408-4109 MACOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

©2011 Tyco Electronics Corporation, Berwyn, PA All Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names might be trademarks of their respective owners. Instruction Sheet TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 5 LOC B Pistol Grip Seating Tool Head 58569-1 for AMPMODU* MTE Connectors 408-4109

28 FEB 11 Rev C

  1. INTRODUCTION This instruction sheet covers the operation and maintenance of Pistol Grip Seating Tool Head 58569-1. See Figure 1. The seating tool is used to seat contacts into single-row AMPMODU MTE contact housing assemblies. The seating head tool will seat contacts in individual or strip form in a wire size range of 30 to 22. Read these instructions thoroughly before using the head. All dimensions on this document are in metric units [with U. S. customary units in brackets]. Figures are for reference only and are not drawn to scale. Reasons for revision of this document are given in Section 7, REVISION SUMMARY . 2. DESCRIPTION The seating tool is used in Manual Handle Assembly 58074-1, Bench-Mount Pneumatic Assembly 58338-1, or Electric Power Unit 931800-1. When installed into the appropriate power assembly, the seating tool will seat plastic housings over the previously terminated and inspected contacts of the single-row AMPMODU MTE contact housing assemblies. Refer to 408-6919 for a complete description of AMPMODU MTE connectors. For information concerning the setup and operation of the power assemblies, refer to instruction sheets 408-6790 and 408-9393, and to customer manual 409-5746. Note that the pneumatic assemblies are designed to operate between 280-480 kPa [40 through 70 psi]. Before contacts can be seated into the housing assemblies, all contact positions on the entire carrier strip must be cycled through an insertion station, even if a slot is intentionally left empty. Features of the head and their functions are as follows:
  • Adjuster (Insertion Rod) - is a piston for the slide bar and regulates its travel.
  • Drive Bar - is the reversible block that actually pushes against the contact housing.
  • Slide Bar - is the guiding bar that maintains the alignment of the drive bar, and guides it.
  • Guide Cover - goes between the wire and the carrier strip and provides backup support to the carrier strip during seating. 3. SETUP AND ADJUSTMENTS The seating depth adjustment on the insertion rod adjuster is preset prior to shipment. If, after inspection, it is determined that the contacts are not seated properly, re-adjust the seating depth. 3.1. For Pistol Grip Manual Handle Assembly and Electric Power Unit 1. Select a terminated connector. 2. Load connector into the seating tool and cycle the tool. 3. Inspect seated connector according to Figure 6. 4. If contacts are properly seated in the housings, remove connector from the seating tool and Drive Bar Slide Bar Guide Cover Insertion Rod Adapter NOTE i NOTE i ORIGINAL INSTRUCTIONS

CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 Tools and/or seating head tools may also be returned for evaluation and repair. For repair service, contact a Tyco Electronics Representative at 1-800-526-5136. 7. REVISION SUMMARY Since the previous release, the TE logo was applied. Figure 7 Weight: 1952 g [4 lb. 5 oz.] ITEM NO. TE PART NUMBER DESCRIPTION QTY PER ASSY 1 189079-1 FRAME 1 2 217844-1 BAR, Slide 1 3 1-21028-2 PIN, Slotted Spring [.0632 Dia X .880] 1 4 217845-1 LINK 1 5 21028-1 PIN, Slotted Spring [.062 X .190] 1 6 189085-1 ROD, Inserter 1 7 22488-5 SPRING, Compression 1 8 312149-1 ADJUSTER, Inserter Rod 1 9 217846-1 BAR, Drive 1 10 1-21000-3 SCREW, Socket Head Cap 4-40 X .250 1 11 217842-1 GUIDE 1 12 1-21003-5 SCREW, Flat-Head Cap 4-40 X .500 2 13 217843 COVER, Guide 1 14 1-21003-4 SCREW, Flat Head Cap 4-40 X .380 2 15 1-21003-7 SCREW, Flat Head Cap 4-40-40 X .750 2