312929 MACOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
AMP MATE-N-LOK* 2 Connectors 16DEC 98 RevA EO ood WIRE CONTACT PART NUMBERS EES RANGE 6) (Awe) strip | LOOSE | STRIP | LOOSE MAX. Al) VertcatPin 25-20 | 119-475 a ~ 201-920 one 20-16 ° ~ Be Gi N WN Plug Housing © SS \\ Locking Latch LE, AS g Ceres oN A N ss LE ; AE <Jf s j NG gs C4 1 Lak gb CK Sais Latching Kf ap \\ Neg ne ae Ear A) A Cap Housing LAG Ss wre 4 . Latching Arm Figure 1 1. INTRODUCTION 2. Rotate back side (wire end) of connector a | | housing 180° along the pivot track, until the first This instruction sheet provides assembly and tooth of each latching arm engages; this is the disassembly procedures for AMP* Mini—Universal open position. See Figure 2. MATE-N-LOK 2 Connectors. Connector components are listed in Figure 1. fey fe wire end of the housing must be in the open position before insertion of terminated contacts. All dimensions are in metric units [with U.S. NOTE hea ——— customary units in brackets}. Pivot Track i i i i First Tooth Reasons for reissue are provided in Section 8, . REVISION SUMMARY. Ge Latching Arm — : 2. DESCRIPTION 1 QO a a Wire End Mini-Universal MATE-N-LOK 2 plug and cap aN Sy Open connector assemblies may be used in free hanging or ' Pera s Position printed circuit (pc) board applications. Plug and cap | CL Wies —---' ~ connector assemblies are fully polarized for proper H Teed! alignment. Positive locking features prevent be accidental disengagement of connector assemblies. —-— aller tll Lot 3. ASSEMBLY PROCEDURES Latcing Arm [ ere IE] 1. Select appropriate pin and socket contacts from Engaged c= table in Figure 1. Follow termination procedures , shown in Application Specification 114-1111. Figure 2 SS AMP Incorporated, Harrisburg, PA 17105 TOOLING ASSISTANCE CENTER 1-800-722-1111. AMP FAXPRODUCT INFO 1-800-522-6752 1013 This AMP controlled document is subject to change. For latest revision call the AMP FAX number. ©Copyright 1998 by AMP Incorporated. All Rights Reserved. LOCB “Trademark Form 404-25 1/98
ANP Mini-Universal MATE-N-LOK 2 Connectors 408-3393 SS Open Positi Locking Latches and Tabs Pen ostion Must be Securely Fastened “ 9 Q LS aN S ZED < ZZ L SLA | ALK? & AED i db ry) | cE (al \\ <Z Selle S69 GAs \\ oh 6 6 Q \\ Key BE Nin Slee Ry rh d First Tooth of Latching Ears Latching Arm Figure 7 Figure 9 2. Grasp the selected wire by the insulation barrel 6. UNMATING CONNECTORS and pull using a twisting motion until terminated To unmate plug and cap connectors, depress locking contact is free from housing as shown in Figure 10. latch of the plug connector and pull straight away 3. Repeat Step 2 for additional contacts. from cap connector. As shown in Figure 8. . Terminated Contact . Depress Locking S nsulation barre Latch Here BESS (/ZILILLLL LF, r ne ee ee Pull => QS | (——— 00 oe SSS —— ye ra) aaa EE ee eye ao Lhe A bX VZZEZZZE ASS o iN IN| #! ZAG a —— Ee aX Figure 10 J y Fk 8. REVISION SUMMARY ‘igure 8 Since the previous release of this instruction sheet, the followi h: hi be de: 7. DISASSEMBLY PROCEDURES je vorowing enanges nave been mace Per EC 0990—-1209-98 ReMi 20 prevent damage to the connector assembly, a the wire end must be in the open position before * Added part numbers to table in Figure 1 the removal of contacts. * Changed “Latching Lance” to “Latching Arm” in zi 7 : all instances. 1. Deflect latching ears one at a time, then lightly . A pull wire end of the plug assembly away from ° Revised paragraph in section 33 housing until the first tooth of the latching arms * Revised paragraph in section 5.2 engage. See Figure 9. ¢ Added CAUTION to section 7 ¢ Revised paragraph in secti 7.2 CAUTION Take care not to over deflect the latching ears. evised paragraph in section Rn ee RevA 3013 Form 40440 1/98