32D UNSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 6

Technical content

Features

Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.1/5 32D Series Radial Lead Varistor (MOV) Material General Characteristics Definition Part Numbering The 32D series radial leaded varistors provides an ideal circuit protection solution for lower DC voltage applications by offering higher surge ratings than ever before available in such small discs. The maximum peak surge current rating can reach up to 30KA (8/20 μs pulse) to protect against high peak surges, including indirect lightning strike interference, system switching transients and abnormal fast transients from the power source.  Wide operating voltages ranging from 130Vrms to 1100Vrms(AC)  Fast response time of less than 25ns, instantly clamping the transient over voltage.  High surge current handling capability.  High energy absorption capability.  Low clamping voltages, providing better surge protection  Low capacitance values, providing digital switching circuitry protection.  High insulation resistance, preventing electric arching to the adjacent devices or circuits.  Transistor, Diode, IC, Thyristor or Triac semiconductor protection.  Surge protection in consumer electronics.  Surge protection in industrial electronics.  Surge protection in electronic home appliances, gas and petroleum appliances.  Relay and electromagnetic valve surge absorption.  Coating: Epoxy Resin  Lead Wire: The Copper Wire  Electrode: Silver Solder  Disk: Zinc Oxide (1) Size(mm) : 05mm to 32mm (2) Type : D: Disk, S: Square (3) Varistor Voltage : 470(47*10 0=47V) , 471 47*101=470V) (4) Tolerance : K±10%, L±15%, M±20% (5) Surge Current Standardğ J:High Surge (6) Taping Mode : TR : Reel (7) Lead Form : C:Crimped, Short leg : NO : X.X (8) Coating : H:Epoxy Coating 125 Note: (5)a(6)a(7)a(8) options is non-standard  Operating Temperature: -40℃ ~ +85℃  Storage Temperature: -40℃ ~ +125℃  Working Surface Temperature: +115℃  Insulation Resistance: > 100MΩ  Coating (Epoxy Resin): Flame-Retardant to UL 94V-0  Approval Standard and File Numberğ ULğE489912 32 - D - XXX - K - X - X - X - X

Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Radial Lead Varistor (MOV) Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Electrical Characteristics (@ 25℃ Unless Otherwise Specified ) 32D201K 32D221K 32D241K 32D271K 32D301K 32D331K 32D361K 32D391K 32D431K 32D471K 32D511K 32D561K 32D621K 32D681K 32D751K 32D781K 32D821K 32D911K 32D102K 32D112K 32D122K 32D142K 32D162K 32D182K 130 140 150 175 190 210 230 250 275 300 320 350 385 420 460 485 510 550 625 680 750 880 1000 1100 170 180 200 225 250 275 300 320 350 385 415 460 505 560 615 640 670 745 825 895 990 1140 1280 1465 200(185-225) 220(198-242) 240(216-264) 270(243-297) 300(270-330) 330(297-363) 360(324-396) 390(351-429) 430(387-473) 470(423-517) 510(459-561) 560(504-616) 620(558-682) 680(612-748) 750(675-825) 780(702-858) 820(738-902) 910(819-1001) 1000(900-1100) 1100(990-1210) 1200(1080-1320) 1400(1260-1540) 1600(1400-1760) 1800(1620-1980) 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 275 297 319 330 363 396 418 440 473 506 561 594 627 660 682 726 770 825 858 891 1001 1056 1122 1188 250 270 290 300 330 360 380 400 430 460 510 540 570 600 620 660 700 750 780 810 910 960 1020 1080 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 25000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 340 360 395 455 505 550 595 650 710 775 345 920 1025 1120 1240 1290 1355 1500 1650 1815 1980 2310 2475 2970 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 Part Number 32D201KJ 32D221KJ 32D241KJ 32D271KJ 32D301KJ 32D331KJ 32D361KJ 32D391KJ 32D431KJ 32D471KJ 32D511KJ 32D561KJ 32D621KJ 32D681KJ 32D751KJ 32D781KJ 32D821KJ 32D911KJ 32D102KJ 32D112KJ 32D122KJ 32D142KJ 32D162KJ 32D182KJ Maximum Allowable Voltage Rated Power Varistor Voltage V1mA (V) Withstanding Surge Current 8/20μS Max Clamping Voltage VDC (V) VAC (V) VC (V) IP (A) (W)Standard High Surge I(A) Standard I(A) High Surge (J) Standard (J) High Surge Maximum Energy (10/1000μs) time time 32D Series

Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Radial Lead Varistor (MOV) Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.3/5 ROHS Packaging Information Part Marking Package Dimensions Unit: mm 32D Series VDE 32DXXXX Marking Trademark Part No. Standard for Safety UN logo 32DXXXK UL / VDE Dimension Part No. Bag Small Carton Carton Unit:Pcs 32D 201K to 182K 100 500 1000 TABLE1 Symbol H(max.) L(min.) D(max.) D1(±0.8) T(max.) d(±0.05) 39.0 25.0 34.0 10.0 TABLE2 1.2 Dimension TABLE2 Model 201K 221K 241K 271K 301K 331K 361K 391K 431K 471K 511K 561K 621K 681K 751K 781K 821K 911K 102K 112K 122K 142K 162K 182K 4.1 4.2 4.3 4.5 4.7 4.8 5.0 5.1 5.3 5.6 5.8 6.2 6.4 6.4 6.5 6.8 7.2 7.6 7.8 8.5 11.0 11.5 12.0 12.5 T(max.) Model T(max.) D T L d k≤3.0 H

Radial Lead Varistor (MOV) Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.4/5 Reliability Test (Mechanical Ratings) ROHS 32D Series Test Parameter Terminal Pull Strength Soldering-solder ability Soldering-Resistance to Solder Heat After preheating the specimen, the specimen shall be completely immersed into a soldering bath having a temperature of 260±5℃ for 10±1 (D5: 5±1) seconds or iron of 400±5℃ for 3±0.5 seconds. There after the change of Vb and mechanical damage shall be examined. After dipping the terminal to depth of approximately 3mmfrom the specimen in a soldering bath of 260℃ for 10±1(D5: 5±1) seconds. Thereafter the terminal shall be visually examined. The Specimen shall be vibrated by its lead wires with a total amplitude of 1.5mm and a varying frequency of10~55~10HZ(each minutes) for a period of 2 hours respectively in each X,Y and Z directions. The unit shall be secured with its terminal kept vertical and the weight specified below be applied in the axial direction. The terminal shall gradually be bent by 90° in one direction, then 90° in the opposite direction, and again back to the original position. The damage of the terminal shall be visually examined. After gradually applying the load specified below and keeping the unit fixed for ten seconds, the terminal shall be visually examined for any damage No visible damage No visible damage Terminations shall be uniformly tinned No visible damage ¶VB/VB%⛄±5% No visible damage ¶VB/VB%⛄±5% Terminal Bending Strength Vibration Test Condition / Description Performance Requirements Diameter 0.6mm 0.8mm 1.0mm Diameter 0.6mm 0.8mm 1.0mm Loading 1.0 Kg 1.0 Kg 2.0 Kg Loading 0.5 Kg 0.5 Kg 1.0 Kg

Radial Lead Varistor (MOV) Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.5/5 Reliability Test (ENVIRONMENTAL RATINGS) ROHS 32D Series Test Parameter Dry Heat Loading Temperature Cycle Surge Lifetime Rating Voltage Proof The change of Vb shall be measured after the impulse listed below is applied 10,000 times continuously with the interval of ten seconds at room temperature.Vb and mechanical damage shall be examined. Voltageğ2500VAC Leakage Current⛄0.5mA Timeğ60 Seconds Condition the specimen to each temperature form step 1 to step 4 in this order for the period shown in the table of specifications. The change of Vb and mechanical damage shall be examined after 2 hours. The Specimen shall be vibrated by its lead wires with a total amplitude of 1.5mm and a varying frequency of 10~55~10HZ(each minutes) for a period of 2 hours respectively in each X,Y and Z directions. In a drying oven without load. Ambient tempğ125±2℃ ; periodğ1000±24hours The specimen shall be applied continuously the maximum allowable voltage at the specified conditions for specified period and then stored at room temperature and normal humidity over 2 hours. Thereafter, the change of Vb and mechanical damage shall be examined.Ambient tempğ125±2℃ ; Periodğ1000±24hours ¶VB/VB%⛄±5% ¶VB/VB%⛄±10% ¶VB/VB%⛄±10% No visible damage ¶VB/VB%⛄±10% No Breakdown No visible damage ¶VB/VB%⛄±10% High Temperature Storage Damp Heat Loading Test Condition / Description Performance Requirements Step Temp℃ -40+3℃ Room Temp 85+2℃ Room Temp Period 30 min. 15 min. 30 min. 15 min.

Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Disclaimer ROHS UNSEMI RESERVES THE RIGHT TO MAKE CHANGE ON OUR PRODUTS , PRODUCTS SPECIFICATION AND DATA WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. UN SEMICONDUCTOR LIMITED its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “UNSEMI”)does not give any representations or warranties for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. In no event shall UNSEMI be liable for any indirect, incidental, punitive, special or consequential damages (including any and all implied warranties, warranties of fitness for particular purpose, non-infringement and merchantability.) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Statements regarding the suitability of products for certain types of applications are based on UNSEMI knowledge of typical requirements that are often placed on UNSEMI products in generic applications. Such statements are not binding, statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify UNSEMI's terms and conditions of purchase, including but not limited to the warranty expressed therein. Unless otherwise agreed in writing, UNSEMI product is not designed, authorized or warranted to be suitable for use in medical life-saving, or life-sustaining application , nor in applications where failure or malfunction of a UNSEMI product can reasonably be expected to result in personal injury, death or severe property or environmental damage. UNSEMI and its suppliers accept no liability for inclusion or use of UNSEMI products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. All referenced brands, product names, service names and trademarks are the property of their respective owners.