4578A KISTLER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 2

Technical content

for Tensile and Compression Forces, 4578A_000-866e-09.11 This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. ©2010 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland Tel. +41 52 224 11 11, Fax +41 52 224 14 14, info@kistler.com, www.kistler.com Kistler is a registered trademark of Kistler Holding AG. Force Type 4578A... Load cells for tension and compression Type 4578A... can be used in the laboratory and in industrial environments.

  • Measuring accuracy better than 0,20 %FSO
  • Small
  • Stainless steel construction
  • Simple mounting

Description

Strain gages are applied to the flexural diaphragms in the load cell are strain gages (DMS) and deliver a bridge output voltage directly proportional to the measurand during concentric load application. The force being measured must be applied to the thread along the central axis of the Type 4578A... . A force distributing cap or an adapter for the particular application must be used for this purpose, and introduction of shear or torsion avoided. Lateral forces within ±2,5 ° of the perpendicular force may be neglected. Higher lateral forces must be kept away from the load cell through design measures as shown in the articulated mounting configurations. The strain gage load cell is available for seven different mea - suring ranges from 0 … 100 N to 0 … 10 kN.

Applications

The standardized rated sensitivity and ease of mounting al- low simple retrofitting of existing structures with the load cell. Depending on the particular requirements, static, quasistatic and dynamic tensile and compression forces can be measured. Direction of measurement tensile/compression Maximum working load % 150 Dynamic load % 70 (recommended) Operating temperature range °C –20 ... 50 Rated temperature range °C 15 ... 50 Temperature influence on zero %FSO/K ≤±0,02 on span %FSO/K ≤±0,02 Weight (without cable) kg ≤0,5 Material stainless steel Degree of protection (sensor body) (acc. to IEC/EN 60529) IP42 Bridge resistance strain gage, full bridge circuit Input/Output Ω 350 nominal Accuracy %FSO ≤±0,2 (Combined value for non-linearity, hyster esis and repeatability with unchanged mounting position) Reference supply voltage VDC ≤10 Rated sensitivity mV/V 2,0 ±0,005 Zero signal %FSO ≤±3 Measuring deflection mm 0,05 ... 0,4 Deviations may occur Technical Data

Type 4578A... 4578A_000-866e-09.11 This information corresponds to the current state of knowledge. Kistler reserves the right to make technical changes. Liability for consequential damage resulting from the use of Kistler products is excluded. ©2010 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland Tel. +41 52 224 11 11, Fax +41 52 224 14 14, info@kistler.com, www.kistler.com Kistler is a registered trademark of Kistler Holding AG. Dimensions Fig. 1 : Dimensions strain gage load cell Type 4578A... Mounting Instructions The load cell must be mounted on a flat surface with uniform load application as free from shear forces as possible. Mounting and In- stallation Aid Fig. 2: Force dis- tributing cap Type 4578AZ01 Nom. load Weight Type 4578A... 0,5 kg Nom. load Measuring deflection

200 N 0,05 mm

500 N 0,11 mm

1 kN 0,10 mm 2,5 kN 0,19 mm 5 kN 0,33 mm 10 kN 0,40 mm Tightening torque of fixing screws Type Size Tightening torque 4578A... M6 9 N·m Optional Accessories Type

  • Force distributing cap 4578AZ01 Measuring Range [kN] 0,1 0,1 0,2 0,2 0,5 0,5 1 1 2 2 5 5 10 10 Connector Plug 6 pin M16 circular connector 9 pin D-Sub connector Ordering Key Type 4578A Included Accessories
  • None Advice for connector plug C1 and C3 C1 connector is applicable for DMF-P family C3 connector is applicable for maXYmos family 2Signal + Signal – Sense – Supply – Supply + Sense + Signal + Signal – Supply – Supply + Electrical Connection C3 approx. 3 m shielded, highly flexible cable, 9 pin D-Sub connector Electrical Connection C1 approx. 3 m shielded, highly flexible cable, 6 pin M16 circular connector approx. 84 ø52 ø48,6 ø68 ø20 ø6,4 M12 45 ° 8x45 ° (=360 °) 22,5 ° ø60 ø70