461011220101 WURTH | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Scale - 5:1 This electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body, Wurth Elektronik must be asked for a written approval. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before by the user before usage. DATEFILE REV BY Date Checked Drawn Name Scale
DESCRIPTION
Drawing.- No. A4 SIZE 4.7x3.8mm Detect Switch, vertical right side, SMD version 461011220101 14-03-21 Fandrey WS-DESV 5:1 14-05-22a DaFOperating Direction System: Solid Edge ST4 14-03-21 Hsu 4,5 3,8 4,7 ±0,2 2,4 4,7 0,7 4,9 ±0,2 3,3 0,7 SPECIFICATION >Rating: 1mA 5VDC >Contact Resistance : Initial : 500mOhm max. After Life Test : 1Ohm max. >Insulation Resistance : min. 100MOHM at 250VDC >Dielectric Strength : 250VAC for 1 minute >Bounce : 10ms MATERIAL >Actuator: LCP UL 94V-0 >Base : LCP UL 94V-0, color Black >Frame : PA46 UL HB, color Black >Contact spring: Stainless Steel with silver plating >Terminal: Copper Alloy with silver plating SOLDERING INFORMATION >Terminal in SMD version >Reflow soldering according to JEDEC J-STD 020 Hot Air >Hand soldering under 350°C for 3sec. max ENVIRONMENTAL Storage condition : -40°C ~ +85°C . Operation condition : -40°C ~ +85°C Compliance : ROHS, Reach HANDLING ADVISE >Set a delay time according to our definition bounce >Please operate the switch only in the direction , which is advise in our specification >Design the operation distance so, so that it can reach 3,2mm or lower at least. Recommend is to design the switch so, that the operation point can reach the total travel position >Protect the switch , do not overstress our parts. >For more information’s, please refer to our pre-caution guide PACKAGING INFORMATION >Tape & Reel Part number Force Schematic Life Cycle 461 011 220 101 60gf max SPST- NO 100.000 0,1 +0,0 -0,1 3,8 Total Travel Position (Measure Position) 2,3 Schematic 3,5 +0,1 -0,0 5,1 +0,1 -0,0 2,4 ±0,1 1,2 ±0,1 P.C.B Mounting Plan 1 2 3 4 R 3 0,7 2,5 +0,2 -0,0 Operating Direction 1 2 3 4 1 2 3 4 3,2 +0,5 -0,0 Switching on Position
System: Solid Edge ST4 Drawing.- No. 461011220101 165° -180v C detail C B B Packaging is referred to the international standard IEC 60286 -3:2007 Feeding direction STARTEND Top Tape Chip Cavity Sprocket Hole Embossment A A Cover tape D0 P2 A 0 W F T top cover tape NO COMPONENT min 160mm COMPONENTS NO COMPONENT min. 100mm COVER TAPE min. 400mm A0 B0 W P1 T T1 T2 K0 D0 E1 E2 F P0 P2 VPE / packaging unit size 6410xxxx 5,00 5,60 16,00 12,00 0,35 0,10 5,25 4,80 1,50 1,75 14,25 7,50 4,00 2,00 1500 Polystyrene tolerance Tape A B C D N W1 W2 W3 W3 Tape width 16 mm 330,00 1,50 13,00 20,20 100,00 16,40 22,40 15,90 19,40 tolerance Pull-of force Tape width 16 mm 0,1 N - 1,3 N C BD W2 N A W** close to center