403500000

302719P02 CK-COMPONENTS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

M Thumbwheel & Pushwheel M–3 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com

3 Series

• Most complete product offering in the industr y
• Spacers available to fit most panel cutouts
• Front or rear mounting options Typical Applications
• Test & measurement equipment
• Industrial equipment
• Computer devices Specifications CONTACT RATING: CARRY: 1 AMP continuous. SWITCH: 100 mA max. OPERATING VOLTAGE: 50 mV to 28 V DC or 120 V AC. ELECTRICAL LIFE: 100,000 actuations. CONTACT RESISTANCE: Below 100 m Ω typ. initial @ 2-4 V DC, 100 mA. INSULATION RESISTANCE: 109 Ω min. DIELECTRIC STRENGTH: 500 Vrms min. @ sea level between common terminal and any output. OPERATING TEMPERATURE: -40ºC to 65ºC. Materials HOUSING: ABS plastic. THUMBWHEEL: ABS plastic. ROTOR CONTACTS: Precious metal on copper alloy. STATOR CONTACTS: Hard gold over nickel over copper on epoxy fiberglass. NOTE: Specifications and materials listed above are for switches with standard options For information on specific and custom switches, consult Customer Service Center . * Note: All models listed are RoHS compliant. See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages M–4 thru M–10. For additional options not shown in catalog, consult Customer Service Center. Consult factory for illumination availability. Series

3 Thumbwheel switch

0 Switch section

9 More than 8

0 No seal

1 Sealed contacts

2 Dust lens

3 Sealed contacts & dust lens

11 Decimal, SP , 10 position

14 Resistor decade

21 BCD, 10 position

23 Complement of BCD, 10 position

27 BCD, 10 position

31 BCD, 10 position

71 BCH, 16 position

0 Type 0

1 Type 1, extended type 0

N Solder pins with .100” spacing P Solder pins with .156” spacing

9 Any combination

0 Matte black body, gloss

black wheel, white marking Mounting Style

00 Snap-in, front mount

09 Snap-in, front mount*

10 Rear mount

19 Rear mount*

20 Rear mount

29 Rear mount*

*X9 mounting styles must be ordered with ‘0’ number of sections. ** Note: Termination option N (RoHS compliant) replaced termination option 3 (Non-RoHS compliant). Termination option P (RoHS compliant) replaced termination option B (Non-RoHS compliant).

M Thumbwheel & Pushwheel M–4 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com Available Terminations: 0, 1, N See fig. 1, page M-7. Available Terminations: 1 See fig. 1, page M-7. See fig. 1, page M-7. Available Terminations: 0, 1, N

21 BCD 1-2-4-8; 10 POSITION14 RESISTOR DECADE; 1-2-2-2-2 CODE

(RESISTORS NOT SUPPLIED)

11 DECIMAL–1 POLE; 10 POSITION

9 More than 8 switch sections, specify on CONFIGURATION FORM, page M–10 and consult Customer Service Center. 1-8 Number of switch sections in assembly, includes endplates. 0 Switch section only, no assembly. Blank bodies are considered sections; endplates are not sections. Must be ordered with 09 or 19 mounting style options, see pages M–5 and M–6.

3 THUMBWHEEL SWITCHES

NOTE: Endplates and blank sections available separately, see pages M–13 and M–14. NOTE: For terminal location diagram, see page M-7.

M Thumbwheel & Pushwheel M–5 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com Available Terminations: 0, 1, N See fig. 1, page M-7. Available Terminations: P See fig. 2, page M-7. See fig. 1, page M-7. Available Terminations: 0, 1, N Available Terminations: 0, 1, N See fig. 1, page M-7. N = Number of sections. PANEL MOUNTING

09 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS

(Must be ordered with number of sections option “0”, see Page M–4.) 00 SWITCH ASSEMBLY W/ ENDPLATES–.315 (8,00) SECTION PITCH Type 0 Snap-In Front Mount

23 COMPLEMENT OF BCD 1-2-4-8;

10 POSITION

71 BINARY CODED HEXADECIMAL,

16 POSITION

31 BCD 1-2-4-8; 10 POSITION27 BCD 1-2-4-8; 10 POSITION

NOTE: For terminal location diagram, see page M–7. NOTE: Endplates, blank sections, spacers and assembly hardware available separately, see pages M–8 and M–9. (.315 x N) + .326 DIM. ‘A’ MOUNTING STYLE N = Number of sections. Recommended panel thickness: 0.46-.125 (1,16-3,18)

M Thumbwheel & Pushwheel M–6 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com N = Number of sections. PANEL MOUNTING Mtg. Holes N = Number of sections. (.350 x N) + .560 (.350 x N) + .340 DIM. ‘B’DIM. ‘A’ MOUNTING STYLE N = Number of sections. Recommended panel thickness: 0.46-.125 (1,16-3,18) 20 SWITCH ASSEMBLY W/ ENDPLATES–.350 (8,89) SECTION PITCH

29 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS

(Must be ordered with number of sections option “0”, see Page M–4.)

19 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS

(Must be ordered with number of sections option “0”, see Page M–4.) 10 SWITCH ASSEMBLY W/ ENDPLATES–.350 (8,89) SECTION PITCH Type 1 Rear Mount Type 2 Rear Mount NOTE: Endplates, blank sections, spacers and assembly hardware available separately, see pages M–8 and M–9.

M Thumbwheel & Pushwheel M–7 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com COLOR/MARKING/STOPS SEAL Signal traces cut except for common(s). FIG. 1 FIG. 2

9 ANY COMBINATION OF TERMINATION

CONFIGURATIONS OR SPECIAL TERMINATIONS. P SOLDER PINS WITH .156” SPACING N SOLDER PINS WITH .100” SPACING1 TYPE 1, EXTENDED TYPE 00 TYPE 0

3 SEALED SWITCHING CONTACTS AND DUST LENS

2 DUST LENS. (Protects the character face of the wheel from abrasion and dirt). 1 SEALED SWITCHING CONTACTS. (Sealing is by means of an o-ring rotary seal and a cured-in-place elastomer gasket. Switching contact area is protected from moisture, oil, and airborne contaminants.) 0 UNSEALED SWITCHING CONTACTS. 0 MATTE BLACK HOUSING (Gloss black wheel with white characters; no stops.) PC Board 1/32" (0,79) thick. NOTE: See function codes, pages M–4 and M–5, for signal locations. NOTE: Stop pins are available separately, see page M–8. Dust Lens NOTE: All terminal holes shown may not be pr esent for all function codes, consult Customer Service Center. Terminal connector available for termination options 0 & 1, see page M–9. Specify on configuration form, page M–10 and consult Customer Service Center. Terminal Location Numbers NOTE: Termination option N (RoHS compliant) replaced termination option 3 (Non-RoHS compliant). Termination option P (RoHS compliant) replaced termination option B (Non-RoHS compliant).

M Thumbwheel & Pushwheel M–8 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com Blank sections, Type 0, .315 THK. PART NO.

413602000 W/RIB-BLACK

400502000 W/RIB & W/OUT SPRINGS-BLACK

Blank sections, Front mount, Type 0, .315 THK. PART NO.

413502000 PLAIN-BLACK

400702000 PLAIN & W/OUT SPRINGS-BLACK

PART NO.

400602000 W/RIB-BLACK

400802000 PLAIN-BLACK

Blank sections, Rear mount, Type 1, .350 THK. Blank sections, Rear mount, Type 2, .350 THK. PART NO.

473402000 W/RIB-BLACK

473302000 PLAIN-BLACK

End plates, Front mount, Type 0 PART NO.

413402000 BLACK

PART NO.

400402003 BLACK

End plates, Rear mount, Type 1 End plates, Rear mount, Type 2 Stop pins PART NO.

473202003 BLACK

PART NO.

410802000 BLACK

PART NO. 402900000 Spacers, Front mount, Type 0 & 3, .078 THK. (Makes section pitch 10mm) Two required for complete assembly. Two required for complete assembly. 4734 4733 4006 4008 Two required for complete assembly.

M Thumbwheel & Pushwheel M–9 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com PART NO. 605A00000 PC 605A02000 SOLDER LUG Fits 0 & 1 terminations only. Terminal connector PART NO. 403500000 Nut Two nuts required per assembly and screws. Screws for field assembly of thumbwheel switches (2 screws needed per assembly + 403500000 nuts) 605A00000 605A02000 PART NO. 406100652 Nut driver (For 403500000 nut) 1–2 1–2 3–4 3 5–7 4–6 412700000 412701000 412702000 NUMBER OF SECTIONS IN ASSEMBLY FRONT MOUNTING REAR MOUNTING MTG. STYLE – 00 MTG. STYLE – 10 SCREW PART NUMBER (0-80 UNF THD. SIZE)

M Thumbwheel & Pushwheel M–10 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change www.ck-components.com QUALITY CONTROL INSTRUCTIONS PRODUCTION APPROVAL DATE C&K PART NUMBER REV. INITIALS DATE CATALOG PART NO. COMPANY NAME CUSTOMER PRINT REVISION:ADDRESS TEL.# CUSTOMER CONTACT DATE ORIGINATED BY SALES REP. DETAILS: Q.C. APPROVAL DATE Configuration Form GRAY SHADED AREAS TO BE FILLED IN BY CUSTOMER SERVICE. C&K PARTNUMBER THUMBWHEEL SECTIONS DESCRIBE IN APPROPRIATE ROW SPECIAL INSTRUCTIONS OR SPECIFICATIONS: 3 – FUNCTION CODE – TERMINATIONS– COLOR/MARKING/STOPS/SEAL – ILLUMINATION FOR SWITCHES WITH MORE THAN 11 SECTIONS, CONTINUE ON ADDITIONAL SHEETS. ENTER OPTION CODES IN APPROPRIATE BOXES. FUNCTION CODES INCLUDE BLANK SECTIONS (SEE PAGES M-9 & M-10). NO. OF SEC. – – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– – 3 –– –