3652

3650 BURR-BROWN | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

FEATURES

l LARGE COMMON-MODE VOLTAGES: ±2000V Continuous 140dB Rejection l ULTRA LOW LEAKAGE: 0.35µA max at 240V/60Hz 1.8pF Leakage Capacitance l EXCELLENT GAIN ACCURACY: 0.05% Linearity 0.05%/1000 Hrs Stability l WIDE BANDWIDTH: 15kHz ±3dB 1.2V/µs Slew Rate

APPLICATIONS

l INDUSTRIAL PROCESS CONTROL l DATA ACQUISITION l INTERFACE ELEMENT l BIOMEDICAL MEASUREMENTS l PATIENT MONITORING l TEST EQUIPMENT l CURRENT SHUNT MEASUREMENT l GROUND-LOOP ELIMINATION l SCR CONTROLS

DESCRIPTION

The 3650 and 3652 are optically coupled integrated circuit isolation amplifiers. Prior to their introduction commercially available isolation amplifiers had been modular or rack mounted devices using transformer coupled modulation demodulation techniques. Compared to these earlier isolation amplifiers, the 3650 and 3652 have the advantage of smaller size, lower cost, wider bandwidth and integrated circuit reliability. Also, because they use a DC analog modu- lation technique as opposed to a carrier-type tech- nique, they avoid the problems of electro- magnetic interference (both transmitted and received) that most of the modular isolation amplifiers exhibit. A 1 A 1 Light Flux Coupling 23A 3 A 4 1.6MΩ 1.6MΩ R G1 R G2 R IN

3652 Only Common to 3650 and 3652

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 © 1976 Burr-Brown Corporation PDS-342L Printed in U.S.A. August, 1997 SBOS129

At +25°C and ±15VDC supply voltages, unless otherwise specified. 106 106 R G1 + RG2 + RIN R G1 + RG2 + RIN + RO 25Ω 90Ω ±30Ω PRODUCT 3650MG, HG (1) 3650JG 3650KG 3652MG, HG (1) 3652JG ISOLATION Isolation Voltage Rated Continuous, min 2000Vp or VDC Tested Voltage, min, 10s Duration 5000Vp Isolation Mode Rejection, G = 10 DC 140dB 60Hz, 5000Ω Source Unbalance 120dB Leakage Current, 240V/60Hz 0.35 µA, max Isolation Impedance Capacitance 1.8pF Resistance 10 12Ω GAIN Gain Equation for Current Sources G 1 = 106V/Amp G 1 = 1.0057 x 106V/Amp (2) for Voltage Sources G V1 = V/V V/V Input Resistance, RIN, max 25 Ω Buffer Output Impedance, RO Not Applicable Gain vs Temperature 300ppm/ °C 100ppm/ °C 50ppm/ °C 300ppm/ °C 200ppm/ °C Gain vs Time ±0.05%/1000hrs ±0.05%/1000hrs Frequency Response Slew Rate 0.7V/µs min, 1.2V/µs typ ±3dB Frequency 15kHz Settling Time to ±0.01% 400µs to ±0.1% 200µs INPUT STAGE (5) Input Offset Voltage at 25°C, max(3) ±5mV ±1mV ±0.5mV ±5mV ±2mV vs Temperature, max ±25µV/°C ±10µV/°C ±5µV/°C ±50µV/°C ±25µV/°C vs Supply 100 µV/V 100 µV/V vs Time 50 µV/1000hrs 100 µV/1000hrs Input Bias Current at 25°C 10nA typ, 40nA max 10pA typ, 50pA max vs Temperature 0.3nA/ °C Doubles Every +10 °C vs Supply 0.2nA/V 1pA/V Input Offset Current 10pA vs Temperature Effects Included Doubles Every +10 °C vs Supply In Output Offset 1pA/V Input Impedance Differential “R IN” = 25Ω max 10 11Ω Common-Mode 10 9Ω 1011Ω Input Noise Voltage, 0.05Hz to 100Hz 4 µVp-p 8 µVp-p 10Hz to 10kHz 4 µVrms 5 µVrms Input Voltage Range Common-Mode, Linear Operation, ±(|V| –5)V ±(|V| –5) w/o damage, at +, – ±V ±V at +I, –I Not Applicable (6) ±300V for 10ms(7) at +IR , –IR Not Applicable(6) ±3000V for 10ms(7) Differential, w/o damage, at +, – ±V ±V Differential, w/o damage, at +I, –I Not Applicable ±600V for 10ms(7) Differential, w/o damage, at +IR , –IR Not Applicable ±6000V for 10ms(7) Common-Mode Rejection, 60Hz 90dB at 60Hz, 5k Ω Imbalance 80dB at 60Hz, 5k Ω Imbalance Power Supply (Input Stage Only) Voltage (at “+V” and “–V”) ±8V to ±18V ±8V to ±18V Current Quiescent ±1.2mA(8) ±3mA (8) with ±10V Output(7) +6.5mA or –6.5mA, typ +8.5mA or –8.5mA, typ +12mA or –12mA, max +16mA, or –16mA, max

1.6MΩ 1.6MΩ R O R O Gain Adj Gain Adj 81 1 13 14 15 1612109 32 29 C C Bal +V CC –VCC Bal 3652 13 14 15 16 32 29 C C Bal +V CC –VCC Bal 3650 SPECIFICATIONS (CONT) At +25°C and ±15VDC supply voltages, unless otherwise specified. PRODUCT 3650MG, HG (1) 3650JG 3650KG 3652MG, HG (1) 3652JG OUTPUT STAGE Output Voltage, min ±10V ±10V Output Current, min ±5mA ±5mA Output Offset Voltage at 25°C, max (3) ±25mV ±10mV ±10mV ±25mV ±10mV vs Temperature, max ±900µV/°C ±450µV/°C ±300µV/°C ±900µV/°C ±450µV/°C vs Supply ±500µV/V ±500µV/V vs Time ±1mV/1000hrs ±1mV/1000hrs Output Noise Voltage 0.05Hz to 100Hz 50 µVp-p 50 µVp-p 10Hz to 1kHz 65 µVrms 65 µVrms Power Supply (Output Stage Only) Voltage (“+VCC ” and “–VCC ”) ±8V to ±18V Current Quiescent ±2.3mA typ, ±6mA max with ±5mA Output, max ±11mA TEMPERATURE (9) Specification 0°c to +85°C Operating –40°C to +100°C Storage –40°C to +125°C NOTES: (1) All electrical and mechanical specifications of the 3650MG and 3652MG are identical to the 3650HG and 3652HG, respectively, except that the following specifications apply to the 3650MG and 3652MG: (a) Isolation test voltage duration increased from 10 seconds minimum to 60 seconds minimum; (b) Input offset voltage at 25°C, max: ±10mV; vs temperature max: ±100µV/°C; (c) Output offset voltage at 25°C, max; ±50mV; vs temperature max; ±1.8mV/°C. (2) If used as 3650, see stage specifications at +I and –I inputs for 3652 unless otherwise noted. (6) Maximum safe input current at either input is 10mA. (7) Continuous rating is 1/3 pulse rating. (8) Load current is drawn from one supply lead at a time: other supply current at quiescent level. For 3652 add 0.2mA/V of positive CMV. (9) dT/dt < 1°C/minute below 0°C, and long-term storage above 100°C is not recommended. Also limit the repeated thermal cycles to be within the 0°C to +85°C temperature range. PIN CONFIGURATIONS PACKAGE INFORMATION PACKAGE DRAWING PRODUCT PACKAGE NUMBER (1) 3650 32-Pin DIP 77 3652 32-Pin DIP 77 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degrada- tion to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.

Frequency (kHz) Gain Error (dB) 3031 0 Gain = 1 Gain = 100 DISTORTION vs FREQUENCY Frequency (kHz) 0.1 0.1 10 313

0.3 Distortion (%)

VOUT = +10V R L = 2kΩ REJECTION vs RESISTOR IMBALANCE Input Resistor Imbalance 01 0.25 0.50 0.75 160 120 Rejection (dB) R G1 R G1 + RG2 or R G2 R G1 + RG2 IMR 60Hz CMR 60Hz G =100 G =100 G =100 G =1 G =1G =136523650 3650 3652 NORMALIZED LINEARITY vs TEMPERATURE Temperature (°C) –25 1.5 1.4 1.3 1.2 1.1 Relative Nonlinearity 0 2 55 07 5 1 0 0 ISOLATION LEAKAGE CURRENT vs ISOLATION VOLTAGE Isolation Voltage (kV) Leakage Current µA AC or 100s pA, DC 06 24 135 Typ at 60Hz Typ at DC INPUT STAGE SUPPLY CURRENT vs OUTPUT VOLTAGE Output Voltage (V) Supply Current (mA) –15 15 –5 5 –10 0 10 Add 2mA typ, 4mA max for 3652 at V– at V+ Max at 70°C Max at 25°C Typ at 70°C Typ at 25°C Typ at 25°C 3mA 1.2mA TYPICAL PERFORMANCE CURVES Typical at +25°C and ±15VDC power supplies, unless otherwise noted.

OUTPUT VOLTAGE AND GAIN ERROR vs TIME Time of Operation (Hours) 100 100K Estimated Output Swing (+V) 1k 10k 0.5 0.1 0.05 Gain Error Change (%) 70°C 70°C 25°CGain Error Change 140 120 100 1 10 100 1000 Gain

3652 COMMON-MODE AND

ISOLATION-MODE REJECTION vs GAIN Rejection (dB) Isolation-mode Rejection Common-mode Rejection DC at I or I R pins 60Hz at I pins 60Hz at IR pins 60Hz at IR pins DC at I or IR pins 60Hz at I pins 140 120 100 1 10 100 1000 Gain

3650 COMMON-MODE AND

ISOLATION-MODE REJECTION vs GAIN Rejection (dB) Isolation-mode Rejection Common-mode Rejection DC 60Hz 60Hz DC OUTPUT VOLTAGE SWING vs INPUT SUPPLY VOLTAGE Input Supply Voltage (V) 52 0 Output Voltage (V) 10 15 Typ at 25°C 25°C 70°C Guaranteed Min at Output Supply ±15V PHASE SHIFT vs FREQUENCY Frequency (kHz) –200 0.3 –40 –80 –120 –160 Phase Shift (Deg) 3013 1 0 Gain 1 to 100 TYPICAL PERFORMANCE CURVES (CONT) Typical at +25°C and ±15VDC power supplies, unless otherwise noted. REJECTION vs FREQUENCY Frequency (kHz) 0.1 140 120 100 Rejection (dB) 0.3 1 3 10 30 IMR CMR Supply Voltage Gain = 100 3650 3652

OUT Þ Δ VOUT /ΔT, EOSI Þ ΔEOSI/ΔT, etc. variations must also be considered. noise sources and are therefore omitted. FIGURE 6c. 3652 with Differential Voltage Sources. FIGURE 7. DC Error Analysis Model for 3650.

106 EOSI

have been omitted for simplicity. Refer to Figure 5 for details.

106 IOS

amplifiers in SCR control application. FIGURE 9. 3652 Used in Patient Monitoring Application (ECG, VCG, EMG Amplifier).

FIGURE 10. 3-Phase Bidirectional SCR Control with Voltage Feedback.

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright  2000, Texas Instruments Incorporated