408-1729 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
1 of 11 © 2016 TE Connectivity Ltd. family of companies. All Rights Reserved. *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names m ay be trademarks of their respective owners. PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com. 408-1729
22 NOV 16 Rev K
(AWG) Head or Tool Part Number Color Code Dot
47820 Red 8 Hydraulic Crimping Head 69051
Hydraulic Hand Tool 59974-1
47821 Blue 6
47822 Yellow 4
47823 Red 2
47824 Blue 1/0
Hydraulic Crimping Head 69066 47825 Yellow 2/0
47915 Red 3/0
47918 Blue 4/0
- INTRODUCTION Crimping Dies 47820 through 47823 are used with Crimping Head 69051 or Hand Tool 59974 --1. Crimping Dies 47824, 47825, 47915, and 47918 are used with Crimping Head 69066. The dies crimp pre -insulated AMPOWER* terminals onto wire sizes 4 through 1/0 AWG, TERMINYL* terminals and s plices onto wire sizes 8 through 4/0 AWG, TERMINYL splices with step-down adapters onto wire sizes 16-14 through 1/0 AWG, and PLASTI-GRIP* terminals and splices onto wire sizes 8 through 4/0 AWG. Refer to Figure 1 to e nsure compatibility of crimping die, head or tool, and wire size. NOTE Dimensions in this document are in millimeters [with inches in brackets]. Figures and illustrations are for reference only and are not drawn to scale. For detailed information about the head or tool, refer to the instructions packaged with the head or tool. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION (FIGURE 1) Each crimping die consists of a stationary die (nest) and a moving die (anvil). The stati onary die features a locator. Each die contains a color code dot that matches the color code of the terminal and spli ce. When mated, the dies form a crimping chamber. Crimping Dies; PN 47820 thru 47825, 47915, and 47918 Crimping Dies; PN 47820 thru 47825, 47915, and 47918 (Typical)
- DIE INSTALLATION AND REMOVAL DANGER To avoid personal injury, ALWAYS release hydraulic pressure to hose or control and disconnect power unit from power supply before installing or removing dies. 3.1. Installation 1. Remove latch pin and open yoke on crimping head (see Figure 2). Figure 2 2. Loosen the setscrew in the yoke. 3. Insert the shank of the stationary die into the yoke, and tighten the setscrew. NOTE The stationary die has a large shank and the moving die has a small shank, as shown in Figure 2. 4. Extend the ram until the ram setscrew is visible. 5. Loosen the setscrew in the ram. 6. Insert the shank of the moving die into the ram, and tighten the setscrew. CAUTION To avoid damage to the dies, be sure the moving and stationary dies are properly oriented. 7. Activate the tool or power unit to allow the ram to return to the “down” position. 8. Close the yoke and insert the latch pin. 3.2. Removal 1. Remove latch pin and open yoke on crimping head. 2. Loosen the setscrew in the yoke, and remove the stationary die. 3. Extend the ram until the ram setscrew is visible. 4. Loosen setscrew in ram and remove moving die.
- Holding the terminal in place, close the yoke and insert the latch pin. CAUTION Be sure latch pin is fully inserted, otherwise damage to the die and tool or head will occur when the tool or power unit is activated. 7. Holding wire in place, activate tool or power unit to complete crimp. 8. When crimp is completed, remove the latch pin, open the yoke, and remove the terminal. NOTE If terminal sticks in die after crimping, apply a rocking action to the terminal to remove it from the die. Wipe light oil on the dies to prevent sticking, or use spray dry lubricant. 9. Inspect the crimp according to Section 5. 4.2. Crimping Splices without Step-Down Adapter DANGER Avoid personal injury. When operating tool or power unit, exercise caution while holding splice or wire near the crimping are a. 1. Strip wires to the dimensions listed in Figure 3. Do not nick or cut the wire strands. 2. Select the proper col or-coded splice for the wire size. The wire size stamped on the splice and on the crimping die must match the wire size selected. 3. Insert the stripped wire into the wire barrel of the end of the splice to be crimped until the wire bottoms against the wire stop within the splice. 4. Remove crimping head latch pin and open yoke. 5. Place the splice in the stationary die. Grasp the end of the splice to be crimped and poi nt the opposite end toward the top of the head yoke at a 30° (approximate) angle. Rotate the end of the splice to be crimped into the die. Position the edge of the window indent against the locator. Refer to Figure 5. Figure 5 Top of Yoke Edge of Window Indent Resting Against Locator Rotate End of Splice to be Crimped into Stationary Die End of Splice Pointed Toward Top of Yoke at Approximately 30°Angle
- Holding the splice in place, close the yoke and insert the latch pin. CAUTION Be sure latch pin is fully inserted, otherwise damage to the dies and tool or head will occur when the tool is activated. 7. Holding wire in place, activate tool or power unit to complete first wire barrel crimp. 8. When crimp is completed, remove latch pin, open yoke and remove the splice. NOTE If splice sticks in die after crimping, apply a rocking action to the splice to remove it from the die. Wipe light oil on dies to reduce sticking, or use spray dry lubricant. 9. To crimp the other half of splice, reposition un-crimped end of splice in the stationary die and follow the same procedure used to crimp the first half of splice. 10. Inspect the crimp according to Section 5. 4.3. Crimping Splices with Step-Down Adapter DANGER Avoid personal injury. When operating tool or power unit, exercise caution while holding splice or wire near the crimping area. 1. Strip wires to the dimensions listed in Figure 3. Do not nick or cut the wire strands. 2. Select the proper splice, adapter, and crimping die for the wire size (see Figure 6). NOTE Note that the end of the splice containing the adapter has a different color code. Use the crimping die for the larger wire size to crimp both ends of the splice. For example, use Crimping Die 47820 (for wire size 8 AWG) to crimp both ends of the splic e with step-down adapter for stepping down from wire size 8 to 16-14 AWG. Figure 6 3. Insert stripped wire into the wire barrel of the end of the splice to be crimped until the wir e bottoms against the wire stop within the splice (refer to Figure 3). 4. Remove crimping head latch pin and open yoke. 5. Place the splice in the stationary die. Grasp the end of the splice to be crimped and poi nt the opposite end toward the top of the head yoke at a 30° (approximate) angle. Rotate the end of the splice to be crimped into the die. Position the edge of the window indent against the locator. Refer to Figure 5.
- Holding the splice in place, close the yoke and insert the latch pin. CAUTION Be sure latch pin is fully inserted, or damage to the dies and tool or head will occur when the tool is activated. 7. Holding the wire in place, activate tool or power unit to complete first wire barrel cr imp. 8. When crimp is completed, remove latch pin, open yoke and remove splice. NOTE If splice sticks in die after crimping, apply a rocking action to the splice to remove it from the die. Wipe light oil on dies t o reduce sticking, or use spray dry lubricant. 9. To crimp the other half of splice, reposition un-crimped end of splice in the stationary die and follow the same procedure used to crimp the first half of splice. 10. Inspect the crimp according to Section 5. 4.4. Crimping PLASTI-GRIP Butt Splices DANGER Avoid personal injury. When operating tool or power unit, exercise caution while holding butt splices or wire near crimping area. 1. Strip wires to the dimensions listed in Figure 3. Do not nick or cut the wire strands. 2. Select the proper color-coded butt splice for the wire size. The wire size stamped on the butt splice and on the crimping die must match the wire size selected. 3. Remove crimping head latch pin and open yoke. Remove the stationary die from the yoke, then remove the locator from the stationary die. Re-assemble the stationary die onto the yoke. CAUTION To avoid damage to the dies, be sure the stationary die is properly oriented with the moving die. 4. Insert the stripped wire into the wire barrel of the end of the butt splice to be crimped until the wire bottoms against the wire stop within the splice. 5. Place the butt splice in the stationary die with the wire barrel of the end of the spli ce to be crimped centered over the crimping chamber (see Figure 7). Figure 7 6. Holding butt splice in place, close the yoke and insert latch pin. CAUTION Be sure latch pin is fully inserted, otherwise damage to the die and tool or head will occur when the tool or power unit is activated. 7. Holding wire in place, activate tool or power unit to complete first wire barrel crimp.
- When crimp is completed, remove latch pin, open yoke, and remove the butt splice. NOTE If butt splice sticks in die after crimping, apply a rocking action to the butt splice to remove it from the die. Wipe light oil on dies to reduce sticking, or use spray dry lubricant. 9. To crimp the other half of butt splice, reposition un-crimped end of splice in the stationary die and follow the same procedure used to crimp the first half of splice. NOTE Be sure to re-assemble locator onto stationary die after crimping PLASTI-GRIP butt splices. 10. Inspect the crimp according to Section 5. 5. CRIMP INSPECTION Inspect crimped terminals and splices by checking the features described in Figure 9. Use on ly the terminals and splices that meet the conditions shown in the “ACCEPT” column. 6. MAINTENANCE / INSPECTION DANGER To avoid personal injury, ALWAYS release hydraulic pressure to hose or control and disconnect power unit from power supply before performing maintenance or inspection procedure. Each crimping die is thoroughly inspected before packaging. Since there is a possibil ity of damage during shipment, the crimping die should be inspected immediately upon arrival at your facilit y. Regular inspections should be performed by quality control personnel. A record of sche duled inspections should remain with the dies and/or be supplied to supervisory personnel responsible for the dies. Though recommendations call for at least one inspection a month, the inspection frequency shou ld be based on the amount of use, ambient working conditions, operator training and skill, and established company standards. CAUTION Regular inspections should include checking torque setting of (4) screws in accordance with Figure 8. Crimping Die PN Wire Size (AWG) Screw Torque Setting Specification (inch-pounds) Crimping Die PN Wire Size (AWG) Screw Torque Setting Specification (inch-pounds) 47820 8 28 47824 1/0 49 47821 6 28 47825 2/0 49 47822 4 28 47915 3/0 49 47823 2 28 47918 4/0 49 Figure 8 Torque (4) Screws in Accordance with Figure 8.
6.1. Daily Maintenance It is recommended that each operator of the dies be made aware of-and responsible for-the following s teps of daily maintenance: 1. Remove dust, dirt, and other contaminants with a clean brush, or a soft, lint--free cloth. Do NOT use objects that could damage the dies. 2. Make certain the dies are protected with a THIN coat of any good SAE 20 motor oil. Do not oil excessively. 3. When the dies are not in use, mate them and store in a clean, dry area. 6.2. Visual Inspection 1. Remove all lubrication and accumulated film by immersing the dies in a suitable c ommercial degreaser that will not affect paint or plastic material. 2. Make sure all die components are in place. If replacements are necessary, refer to the replacement parts listed in Figure 12. 3. Check components for wear. Remove and replace worn components. 4. Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage is evident, the dies must be repaired before returning them to service (see Section 7, REPLACEMENT AND REPAIR). 6.3. Gaging the Crimping Chamber The die closure inspection is accomplished using plug gages. A suggested gage design an d the GO and NO- GO diameters of the plug gage elements are shown in Figure 10. Figure 10
The following procedure is recommended for inspecting the die closures: 1. Mate the dies until it is evident that they have bottomed. Hold the dies in this position . 2. Align the GO element with the crimping chamber. Push element straight into the crimpi ng chamber without using force. The GO element must pass completely through the crimping chamber as shown in Figure 11. 3. Align the NO-GO element and try to insert it straight into the crimping chamber. The NO- GO element may start entry but must not pass completely through as shown in Figure 11. If the crimping chamber conforms to the gage inspection, the crimping die is considered dimensionally correct and should be lubricated with a THIN coat of SAE 20 motor oil. If the crimping chamber DOES NOT conform to the gage inspection not, the dies must be rep aired before returning them to service (see Section 7, REPLACEMENT AND REPAIR). For additional information concerning the use of a plug gage, refer to Instruction Sheet 408-7424. Figure 11 7. REPLACEMENT AND REPAIR The parts listed in Figure 12 are customer-replaceable. A complete inventory can be stocked and controlled to prevent lost time when replacement of parts is necessary. Order replacement parts through your TE Connectivity Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 1-717-986- 7605, or write to: CUSTOMER SERVICE (038-035) TE CONNECTIVITY CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105—3608 NOTE Dies may be returned for evaluation and repair. For die repair service, contact a TE Representative at 1-800-526-5136.
- REVISION SUMMARY Add screw torque and LOCTITE application to process resulting in a new Figure 8, renumbe ring of subsequent Figures, and CAUTIONS in SECTIONS 6 and 8. Revised quantities of Items 2, 3, 5, 6 in Figure 12. Replacement Parts Part Numbers for Crimping Die Item View A View B
Description
Assy 47820 47821 47822 47823 47824 47825 47915 47918 1 47941 47944 47947 47950 47910 47913 47916 47919 Die, Moving 1 2 47940 47943 47946 47949 47911 47914 47917 47920 Die, Stationary 1 3 313336-1 313336-2 313336-3 313337-1 46606 313337-2 313337-3 313337-4 Locator 1 4 2-21000-0 2-306105-5 2-306105-5 4-306105-4 3-21000-0 Screw 2 5 21018-5 21018-6 Nut 2 6 4-306105-5 2-306105-5 2-21000-2 4-306105-6 6-305927--4 Screw 2 7 313322-4 313322-3 313322-2 313322-1 313323-1 313323-2 313323-3 313323-4 Plate, Flare 2 8 304383 304384 304385 1-45992-0 45992-3 45992-7 45992-8 45992-9 Plate, Flare, Lower 1
9 N/A 45992-2 45992-1 45992-4 45992-5 45992-6 Plate, Flare,
Apply LOCTITE THREADLOCKER BLUE 242 or LOCTITE THREADLOCKER BLUE 243 to threads of items 4, 5, and 6. Torque screws to applicable specification in Figure 8. Figure 12 LOCTITE, THREADLOCKER BLUE 242, and THREADLOCKER BLUE 243 are trademarks. VIEW A VIEW B