4405982

4405982 YAGEO | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 21

Technical content

Product Specification – May 10, 2023 V.16 DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS High-Voltage NP0/X7R

500 V TO 3 KV

0.47 pF to 33 nF

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 ORDERING INFORMATION - GLOBAL PART NUMBER, PHYCOMP CTC & 12NC All part numbers are identified by the series, size, tolerance, TC material, packing style, voltage, process code, termination and capacitance value. YAGEO BRAND ordering code GLOBAL PART NUMBER (PREFERRED ) CC XXXX X X XXX X X X XXX (1) SIZE – INCH BASED (METRIC) 0805 (2012) / 1206 (3216) / 1210 (3225) / 1808 (4520) / 1812 (4532) / 2220 (5750) (2) TOLERANCE B = ± 0.1pF C = ± 0.25 pF D = ± 0.5 pF G = ± 2% J = ± 5% K = ± 10% M = ± 20% (3) PACKING STYLE R = Paper/PE taping reel; Reel 7 inch K = Blister taping reel; Reel 7 inch P = Paper/PE taping reel; Reel 13 inch F = Blister taping reel; Reel 13 inch * Paper taping reel: 1. case size 0805/1206, thickness less than 1.0mm. * Blister taping reel: 1. case size 0805/1206, thickness more than 1.0mm. 2. 1210 to 2220. (4) TC MATERIAL NPO = NP0 X7R = X7R (5) RATED VOLTAGE B = 500V Floating design: Z = 630V C = 1KV D = 2 KV S = 2.5KV E = 3 KV (6) CONTROL CODE A: Anti-arc coating B: Standard Type (7) PROCESS N = NP0 B = X7R (8) CAPACITANCE VALUE 2 significant digits+number of zeros The 3rd digit signifies the multiplying factor, and letter R is decimal point Example: 121 = 12 x 101 = 120 pF SCOPE This specification describes High - Voltage NP0/X7R series chip capacitors with lead -free termi nations.

APPLICATIONS

PCs, Hard disk, Game PCs Power supplies LCD panel ADSL, Modem

FEATURES

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 CONSTRUCTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. The inner electrodes are connected to the two end terminat ions and finally covered with a layer of plated tin (NiSn). The terminations are lead -free. A cross section of the structure is shown in Fig.1. Detailed Cross Section Barrier Layer (Ni) Dielectric Material End Termination/ External Electrode (Cu) Dielectric Material Barrier Layer (Ni) End Termination/ External Electrode (Cu) Termination Finish (100% Matte Sn) Inner Electrodes (Ni) Inner Electrodes (Ni) Termination Finish (100% Matte Sn) Fig. 1 Surface mounted multilayer ceramic capacitor construction Table 1 For outlines see fig.2 DIMENSION OUTLINES For dimension see Table 1 Fig. 2 Surface mounted multilayer ceramic capacitor dimension TYPE L1 (mm) W (mm) T (MM) L2 / L3 (mm) L4 (mm) min. max. min. 0805 0.25 0.75 0.70 0.85 ± 0.10 1.25 ± 0.20 1206 0.25 0.75 1.40 0.85 ± 0.10 1.25 ± 0.20 1.60 ± 0.20 1210 0.25 0.75 1.40 1.25 ± 0.20 1.60 ± 0.20 2.00 ± 0.20 1808 4.5 ± 0.40 2.00 ± 0.30 1.25 ± 0.20 1.35 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 0.25 0.75 2.20 1812 4.5 ± 0.40 3.20 ± 0.20 0.85 ± 0.10 1.25 ± 0.20 1.35 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 0.25 0.75 2.20

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 CAPACITANCE RANGE & THICKNESS FOR NP0 Table 2 Sizes from 0805 to 1210 CAP. 0805 1206 1210 1.0 pF 0.6± 0.1 0.6± 0.1 0.85± 0.1 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 0.85± 0.1 0.6± 0.1 1.25± 0.2 0.85± 0.1 1.25± 0.2 1.25± 0.2 1.25± 0.2 12 pF 1.25± 0.2 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 1.25± 0.2 56 pF 1.25± 0.2 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 CAP. 0805 1206 1210 220 pF 0.6± 0.1 1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 0.85± 0.1 1.0 nF 1.2 nF 1.5 nF 2.2 nF 1.25± 0.2 2.7 nF 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 1.6± 0.2 1.6± 0.2 10 nF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request CAPACITANCE RANGE & THICKNESS FOR NP0 Table 3 Sizes from 0805 to 1210 (continued)

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 CAPACITANCE RANGE & THICKNESS FOR NP0 Table 4 Sizes from 1808 to 1812 CAP. 1808 1812 0.47 pF 0.56 pF 0.68 pF 0.82 pF 1.0 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 1.6± 0.2 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 CAP. 1808 1812 220 pF 1.25± 0.2 1.25± 0.2 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1.0 nF 1.2 nF 1.5 nF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request CAPACITANCE RANGE & THICKNESS FOR NP0 Table 5 Sizes from 1808 to 1812 (continued)

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 Table 6 Sizes from 0805 to 1210 CAPACITANCE RANGE & THICKNESS FOR X7R CAP. 0805 1206 1210 100 pF 150 pF 0.85± 0.1 220 pF 1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 330 pF 470 pF 680 pF 1.0 nF 1.6± 0.2 1.5 nF 1.25± 0.2 2.2 nF 1.60± 0.2 3.3 nF 1.25± 0.2 1.25± 0.2 4.7 nF 6.8 nF 10 nF 1.25± 0.2 1.25± 0.2 15 nF 22 nF 1.60± 0.2 1.6± 0.2 1.6± 0.2 33 nF 1.60± 0.2 2.0± 0.2 47 nF 68 nF 1.6± 0.2 100 nF 2.0± 0.2 NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-6 series is on request 3. For products with 5% tolerance, please contact local sales force before ordering

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 Table 7 Sizes from 1808 to 1812 CAPACITANCE RANGE & THICKNESS FOR X7R CAP. 1808 1812 2020 100 pF 150 pF 1.6± 0.2 220 pF 330 pF 1.35±0.15 470 pF 1.35±0.15 680 pF 1.0 nF 2.0± 0.2 1.25± 0.2 1.35±0.15 1.6± 0.2 1.5 nF 2.2 nF 1.6± 0.2 3.3 nF 4.7 nF 6.8 nF 1.6± 0.2 10 nF 15 nF 22 nF 33 nF 1.6± 0.2 1.6± 0.2 47 nF 68 nF 2.0± 0.2 100 nF 1.6± 0.2 150 nF 2.0± 0.2 220 nF 330 nF 470 nF 680 nF 1 µF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-6 series is on request 3. For products with 5% tolerance, please contact local sales force before ordering

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 DESCRIPTION VALUE Capacitance range 0.47 pF to 33 nF Capacitance tolerance NP0 C < 10 pF ± 0.25 pF, ± 0.5 pF Dissipation factor (D.F.) NP0 C < 30 pF ≤ 1 / ( 400 + 20C ) C ≥ 30 pF ≤ 0.1 % X7R ≤ 2.5 % Insulation resistance after 1 minute at Ur (DC) Rins ≥ 10 GΩ or Rins × C ≥ 500 seconds whichever is less Rins × C ≥ 100 Ω.F(2) Maximum capacitance change as a function of temperature (temperature characteristic/coefficient): NP0 ± 30 ppm/°C X7R ± 15% Operating temperature range: NP0/X7R –55 °C to +125 °C NOTE 5% tolerance of capacitance value isn't available for X7R full product range, please contact local sales force before ordering 2. X7R/0805/≥3.9nF X7R/1206/≥12nF X7R/1210/≥12nF X7R/1808/≥18nF X7R/1812/≥27nF X7R/2220/≥150nF

ELECTRICAL CHARACTERISTICS

NP0/X7R DIELECTRIC CAPACITORS; NISN TERMINATIONS Unless otherwise stated all electrical values apply at an ambient temperature of 20±1 °C, an atmospheric pressure of 86 to 106 kPa, and a relative humidity of 63 to 67%. Table 8

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 Fig. 3 Typical temperature coefficient as a function of temperature Sample limits (broken lines). Requirement levels (dotted lines) HIGH-VOLTAGE NP0 CCA044 7.5 2.5 40 0 40 80 120 T (oC) Fig. 4 Typical tan δ as a function of temperature HIGH-VOLTAGE X7R Fig. 5 Typical capacitance change as a function of temperature Fig. 6 Typical tan δ as a function of temperature

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 SOLDERING RECOMMENDATION Table 9 SOLDERING METHOD SIZE 0402 0603 0805 1206 ≥ 1210 Reflow Reflow only ≥ 1.0 µF ≥ 2.2 µF ≥ 4.7 µF Reflow only Reflow/Wave --- < 1.0 µF < 2.2 µF < 4.7 µF --- TEST TEST METHOD PROCEDURE REQUIREMENTS Mounting IEC 60384-

4.3 The capacitors may be mounted on printed-circuit boards or

4.4 Any applicable method using × 10 magnification In accordance with specification

Capacitance 4.5.1 NP0: f = 1 MHz for C ≤ 1 nF, measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 °C X7R: f = 1 KHz for C ≤ 10 µF, measuring at voltage 1 Vrms at 20 °C Within specified tolerance Dissipation Factor (D.F.)

4.5.2 NP0:

f = 1 MHz for C ≤ 1 nF , measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 °C X7R: f = 1 KHz for C ≤ 10 µF, measuring at voltage 1 Vrms at 20 °C In accordance with specification Insulation Resistance

4.5.3 Ur ≥ 500 V: At 500 V for 1 minute In accordance with specification

Table 10 Test procedures and requirements

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Coefficient

4.6 Capacitance shall be measured by the steps shown

in the following table. The capacitance change should be measured after 5 min at each specified temperature stage. Step Temperature(°C) a 25± 2 b Lower temperature± 3°C c 25± 2 d Upper Temperature± 2°C e 25± 2 (1) NP0: Temperature Coefficient shall be calculated from the formula as below Temp, Coefficient = 610T xC1 C1-C2 Δ [ppm/°C] C1: Capacitance at step c C2: Capacitance at 125°C (2) X7R: Capacitance Change shall be calculated from the formula as below ∆C = C1-C2 x 100% C1: Capacitance at step c C2: Capacitance at step b or d NP0: ∆ C/C: ± 30ppm X7R: ∆ C/C: ± 15% Adhesion IEC 60384- 4.7 A force applied for 10 seconds to the line joining the terminations and in a plane parallel to the substrate Force size ≥ 0603: 5N Bending Strength 4.8 Mounting in accordance with IEC 60384-22 paragraph 4.3 No visible damage Conditions: bending 1 mm at a rate of 1 mm/s, radius jig 5 mm ∆C/C NP0: within ± 1% or 0.5 pF, whichever is greater X7R: ± 10%

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 TEST TEST METHOD PROCEDURE REQUIREMENTS Resistance to Soldering Heat 4.9 Precondition: 150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature Preheating: for size ≤ 1206: 120 °C to 150 °C for 1 minute Preheating: for size >1206: 100 °C to 120 °C for 1 minute and 170 °C to 200 °C for 1 minute Solder bath temperature: 260 ± 5 °C Dipping time: 10 ± 0.5 seconds Recovery time: 24 ±2 hours Dissolution of the end face plating shall not exceed 25% of the length of the edge concerned ∆C/C NP0: within ±0.5% or 0.5 pF, whichever is greater X7R: ± 10% D.F. within initial specified value Rins within initial specified value Solderability 4.10 Preheated to a temperature of 80 °C to 140 °C and maintained for 30 seconds to 60 seconds. 1. Temperature: 235± 5°C / Dipping time: 2 ± 0.5 s 2. Temperature: 245± 5°C / Dipping time: 3 ± 0.5 s (lead free)Depth of immersion: 10mm The solder should cover over 95% of the critical area of each termination Rapid Change of Temperature IEC 60384-

4.11 Preconditioning;

150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature 5 cycles with following detail: 30 minutes at lower category temperature 30 minutes at upper category temperature Recovery time 24 ± 2 hours No visual damage ∆C/C NP0: within ± 1% or 1 pF, whichever is greater X7R: ± 15% D.F. meet initial specified value Rins meet initial specified value Damp Heat 4.13 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Damp heat test: 500 ± 12 hours at 40 ±2 °C; 90 to 95% R.H. 4. Recovery: NP0: 6 to 24 hours X7R: 24 ± 2 hours 5. Final measure: C, D, IR P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to “IEC 60384 4.1” and then the requirement shall be met. No visual damage after recovery ∆C/C NP0: within ± 2% or 1 pF, whichever is greater X7R: ± 15% D.F. NP0: ≤ 2 x specified value X7R: ≥ 25 V: ≤ 5% Rins NP0: ≥ 2,500 MΩ or Rins x Cr ≥ 25s whichever is less X7R: ≥ 500 MΩ or Rins x Cr ≥ 25s whichever is less

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 TEST TEST METHOD PROCEDURE REQUIREMENTS Endurance IEC 60384- 4.14 1. Preconditioning, X7R only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR Endurance test: Temperature: NP0/X7R: 125 °C Specified stress voltage applied for 1,000 hours. High-Voltage series follows the stress conditions below: Voltage NPO X7R 500/630V 1.3 x Ur 1.2 x Ur ≥ 1KV 1.2 x Ur 1.1 x Ur 3. Recovery time: 24 ± 2 hours 4. Final measure: C, D, IR *Applied 1.2 x Ur for NP0/1206/2.2nF to 10nF/500V to 630V. P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to “IEC 60384 4.1” and then the requirement shall be met. No visual damage ∆C/C NP0: within ± 2% or 1 pF, whichever is greater X7R: ± 15% D.F. NP0: ≤ 2 x specified value X7R: ≥ 25 V: ≤ 5% Rins NP0: ≥ 4,000 MΩ or Rins x Cr ≥ 40s whichever is less X7R: ≥ 1,000 MΩ or Rins x Cr ≥ 50s whichever is less Voltage Proof Specified stress voltage applied for 1~5 seconds Ur = 500 V series applied (1.3 Ur + 100) Ur > 500 V: 1.3 Ur Ur ≥ 1KV: 1.2 Ur Charge/Discharge current less than 50mA No breakdown or flashover

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 THICKNESS CLASSES AND PACKING QUANTITY SIZE CODE THICKNESS CLASSIFICATION PACKING CODE. TAPE WIDTH QUANTITY PER REEL Ø 180 MM /

7 INCH

Ø 330 MM /

13 INCH QUANTITY

E 7 INCH 13 INCH Paper Blister Paper Blister 0805 0.6 ± 0.1 mm R P 8 mm 4,000 --- 20,000 --- 10,000 0.85 ± 0.1 mm R P 8 mm 4,000 --- 15,000 --- 8,000 1.25 ± 0.2 mm K F 8 mm --- 3,000 --- 10,000 5,000 1206 1210 2.0 ± 0.2 mm K 8 mm --- 2,000 1,000 --- --- --- 2.5 ± 0.2 mm K 8 mm --- 1,000 500 --- --- --- 1808 1812 Table 11

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 Fig. 7 Paper/PE tape PAPER/PE TAPE SPECIFICATION Table 12 Dimensions of paper/PE tape for relevant chip size; see Fig.3 SIZE CODE SYMBOL Unit: mm A0 B0 W E F P0 (1) P1 P2 Ø D0 K0 T NOTE 1. P0 pitch tolerance over any 10 pitches is 0.2 mm

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 Fig. 8 Blister tape BLISTER TAPE SPECIFICATION K0: so chosen that the orientation of the component cannot change For W = 8 mm: T2 = 3.5 mm max. For W = 12 mm: T2 = 6.5 mm max. Table 13 Dimensions of blister tape for relevant chip size; see Fig.8 SIZE CODE SYMBOL Unit: mm A0 B0 K0 W E F Ø D0 Ø D1 P0 (2) P1 P2 T2 NOTE 1. Typical capacitor displacement in pocket 2. P0 pitch tolerance over any 10 pitches is ±0.2 mm

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 REEL SPECIFICATION Fig. 9 Reel Table14 Reel dimensions; see Fig.9 TAPE WIDTH SYMBOL Unit: mm A N C W1 W2max. PROPERTIES OF REEL Material: polystyrene Surface resistance: <10 10 X/sq.

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16

REVISION HISTORY

REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 16 May 10, 2023 - - Add NP0/1206/2.2nF to 10nF/500V to 630V Version 15 Dec. 15, 2021 - - I.R. Spec. updated X7R/0805/≥3.9nF X7R/1206/≥12nF X7R/1210/≥12nF X7R/1808/≥18nF X7R/1812/≥27nF X7R/2220/≥150nF - 0805 / 1206 / 1210 dimension updated Version 14 Oct. 26, 2021 - - Add 500V/630V Version 13 Feb. 28, 2021 - - Add NPO/1206/0.47pF to 10pF with 0.85 mm Version 12 Dec. 01, 2020 - - Add X7R/0805/1.5nF to 3.3nF/1KV. NPO/0805/ 56pF to 82pF/1KV Version 11 Jul. 13, 2018 - - Add NPO/1206/10pF to 47pF/3KV Version 10 Mar. 7, 2017 - - 0805 L4 spec updated Version 9 Jan. 16, 2017 - - Product range updated Version 8 Oct. 12, 2015 - - Product range updated Version 7 May 21, 2014 - - Product range updated Version 6 Jun. 17, 2012 - - Product range updated Version 5 Sep 25, 2012 - - Product range updated Version 4 Aug 08, 2011 - - Product range updated Version 3 Jan 19, 2011 - - Dimension updated - Add NP0 0805 1KV Version 2 Feb 02, 2010 - - Change to dual brand datasheet that describe High-Voltage NP0/X7R series with RoHS compliant - Replace the high voltage part of pdf files: UP-NP0X7R_HV_1K-to-4KV_1 and UY-NP0X7R_HV_1K-to-4KV_1 - Description of "Halogen Free compliant" added - Product range updated - Define global part number - Test method and procedure updated Version 1 Sep 30, 2005 - - Thickness revised Version 0 Sep 12, 2005 - - New

Surface-Mount Ceramic Multilayer Capacitors Product specification High-Voltage NP0/X7R 500 V to 3 KV www.yageo.com May 10, 2023 V.16 LEGAL DISCLAIMER YAGEO, its distributors and agents (collectively, “YAGEO”), hereby disclaims any and all liabilities for any errors, inaccuracies or incompleteness contained in any product related information, including but not limited to product specifi cations, datasheets, pictures and/or graphics. YAGEO may make changes, modifications and/or improvements to product related information at any time and without notice. YAGEO makes no representation, warranty, and/or guarantee about the fitness of its pro ducts for any particular purpose or the continuing production of any of its products. To the maximum extent permitted by law, YAGEO disclaims (i) any and all liability arising out of the application or use of any YAGEO product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for a particular purpose, non -infringement and merchantability. YAGEO products are designed for general purpose applications under normal operation and usage conditions. Please contact YAGEO for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, bo dy or property: Aerospace equipment (artificial satellite, rocket, etc.), Atomic energy -related equipment, Aviation equipment, Disaster prevention equipment, crime prevention equipment, Electric heating apparatus, burning equipment, Highly public informati on network equipment, data -processing equipment , Medical devices, Military equipment, Power generation control equipment, Safety equipment, Traffic signal equipment, Transportation equipment and Undersea equipment, or for any other application or use in w hich the failure of YAGEO products could result in personal injury or death, or serious property damage. Particularly YAGEO Corporation and its affiliates do not recommend the use of commercial, automotive, and/or COTS grade products for high reliability a pplications or manned space flight. Information provided here is intended to indicate product specifications only. YAGEO reserves all the rights for revising this content without further notification, as long as products are unchanged. Any product change will be announced by PCN.