358733-000 MACOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

8ElectricalInterconnectProducts 8-39 Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators

Applications

Used for terminating wires to component terminals, such as motor tabs, con- nector pins, and switch terminals. Product selection process 1. Determine the application operating temperature. 2. From the Product Options table on the next page, select the product series appropriate for the appli- cation, based on the tem- perature required. 3. Determine your compo- nent connection point type (pin, post, or tab) and dimensions. 4. Determine your wire gauge. 5. Optional: Select tape carrier center-to-center spacing (D-71X series only). This should match center spacing of com- ponent terminals. 6. Select part number from the appropriate table: I For CWT series (applications with low- temperature wires— below 125°C [257°F]), use Table A. I For D-129/141/71X series (applications with wires rated higher than 125° C [257°F]), use Table B. Installation For proper installation of these devices, the correct heating tool and reflector attachment must be used. Either of the following Raychem heating tools are recommended: I HL1802E I AA-400 Super Heater Refer to Raychem installa- tion procedure RCPS 200- 12 (for D-129, D-141, D-71X) or RPIP 824-00 (for CWT) for detailed instructions and recommended reflector attachment. You will find ordering infor- mation for these tools see section 10. Product Facts I Transparent polyvinylidene fluoride or polyolefin insulation sleeve provides encapsulation, inspectability, strain relief, and insulation I Prefluxed solder preform offers a controlled soldering process I One-piece design means easy installation and low installed cost I Optional tape carrier provides convenience and ease of installation I UL and CUL Recognized R Available in: Americas I Europe I Asia Pacific I

Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators (Continued) Connection-point Type and Size Terminal Dimensions Wire AWG/mm 2 Part No. W = up to 0.63 [.025] 24 [0.24] CWT-1501 20 [0.61] CWT-1502 W = 0.63 [.025] to 24 [0.24] CWT-1501 20 [0.61] CWT-1503 Product Series Max. Operating Temperature Min. Wire Temperature Rating Note: C admium-free option (B-152 series) is available for operating temperature of 125˚C [257˚F]. C onsult Tyco Electronics for details. Product Options Table A. CWT Series (125°C [257°F] rated) pin W post W tab W

8ElectricalInterconnectProducts 8-41 Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators (Continued) Wire Tape Carrier Spacing of Sleeves (Center-to-Center) W = up to 0.61 [.024] 1.27 [.050] Part Inside Diameter Fully No.* As Supplied** Recovered† Length†† Note: Micro SolderSleeve terminators are used for attaching leads smaller than 26 AWG (0.15 mm2)to terminals less than 0.6 [.025] wide. *The D-110 series sleeves are primarily for single wire terminations and do not have a wire stop. The D-141 series will accept either one or two wires; the parts have a built-in wire stop that will locate the wire approximately 0.76 [0.03] from bottom of terminal. **Minimum. Wire insulation must be smaller than this. When using the D-141 parts for two-wire terminations, the com- bined wire insulation diameters must be less than 1.5 [.060]. †Maximum. The combination of conductor diameter and terminal width and the wire insulation must be greater than this. ††The terminal length should be at least 1.2 [0.05] shorter than this. The wire strip length must be adjusted so that, when terminated, the exposed conductor is covered by the sleeve. pin W post W tab W For Fine Wire Terminations 0.15 mm2 (26 AWG) and Smaller* Table B. D-129/141/71X Series (up to 150°C [302°F] rated) Connection-point Type and Size

Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators (Continued) Material Insulation [D-129, D-141, D-71X] Radiation-crosslinked, heat-shrinkable polyvinylidene fluoride Insulation [CWT] Radiation-crosslinked, heat-shrinkable polyolefin Solder and flux [D-129, D-141, D-71X] Solder: Sn63 Pb37 Flux: ROL1 per ANSI -J - 004 [RMA flux] Solder and flux [CWT] Solder: Sn50 Pb32 Cd 18 Flux: ROM1 per ANSI -J - 004 [RA flux] Typical Performance Voltage drop 2.0 mV Tensile strength Exceeds strength of conductor D ielectric strength 2.0 kV Temperature rating [CWT] -55°C to 125°C [-67°F to 257°F] Temperature rating [D-129, D-141, D-71X] -55°C to 150°C [-67°F to 302°F] Insulation resistance 1000 megohms Series Agency Raychem CWT UL and CUL E87681 D-5023 D-129, D-141 UL and CUL E87681 RT-1404 Product Characteristics Specifications/Approvals