4833

4833 3M | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

3M™ Matrix Resin 4833 Technical Data Sheet Product Description 3M™ Matrix Resin 4833 is a two-part, low viscosity, nanoparticle modified Bis‑F epoxy curable at low temperatures optimized for extreme toughness applications. 3M Matrix Resin 4833 can be used in filament winding, pultrusion and with typical heated bath processes and in RTM processes. Suggested Applications

• Pultruded or wound tubes and shafts exposed to extreme environmental impacts
• High energy flywheels where microcracking is a top concern
• RTM structural parts requiring extreme toughness and compressive strength Handling/Application Information Prior to application, 3M™ Scotch-Weld™ Elastomeric Coating EC-5816 should be thoroughly agitated for 3-5 minutes

3M™ Matrix-Resin 4833 Benefits

• Longer part life due to improved performance after impact for exposed tubes or shafts, and lower residual stresses in manufactured parts
• Higher torque carrying capacity for rotating tubes and shafts enabling longer, stronger or lighter weight designs
• Enables single piece flywheel designs due to lower CTE and shrinkage during cure; longer part life by reduced microcracking via enhanced fracture toughness
• Enables new RTM part designs with improved performance and/or lighter weight
• 3.5 year shelf life at room temperature

3M™ Matrix-Resin 4833 Handling/Cure Information Note: This processing information is general or summary in nature and not intended to replace user’s careful consideration of the unique circumstances involved in its use of 3M products. To improve the ease of mixing with the curative, 3M™ Matrix Resin 4833 can be heated to 40°C before being combined with the curative. It is recommended to minimize the heat exposure of the resin in order to maximize the shelf life of the product. When 3M™ Matrix Resin 4833 is used in filament winding applications with curatives (i.e. DICY), it will normally require approximately 10°C higher heating of the resin coating bath to achieve an equal viscosity to a typical epoxy system and to achieve good fiber wet‑out. The use of 3M™ Matrix Resins does not require any changes to the curing conditions recommended for typical curatives – follow cure cycle as recommended by curative supplier. In some cases, the cure cycle can be shortened due to the significant reductions of exotherm and shrinkage experienced with 3M ™ Matrix Resins. This is an especially important consideration in thick composite parts. 3M™ Matrix Resin 4833 may have undesirable interactions with surface‑active additives such as mold releases, air releasers, de‑foamers, pigments, fillers, tougheners, and additives. These undesirable interactions can adversely affect the performance of the 3M ™ Matrix Resin, even at low concentrations. It is recommended initially to evaluate only the 3M™ Matrix Resin and curative components, eliminating all fillers and additives. Information on curatives suitable for use with 3M™ Matrix Resin 4833 is available by calling 3M Customer Service at 1‑800‑235‑2376.

3M™ Matrix-Resin 4833 Shipping and Storage Shelf life is one year under proper storage conditions. The product should be stored indoors at 70 ‑80°F (21‑27°C). Higher temperatures shorten normal shelf life. The product should not be placed near any heating equipment. Refrigeration or freezer storage can extend shelf life. The product should be used as soon as possible after the package is opened and any unused product should be properly sealed with original or similar package. Precautionary Information Refer to product label and Safety Data Sheet (SDS) for health and safety information before using this product. For SDS visit our website https://www.3m.com/3M/en_US/company-us/SDS-search/. Additional Information 5714. If you are outside of the U.S., please contact your nearest 3M re presentative.

3M™ Matrix-Resin 4833 These products were manufactured under a 3M Quality Management System registered to the AS9100 standard Automotive & Aerospace Solutions Division 3M Center St. Paul, MN 55144-1000 Phone 1-800-328-1684 Web www.3M.com/aerospace 4833 Issue date: 8/2019 3M is a trademark of 3M Company. All other trademarks are the property of their respective owners. © 3M 2019. All rights reserved. Technical Information: The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information. Product Selection and Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property. Warranty, Limited Remedy, and Disclaimer: Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.