mA 2.4 V Output Low Voltage V OL 2XDRIVE = 0, IOL = 12 mA 0.4 V Output High Voltage V OH 2XDRIVE = 1, IOH = -25 mA 2.4 V Output Low Voltage V OL 2XDRIVE = 1, IOL = 25 mA 0.4 V Short Circuit Current I OS 2XDRIVE = 0, CLK outputs ±70 mA Short Circuit Current I OS 2XDRIVE = 1, CLK outputs ±140 mA On-chip Pull-up Resistor R PU 270 k Ω Parameter Symbol Conditions Min. Typ. Max. Units

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 9 ICS527-01 REV G 051310 Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature -40 to +85° C Note 1: Assumes clocks with same rise time, measured from rising edges at VDD/2. External Components The ICS527-01 requires two 0.01 µF decoupling capacitors to be connected between VDD and GND, one on each side of the chip. They must be connected close to the device to minimize lead inductance. No external power supply filtering is required for this device. A 33Ω series terminating resistor should be used on the CLK1 and CLK2 output pins. Parameter Symbol Conditions Min. Typ. Max. Units Input Frequency F IN 0.6 200 MHz Output Frequency, CLK1 F OUT 0 to +70° C4 1 6 0 M H z -40 to +85° C4 1 4 0 M H z CLK1 Frequency for Correct SYNC Operation 66 MHz Output Rise Time t OR 0.8 to 2.0 V 1 ns Output Fall Time t OF 2.0 to 0.8 V 1 ns Output Clock Duty Cycle t OD Measured at VDD/2, CL=15 pF 45 50 55 % Power Down Time, PDTS low to clocks tri-stated 50 ns Power Up Time, PDTS high to clocks stable 10 ms Absolute Clock Period Jitter t ja Deviation from mean ± 90 ps One sigma Clock Period Jitter t js 40 ps Skew of Output Clocks t IO CLK1 to CLK2, Note 1 -250 250 ps Input Capacitance C IN 4p F Input to Output Skew t IO ICLK to FBIN, Note 1 -250 250 ps Device to Device Skew t pi Common ICLK, at FBIN 0 500 ps

CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER 10 ICS527-01 REV G 051310 Package Outline and Package Dimensions (28-pin SSOP, .150 mil Body, 0.025 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95, MO-153

Ordering Information

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. Part / Order Number Marking Shipping Packaging Package Temperature 527R-01LF ICS527R-01LF Tubes 28-pin SSOP 0 to +70 ° C 527R-01LFT ICS527R-01LF Tape and Reel 28-pin SSOP 0 to +70 ° C 527R-01ILF ICS527R-01ILF Tubes 28-pin SSOP -40 to +85 ° C 527R-01ILFT ICS527R-01ILF Tape and Reel 28-pin SSOP -40 to +85 ° C INDEX AREA 1 2 D E1 E SEATING PLANE A AA e - C - b aaa C c L Millimeters Inches Symbol Min Max Min Max A 1 . 3 51 . 7 5. 0 5 3. 0 6 9 A1 0.10 0.25 .0040 .010 A2 -- 1.50 -- .059 b 0 . 2 00 . 3 0. 0 0 8. 0 1 2 C 0 . 1 80 . 2 5. 0 0 7. 0 1 0 D 9.80 10.00 .386 .394 E 5 . 8 06 . 2 0. 2 2 8. 2 4 4 E1 3.80 4.00 .150 .157 e 0.635 Basic 0.025 Basic L 0 . 4 01 . 2 7. 0 1 6. 0 5 0 α 0° 8° 0° 8°

© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names a nd marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA Corporate Headquarters Integrated Device Technology, Inc. www.idt.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 For Tech Support www.idt.com/go/clockhelp Innovate with IDT and accelerate your future networks. Contact: www.IDT.com ICS527-01 CLOCK SLICER USER CONFIGURABLE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER