UPC3533 NEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. © 2002 BIPOLAR ANALOG INTEGRATED CIRCUIT µµµµPC3533,3504 THREE-THERMAL POSITIVE OUTPUT VOLTAGE DATA SHEET Document No. G15965EJ2V0DS00 (2nd edition) Date Published July 2002 NS CP(K) Printed in Japan The mark # shows major revised points.

DESCRIPTION

The µPC3533 and 3504 are three-thermal positive output voltage regulators with an output current of 1 A at respective output voltages of 3.3 and 4 V. These regulators are guaranteed to operate at as low as −40°C.

FEATURES

  • Output current capacity: 1 A
  • On-chip overcurrent limiter
  • On-chip output transistor safe operation area protection
  • On-chip thermal protection
  • Output capacitor capacitance: 0.1 µF or higher
  • Wide operating temperature range: T A = −40 to +85°C PIN CONFIGURATION (Marking Side) µPC3533HF, 3504HF: MP-45G 1: INPUT Marking 3: OUTPUT 2: GND BLOCK DIAGRAM GND OUTPUT INPUT Startup circuit Thermal shut down Reference voltage circuit Error Amp. Safe operation area protection Overcurrent protection Constant current source

ORDERING INFORMATION

Part Number Package Outputs Marking Packing Type µ PC3533HF MP-45G (Isolated TO-220) 3.3 V 3533 • Bag stuffing µ PC3540HF MP-45G (Isolated TO-220) 4.0 V 3504 • Bag stuffing

µµµµPC3533, 3504 ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise specified) Parameter Symbol Rating Unit Input Voltage V IN −0.3 to +25 V Internal Power Dissipation (TC = 25°C) P T 15 Note W Operating Ambient Temperature T A −40 to +85 °C Operating Junction Temperature T J −40 to +150 °C Storage Temperature T stg −55 to +150 °C Thermal Resistance (junction to case) R th(J-C) 7° C / W Thermal Resistance (junction to ambient) R th(J-A) 65 °C/W Note Internally limited. When the operating junction temperature rises over 150 °C, the internal circuit shuts down the output voltage. Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. TYPICAL CONNECTION D 2 D 1 C IN C OUT INPUT OUTPUTPC3533, 3504µ CIN: 0.1 to 0.47 µF or higher. Set this value according to the length of the line between the regulator and INPUT pin. Be sure to connect C IN to prevent parasitic oscillation. Use of a film capacitor or other capacitor with excellent voltage and temperature characteristics is recommended. If using a laminated ceramic capacitor, it is necessary to ensure that C IN is 0.1 µF or higher for the voltage and temperature range to be used. COUT: 0.1 µF or higher. Be sure to connect C OUT to prevent oscillation and improve excessive load regulation. Place C IN and COUT as close as possible to the IC pins (within 2 cm). Also, use an electrolytic capacitor with low impedance characteristics if considering use at sub-zero temperatures. D1: If the OUTPUT pin has a higher voltage than the INPUT pin, connect a diode. D2: If the OUTPUT pin has a lower voltage than the GND pin, connect a Schottky barrier diode. Caution Make sure that no voltage is applied to the OUTPUT pin from external.

Data Sheet G15965EJ2V0DS 3 µµµµPC3533, 3504 RECOMMENDED OPERATING CONDITIONS Parameter Symbol Type Number MIN. TYP. MAX. Unit Input Voltage V IN µ PC3533 5.8 20 V µ PC3504 6.5 20 V Output Current I O All 0.005 1 A Caution Use of conditions other than the above-listed recommended operating conditions is not a problem as long as the absolute maximum ratings are not exceeded. However, since the use of such conditions diminishes the margin of safety, careful evaluation is required before such conditions are used. Moreover, using the MAX. value for all the recommended operating conditions is not guaranteed to be safe.

µµµµPC3533, 3504

ELECTRICAL CHARACTERISTICS

µµµµPC3533 (TJ = 25°°°°C, VIN = 5.8 V, IO = 0.5 A, CIN = 0.33 µµµµF, COUT = 0.1 µµµµF, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. MAX. Unit Output Voltage V O1 3.168 3.3 3.432 V VO2 5.8 V ≤ VIN ≤ 20 V, 5 mA ≤ IO ≤ 1 A 3.135 3.465 V Line Regulation REG IN1 5.8 V ≤ VIN ≤ 20 V 20 50 mV REGIN2 5.8 V ≤ VIN ≤ 9 V 10 30 mV Load Regulation REG L1 5 mA ≤ IO ≤ 1 A 20 50 mV REGL2 250 mA ≤ IO ≤ 750 mA 10 20 mV Quiescent Current I BIAS 2.8 6 mA Quiescent Current Change ∆IBIAS1 5.8 V ≤ VIN ≤ 20 V 1.0 mA Output Noise Voltage V n 10 Hz ≤ f ≤ 100 kHz 55 µ Vr.m.s. Ripple Rejection R•R f = 120 Hz, 5.8 V ≤ VIN ≤ 9 V 57 dB Dropout Voltage V DIF IO = 1 A 2.0 2.5 V Short Circuit Current I Oshort1 VIN = 5.8 V 1.8 A Peak Output Current I Opeak VIN = 10 V 1.0 2.1 2.8 A Temperature Coefficient of ∆VO/ ∆TI O = 5 mA, 0°C ≤ TJ ≤ 125°C − 0.4 mV/ °C Output Voltage µµµµPC3504 (TJ = 25°°°°C, VIN = 6.5 V, IO = 0.5 A, CIN = 0.33 µµµµF, COUT = 0.1 µµµµF, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. MAX. Unit Output Voltage V O1 3.84 4.0 4.16 V VO2 6.5 V ≤ VIN ≤ 20 V, 5 mA ≤ IO ≤ 1 A 3.80 4.20 V Line Regulation REG IN1 6.5 V ≤ VIN ≤ 20 V 20 50 mV REGIN2 6.5 V ≤ VIN ≤ 10 V 10 30 mV Load Regulation REG L1 5 mA ≤ IO ≤ 1 A 20 50 mV REGL2 250 mA ≤ IO ≤ 750 mA 10 20 mV Quiescent Current I BIAS 2.8 6 mA Quiescent Current Change ∆IBIAS1 6.5 V ≤ VIN ≤ 20 V 1.0 mA Output Noise Voltage V n 10 Hz ≤ f ≤ 100 kHz 55 µ Vr.m.s. Ripple Rejection R•R f = 120 Hz, 6.5 V ≤ VIN ≤ 10 V 60 dB Dropout Voltage V DIF IO = 1 A 2.0 2.5 V Short Circuit Current I Oshort1 VIN = 6.5 V 1.8 A Peak Output Current I Opeak VIN = 10 V 1.1 2.1 2.8 A Temperature Coefficient of ∆VO/ ∆TI O = 5 mA, 0°C ≤ TJ ≤ 125°C − 0.4 mV/ °C Output Voltage

Data Sheet G15965EJ2V0DS 5 µµµµPC3533, 3504 TYPICAL CHARACTERISTICS (Reference Values) 1.92 05 0 25 100 125 75 150 TA - Operating Ambient Temperature - °C PD - Total Power Dissipation - W 85°C PD vs. TA Without heatsink With infinite heatsink With 10 °C/W heatsink VO - Output Voltage - V 4.0 3.0 2.0 1.0 43216 58 71 0 9 VO vs. VIN ( PC3533) VIN - Input Voltage - V µ IO = 0.5 A IO = 1.0 A IO = 5 mA TJ = 25°C 1.0 2.0 3.0 4.0 5.0 43216 58 71 0 90 VO - Output Voltage - V VO vs. VIN ( PC3504) VIN - Input Voltage - V µ IO = 0.5 A IO = 1.0 A IO = 5 mA TJ = 25°C 1.0 2.0 3.0 0.5 1.5 2.5 43216 58 71 0 9 IBIAS - Quiescent Current - mA IBIAS vs. VIN ( PC3533) VIN - Input Voltage - V µ IO = 0.5 A IO = 1.0 A TJ = 25°C IO = 5 mA 1.0 0.5 1.5 2.0 2.5 3.0 43216 58 71 0 90 IO = 0.5 A IO = 5 mA TJ = 25°C IO = 1.0 A IBIAS - Quiescent Current - mA IBIAS vs. VIN ( PC3504) VIN - Input Voltage - V µ −25 −50 0 100 50 150−50 PC3504µ PC3533µ IO = 5 mA ∆VO - Output Voltage Deviation - mV ∆VO vs. TJ TJ - Operating Junction Temperature - °C

µµµµPC3533, 3504 100 0 100 1000 10000 10000010 PC3533µ IO = 0.5 A PC3504µ R.R - Ripple Rejection - dB R.R vs. f f - Frequency - Hz 2.5 51 01 5 2 5 1.5 0.5 0 20 TJ = 25°C IOpeak - Peak Output Current - A IOpeak vs. VDIF ( PC3504) VDIF - Dropout Voltage - V µ 2.5 51 01 5 2 5 1.5 0.5 0 20 TJ = 25°C IOpeak - Peak Output Current - A IOpeak vs. VDIF ( PC3533) VDIF - Dropout Voltage - V µ PC3533 PC3504 µ µ TJ = 25°C , f = 120 Hz PC3504: 6.5 V ≤ VIN ≤ 10 Vµ PC3533: 5.8 V ≤ VIN ≤ 9 Vµ R.R - Ripple Rejection - dB R.R vs. IO IO - Output Current - A 2.5 1.5 0.5 TJ = 25°C VDIF - Dropout Voltage - V VDIF vs. IO IO - Output Current - A 2.5 1.5 0.5 −50 −25 100 125 50 75250 IO = 0.5 A IO = 1.0 A IO = 0.1 A VDIF - Dropout Voltage - V VDIF vs. TJ ( PC3533) TJ - Operating Junction Temperature - °C µ

Data Sheet G15965EJ2V0DS 7 µµµµPC3533, 3504 2.5 1.5 0.5 50 25 100 125 50 75250 IO = 0.5 A IO = 1.0 A IO = 0.1 A VDIF - Dropout Voltage - V VDIF vs. TJ ( PC3504) TJ - Operating Junction Temperature - °C µ

µµµµPC3533, 3504 PACKAGE DRAWING µPC3533HF, 3504HF 3PIN PLASTIC SIP (MP-45G) D 17.0 ±0.3 NOTE Each lead centerline is located within 0.25 mm of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS P3HF-254B-4 G 0.25 H 2.54 (T.P.) A 10.0 ±0.2 I 5.0 ±0.3 U 2.4 ±0.5 V Y 8.9 ±0.7 Z 1.30 ±0.2 J K L 8.5 ±0.2 B 7.0 ±0.2 C 1.50 ±0.2 E F 0.75 ±0.10 M 8.5 ±0.2 N P 2.8 ±0.2 3.3±0.2φ 2.46±0.2 5.0±0.2 4.5±0.2 0.65±0.10 13 2 M A B E I D L M K Y JH C FG Z N P UV

Data Sheet G15965EJ2V0DS 9 µµµµPC3533, 3504 RECOMMENDED MOUNTING CONDITIONS The following conditions must be met for mounting conditions of the µPC3533, 3504. For more details, refer to the Semiconductor Device Mounting Technology Manual (C10535E). Please consult with our sales offices in case other mounting process is used, or in case the mounting is done under different conditions. Type of Through-hole Device µµµµPC3533HF, 3504HF: MP-45G Process Conditions Wave Soldering (only to leads) Solder temperature: 260°C or below, Flow time: 10 seconds or less Partial Heating Method Pin temperature: 300°C or below, Heat time: 3 seconds or less (Per each pin). Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered.

µµµµPC3533, 3504 REFERENCE DOCUMENTS Document Name Document No. Usage of Three-Terminal Regulators User’s Manual G12702E Review of Quality and Reliability Handbook Information C12769E NEC Semiconductor Device Reliability/Quality Control System Information C10983E Semiconductor Device Mounting Technology Manual Information C10535E SEMICONDUCTOR SELECTION GUIDE - Products and Packages- X13769X M8E 00. 4 The information in this document is current as of July, 2002. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard":Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above).