408-6930 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Instruction SheetTerminating Head 58247- 1 For MTA- 156 Receptacle Connectors 408- -6930 LOC B 1 of 5E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1-- 800-- 722-- 1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.te.com
19 APR 11 Rev FUsing Discrete Wire
(Insertion Rod) Wire Inserter Feed Slide Tool Base With Lock (Ramp) Without Lock (Ramp) With Lock, With Polarizing Tabs Without Lock, With Polarizing Tabs Mass Termination Assembly (MTA)- -156 Insulation Displacement Contact (IDC) Closed- -End Receptacle Connectors 1. INTRODUCTION Terminating Head 58247- -1 (shown in Figure 1) is designed to terminate discrete wire in MTA- -156 IDC closed- -end receptacle connectors with or without lock (ramp) and with or without polarizing tabs. Slotted contacts for insulation displacement termination are pre- -assembled on 3.96- -mm [.156- -in.] centerlines in each color- -coded housing for a specific wire size. The head must be installed in Pistol Grip Manual Handle Assembly 58074- -1 or Pistol Grip Pneumatic Handle Assembly 58075- -1. For head installation and removal, refer to Instruction Sheet 408- -6790 for the manual handle assembly and 408- -6789 for the pneumatic handle assembly. For detailed connector description and application requirements, refer to Application Specification 114- -1020. Read these and all referenced instructions thoroughly before using the head. All numerical values in this instruction sheet are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Figures are not drawn to scale. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION The head serves as a guide and support for the connector during termination. Features of the head (shown in Figure 1) and their function are as follows. Wire Inserter— forces the wire into the two slotted beams of the contact. Note that it provides support for the contact beams when applying insertion force on the wire. Adjuster (Insertion Rod)— is a piston for the wire inserter and regulates wire inserter travel. Feed Slide— automatically positions the connector after each termination. Locating Pawl (or Anti- -Backup Pawl)— aligns the connector for insertion, and retains it during termination. 3. SETUP AND TEST INSPECTION The adjuster (insertion rod) is preset for wire sizes 26 through 18 AWG. If the wire is being inserted too deeply or not deeply enough inside the contact, it may be necessary to adjust the depth of the wire inserter or, in addition, if the pneumatic handle assembly is being used, it may be necessary to adjust the air pressure. Proceed as follows: 3.1. Setup 1. Determine the wire size, and select the appropriate color- -coded connector from Figure 2. WIRE SIZE (AWG) CONNECTOR COLOR CODE
26 Blue
24 Natural
22 Red
20 Yellow
18 Orange
i
3 — The contact beams are NOT deformed. If damage is apparent, replace the contacts in accordance with the instructions packaged with the connector. 4 — The wire insulation is NOT nicked or cut in any area other than the two contact slots. 5 — The wire extends past the wire retainer (strain relief) of the connector. 4. WIRE INSERTION DEPTH ADJUSTMENT(See Figure 4) 1. Remove the head from the handle assembly. 2. If the wire is inserted too deeply (more than the required wire insertion depth), reduce the wire insertion depth by turning the adjuster1/6 of a revolution clockwise. The wire insertion depth will be reduced by approximately 0.20 mm [.008 in.]. If the wire is bottomed in the contact slot, this indicates that the adjuster is set to the maximum wire insertion depth — DO NOT turn the adjuster counterclockwise; otherwise damage to the head may occur. If the wire is not inserted deeply enough (less than the required wire insertion depth), increase the wire insertion depth by turning the adjuster 1/6 of a revolution counterclockwise. The wire insertion depth will be increased by approximately 0.20 mm [.008 in.]. When turning the adjuster counterclockwise, make sure to check the wire insertion depth after EACH 1/6 revolution. If the adjuster is set past the maximum setting, damage to the head may occur. Figure 4 Turn CLOCKWISE to Reduce Wire Insertion Depth Turn COUNTERCLOCKWISE to Increase Wire Insertion Depth DO NOT Turn Past Maximum Setting Refer toCAUTION Adjuster Wire Insertion Depth Adjustment Note: 1/6 Revolution Equals 0.20 mm [.008 in.] Adjustment 5. TERMINATING PROCEDURE(Refer to Figure 5) There is no wire preparation required. 1. Insert the connector into the left side of the head. 2. Align the contact to be terminated with the wire inserter of the head (shown in Figure 1). Make sure that the locating pawl rests between the connector index ribs. 3. Insert an unstripped wire into the funnel area between the contact and the wire inserter until it bottoms on the tool base. 4. Squeeze the cam handle (manual) or depress the trigger (pneumatic) of the handle assembly, and hold it until the ratchet releases (manual) or the wire inserter bottoms (pneumatic). 5. Release the cam handle or trigger. The wire inserter will retract and the feed slide will automatically advance the connector to the next contact position. The locating pawl will move up and down as the connector is automatically advanced through the head. However, if movement is obstructed, or if desired, the locating pawl can be depressed and the connector moved manually out of the RIGHT side of the head. 6. Repeat Steps 2 through 5 until all contacts have been terminated. 7. Inspect each termination according to Paragraph 3.2. 6. MAINTENANCE AND INSPECTION 6.1. Daily Maintenance 1. Remove dust, moisture, and other contaminants with a clean, soft brush or lint- -free cloth. DO NOT use objects that could damage the head. 2. Make sure that all components are in place and properly secured. 3. Actuate the tool to make sure that the mechanisms inside the head function smoothly. 6.2. Periodic Maintenance 1. Remove any accumulated film with a suitable cleaning agent that will not affect plastic. 2. Make sure all components are in place and properly secured. 3. Check for chipped, cracked, worn, or broken areas on the head. If damage is evident, repair or replace the head. CAUTION CAUTION NOTE i NOTE i
Assembly (Manual Shown) Left Side of Head Feed Slide Tool Base Index Rib of Connector Locating Pawl Funnel Area 6.3. Inspection Regular inspections should be performed by quality control personnel with a record of quality control inspections remaining with the personnel responsible for the head. One inspection per month is the recommended frequency; however, operator training and skill, amount of use, working conditions, and established company standards are all factors to be considered in establishing inspection frequency. 7. REPLACEMENT AND REPAIR Customer- -replaceable parts are listed in Figure 6. A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by TE Connectivity to ensure quality and reliability. Order replacement parts through your representative, or call 1- -800- -526- -5142, or send a facsimile of your purchase order to 717- -986- -7605, or write to: CUSTOMER SERVICE (038- -035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105- -3608 For customer repair service, call 1- -800- -526- -5136. 8. REVISION SUMMARY Revisions to this instruction sheet include: S Updated document to corporate requirements S New logo
88.9 mm [3.50 in.] 25.4 mm [1.00 in.] 28.58 mm [1.125 in.] A A Weight: 8 5g[ 3o z ] Section A- -A 3 4 6 7 8 2 14 15 REPLACEMENT PARTS ITEM PART NUMBER DESCRIPTION QTY PER HEAD 1 312150- -1 HEAD, Finished 1 2 312138- -3 HOUSING, Insert 1 3 6- -22278- -5 SPRING, Compression 1 4 312147- -1 PAWL, Locating 1 5 4- -22430- -8 SCREW, Machine (4- -40¢.875 in. L) 4 6 21041- -7 PIN, Spiral Spring 1 7 312192- -1 PAWL, Feed 1 8 312154- -1 INSERTER, Wire 1 9 22488- -5 SPRING, Compression 1 10 312149- -1 ADJUSTER, Rod Insertion 1 11 312148- -1 ROD, Inserter 1 12 3- -21028- -2 PIN, Slotted Spring 1 13 312153- -1 CAM, Traverse Slide 1 14 1- -23147- -2 SPRING, Compression 1 15 312151- -1 SLIDE, Feed 1 Figure 6