DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 12
Technical content
Instruction SheetCrimping Die Assemblies for COPALUM* Terminals and Splices 408- -2353 LOC B 1 of 12E2010 Tyco Electronics Corporation, Berwyn, PA All Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other product names, logos, or company names might be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1- -800- -722- -1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.tycoelectronics.com
25 MAR 10 Rev Band HF- 30 Pin and Socket Contacts
CRIMPING DIES USED IN . . . CRIMPING HEAD 69082, 1752786- -1 CRIMPING HEAD 69099, 1752868- -1 68034 68035 68036 68037 68037- -1 68050 68043 68044 68045 68046 68047 68048 68049 Retaining Screw Setscrew in Ram Crimping Head (Ref) Tool Head Radii Stationary Die (Nest) Die Radii Moving Die (Indenter) Flats on Shank Figure 1 1. INTRODUCTION This instruction sheet covers the use of Crimping Die A s s e m b l i e sl i s t e di nF i g u r e1 ,w h i c ha r eu s e dt oc r i m p COPALUM Terminals and Splices and HF- -30 Pin and Socket Contacts. The die assemblies are used in Crimping Heads 69082, 69099, 1752786- -1, and 1752868- -1. Refer to instruction sheet packaged with the crimping head for information concerning die installation and general performance of the head. Read these instructions thoroughly before using the die assemblies. See Section 7, REVISION SUMMARY, for revision information. All dimensions on this document are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference only and are not drawn to scale. 2. DESCRIPTION The die assemblies consist of stationary dies (nest) and moving dies (indenter). Refer to Figure 2A (COPALUM contacts) or Figure 2B (HF- -30 Contacts) to ensure the compatibility of die assemblies, crimping heads, and terminals and splices. These dies are used to crimp COPALUM Terminals and Splices on No. 8 through 500 MCM stranded or solid, aluminum or copper{ wire and HF- -30 Pin and Socket Contacts for stranded aluminum and copper wire sizes specified in Figure 2B. Dies are coated with preservative to prevent rust and corrosion. Wipe this preservative away from dies, particularly from crimping areas. For further instructions on the hydraulic power unit and hydraulic crimping heads, refer to the instructions packaged with these tools. 2.1. Die Installation AVOID PERSONAL INJURY. Exercise extreme caution when using power unit. Avoid depressing foot switch or trigger control when installing or removing die assemblies. DO NOT MIX DIE COMPONENTS FROM DIFFERENT DIE SETS. The radii of both dies must match the radii of the tool. S e eF i g u r e1 . Crimping head No. 69099 is illustrated throughout this publication; however, die insertion, die removal and crimping instructions are the same for 69099, 69082, 1752786- -1, and 1752868- -1 crimping heads. Proceed as follows: 1. Loosen retaining screw in top section of crimping head. See Figure 1. {Butt Splices Only. Refer to Paragraph 3.3 NOTE i DANGER
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B2 of 12 Tyco Electronics Corporation 2. Insert shank of stationary die into top section of crimping head and tighten retaining screw. Ensure that the dies are inserted fully and that the “flats” on shanks are facing the operator. 3. Activate power unit to advance ram until setscrew is visible. AVOID PERSONAL INJURY. Exercise extreme caution when using power unit. Avoid depressing foot switch or trigger control when installing or removing die assemblies. 4. Loosen setscrew and insert shank of moving die into ram well. Tighten setscrew. 5. Activate power unit to complete cycle and allow ram to return to down position. 2.2. Die Removal 1. Loosen retaining screw in top section of crimping head and remove die. 2. Raise ram to full up position. Loosen setscrew in ram and remove die. AVOID PERSONAL INJURY. Exercise extreme caution when using power unit. Avoid depressing foot switch or trigger control when installing or removing die assemblies. 3. WIRE STRIPPING AND CRIMPING PROCEDURE 3.1. Wire Stripping Procedure 1. Select the proper size terminal, splice, or HF- -30 pin and socket contact for the wire size being used. See Figure 2A for COPALUM Terminal and Splices or Figure 2B for HF- -30 Pin and Socket Contacts. 2 .S t r i pw i r et od i m e n s i o ni n d i c a t e di nF i g u r e2 A for COPALUM Terminals and Splices or Figure 2B for HF- -30 Pin and Socket Contacts. Do NOT nick or cut conductor strands. When stripping wires for HF- -30 Pin and Socket Contacts, be sure to remove clear plastic insulation material from conductors prior to crimping. 3.2. Crimping COPALUM Terminals AVOID PERSONAL INJURY; when operating power unit, exercise caution while holding terminals or wire near crimping area. Never place anything within the crimping dies except COPALUM terminals and splices and HF- -30 pin and socket contacts. 1. Ensure that the wire size stamped on the terminal corresponds with the size marked on the dies. 2. Center terminal wire barrel in stationary die. Terminals may be crimped with tongue facing either die. (Tyco Electronics recommends the terminal positioning shown in Figure 3:) (tongue toward moving die.) Depending on conductor hardness, and if near maximum conductor CMAlimit is reached, some cracking may occur in crimp area when terminal is crimped with tongue toward stationary die. WIRE mm2 CMAD RANGE WIRE STRIP LENGTH CRIMPING CRIMPINGWIRE SIZE mm2 CMAD RANGE MIN MAX CRIMPING DIE ASSY CRIMPING HEAD 8 6.638 - - 10.540 13,100 - - 20,800 10 32 [ 4062] 11 90 [ 4687] 68043 690992 26.652 - - 42.412 52,600 - - 83,700 68046 69099 1752868--1 1/0 42.412 - - 60.55 83,700 - - 119,500 18 25 [ 7187] 19 84 [ 7812] 68047 1752868--1 3/0 76.26 - - 96.27 150,500 - - 190,000 68049 1752786--1 1752786--1 DCircular Mil Area Figure 2A (For Crimping COPALUM Terminals and Splices - - See Paragraphs 3.2, 3.3, and 3.4) NOTE i DANGER DANGER CAUTION DANGER NOTE i
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts 3 of 12Rev B Tyco Electronics Corporation Nest (Stationary Die) Indenter (Moving Die) Part Number, Revision Information Ensure Terminal Dash Number Identifier Stamped on Terminal Agrees with Crimp Die Assembly Part Number and Wire Size Prior to Crimping HF- -30 Pin Contact Assembly HF- -30 Socket Contact Assembly SWIRE SIZE (mm2) WIRE TYPE- - STAMPED WIRE AREA (mm2) NOMINAL WIRE CMA WIRE STRIP LENGTH (mm) SCRIMPING DIE ASSY STERMINAL DASH NO. IDENTIFIER SCRIMPING DIE EMBOSSMENT IDENTIFIER CRIMPING HEAD(mm2) TYPE-- (mm2) CMA MIN MAX ASSY. IDENTIFIER IDENTIFIER HEAD 185 Alum 185 365,102 23.4 26.6 -- -- --z -- 1 300 150 Copper 150 296,029 23.4 26.6 -- -- --z -- 1 300 240 Alum 240 473,646 25.9 29.1 -- -- --z -- 2 400 185 Copper 185 365,102 25.9 29.1 -- -- --z -- 2 400 69082 300 Alum 300 592,058 29.7 32.9 68037- -1zz -- 3 600 69082 1752786- -1 240 Copper 240 473,646 29.7 32.9 68037- -1zz -- 3 600 400 Alum 400 789,410 29.7 32.9 68037zz -- 4 500 300 Copper 300 592,058 29.7 32.9 68037zz -- 4 500 SEnsure terminal dash number, crimp die assembly part number including its associated embossment identifier, and wire size stamped on wire, all agree prior to crimping. z Contact Tyco Electronics Engineering for preliminary part number information.zzPending product qualification approval. Figure 2B (For Crimping HF- -30 Pin and Socket Contacts - - See Paragraph 3.5) Figure 3 (cont’d) Stationary Die Center Wire Barrel in Die Moving DieE n do fW i r eM u s tb eF l u s h with or Extend Beyond End of Wire Barrel Top of Terminal Tongue Faces Moving Die Detail A COPALUM Terminal View Port Faces Stationary Die End of Splice Flush with Side of Die End of Wire Butts Against Wire Stop Detail B COPALUM Butt Splice
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B4 of 12 Tyco Electronics Corporation Figure 3 (end) Ends of Wires Must be Flush with or Extend Beyond Ends of Splice Center Splice in Die Detail C COPALUM Parallel Splice Detail D HF- -30 Contact Stationary Die (Nest) Hydraulic Crimp Head End of Barrel Flush with Edge of Die Wire inserted fully into contact until insulation bottoms on edge of contact. No wire strands should be visible. Moving Die (Indenter) Socket Contact Assembly HF- -30 Same Criteria Applies to Pin Contact Pin Contact Assembly HF- -30 H o u s i n gS t o po n Bottom Detail E Stationary Die (Nest) Flat Planar Surface of Crimp Die Nest Middle Plane of Contact Pin Contact Assembly HF- -30 Contact Location: The middle plane of contact should be parallel to the planar surface of the crimp die nest. This will prevent twist in the crimp relative to the planar mating surface of the contact. This applies to both pin and socket contacts. HF- -30 Contact Location
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B6 of 12 Tyco Electronics Corporation Figure 4 (See Paragraph 3.5.2) HF- -30 Pin Contact Assembly HF- -30 Socket Contact Assembly Verify perforated insert is presentprior to crimpingcontact assembly. Crimp will not function properly without insert. CAUTION Crimping Die Assemblies for COPALUM* Terminals and Splices and HF- -30 Pin and Socket Contacts
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts 7 of 12Rev B Tyco Electronics Corporation 4. CRIMP INSPECTION for COPALUM Terminals and Splices (Figure 5A) and HF- 30 Pin and Socket Contacts (Figure 5B) Inspect crimped contacts by checking the features described in Figure 5A or 5B as applicable. Use only the terminals, splices, and contacts that meet the conditions shown in the “ACCEPT” column. “REJECT” terminals, splices, and contacts can be avoided through careful use of the tabular information in Figure 2A or 2B and the instructions Section 3, and by performing regular die maintenance as instructed in Section 5. Figure 5A (Crimp Inspection Criteria for COPALUM Terminals and Splices) ACCEPT REJECT Terminal Parallel Splice Butt Splice 1 Crimps centered. Crimp may be slightly off center BUT NOT OFF END OF WIRE BARREL.
2 CMA of wire being used matches wire range specified
for each terminal dash number. 3 Insulation does not enter wire barrel.
4 Wire is visible through inspection hole of butt splice,
and is flush with or extends slightly beyond end of terminal wire barrel.
5 On parallel splices, bare wire ends must be flush with
or extend slightly beyond end of barrel. 1 Crimped off end of splice or terminal.
2 CMA of wire being used does not match wire range
stamped on terminal, splice, or dies. 3 Insulation entered barrel of terminal or splice. CHECK FOR INCORRECT STRIP LENGTH. 4 Wire not inserted far enough in terminal or splice. End of wire must be visible through inspection hole of butt splices, and be flush with or extend slightly beyond end of terminal wire barrel or parallel splice.
5 Excessive “flash” indicates wrong wire, terminal,
splice, or die combination was used. 6 Nicked or missing strands. 4 5 Wire Range Stamped Here Wire Range Stamped Here Wire Range Stamped Here Wire Range Stamped Here COPALUM Terminals and Splices
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B8 of 12 Tyco Electronics Corporation Figure 5B (Crimp Inspection Criteria for HF- -30 Pin and Socket Contacts) ACCEPT 1 Crimps centered. Crimp may be slightly off center BUT NOT OFF END OF WIRE BARREL. 3 Insulation does not enter wire barrel. No nicked, missing, or broken wire strands.
6 Crimp die embossment, and wire size agree
with table in Figure 2. The verification of the correct terminal dash number used with proper crimp die and wire size must be done priorto crimping of contacts. See Paragraph 3.5.1. Crimp die embossment, and wire size agree with table in Figure 2. The verification of the correct terminal dash number used with proper crimp die and wire size must be done priorto crimping of contacts. See Paragraph 3.5.1. Top View Bottom View Top View Bottom View Cutout for Housing Latch Cutout for Housing Latch Housing StopCutout for Housing Latch Cutout for Housing Latch HF-30 Pin and Socket Contacts
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts 9 of 12Rev B Tyco Electronics Corporation 5. MAINTENANCE/INSPECTION AVOID PERSONAL INJURY; exercise extreme caution when using power unit. Avoid depressing foot switch or trigger control when installing or removing die assemblies. Customer- -replaceable parts are listed in Figure 9. A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Crimping Die Assemblies are inspected before shipment. Tyco Electronics recommends that the die assembly be inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment. 5.1. Daily Maintenance It is recommended that each operator of the tool be made aware of - - and responsible for - - the following three steps of daily maintenance: 1. Remove dust, moisture, and other contaminants with a clean brush, or a soft, lint- -free cloth. Do NOT use objects that could damage the dies. 2. Make certain the dies are protected with a THIN coat of any good SAE 20 motor oil. DO NOT OIL EXCESSIVELY. Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 3. When the dies are not in use, mate them and store the tool in a clean, dry area. 5.2. Periodic Inspection Tyco Electronics recommends that a maintenance and inspection program be performed periodically to ensure dependable and uniform terminations. Though recommendations call for at least one inspection a month, frequency of inspection depends on: 1. The care, amount of use, and handling of the dies. 2. The presence of abnormal amounts of dust and dirt. 3. The degree of operator skill. 4. Your own established standards. A. Visual Inspection 1. Remove all lubrication and accumulated film by immersing the die assembly in a suitable commercial degreaser that will not affect paint or plastic material. 2. Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage is evident, the dies must be replaced or repaired. Examples of possible damaged die closure surfaces are shown in Figure 6. If desired, you may return them to Tyco Electronics for evaluation and repair (see Section 6, REPAIR). Figure 6 Pitted Broken Corner B. Gaging the Crimping Chamber This inspection requires the use of a plug gage conforming to the diameters provided in Figure 7. Tyco Electronics does not manufacture or market these gages. The following procedure is recommended for inspecting the die closures. 1. Clean oil or dirt from the die closure areas, and plug gage elements. 2. Assemble and adjust dies to meet the “gage dimension” indicated in Figure 8, Detail A. 3. With dies positioned at the “gage dimension,” inspect the bar crimp closure using the proper plug gage. Align the GO element of the gage with the crimping chamber. Push the element straight into the chamber without using force. The GO element must pass completely through the crimping chamber without using force, as shown in Figure 8, Detail A. 4. Align the NO- -GO element with the crimping chamber and try to insert it straight into the chamber. The NO- -GO element may start entry, but must not pass through, as shown in Figure 8, Detail A. 5. With dies positioned at “gage dimension,” check the right and left rectangular crimp closures using the proper plug gage in the same manner as Steps 4 and 5; see Figure 8, Detail B. DANGER NOTE i
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B10 of 12 Tyco Electronics Corporation Suggested Plug Gage Design - Bar Crimp Suggested Plug Gage Design - Rectangular Crimp GO Dim. “B” Dia. NO- -GO Dim. NO- -GO Dim.GO Dim. “B” Dia. 50.8 [2.00] Min. Typ. Bar Crimp Closure Configuration Rectangular Crimp Closure Configuration “G” Dia. “G” Dia. 50.8 [2.00] Min. Typ. DIE SET GAGE ELEMENT DIMENSIONS (“B” DIA) DIE SET GAGE ELEMENT DIMENSIONS (“G” DIA) SET GO NO- -GO SET GO NO- -GO 68034 5.512- -5.519 [.2170- -.2173] 5.763- -5.766 [.4970- -.4973] 12.977- -12.979 [.5109- -.5110] 68035 6.172- -6.180 [.2430- -.2433] 6.424- -6.426 [.5490- -.5493] 14.298- -14300 [.5629- -.5630] 68036 6.960- -6.967 [.2740- -.2743] 7.211- -7.214 [.6140- -.6143] 15.949- -15.951 [.6279- -.6280] 68037 7.874- -7.882 [.3100- -.3103] 8.125- -8.128 [.6900- -.6903] 17.879- -17.882 [.7039- -.7040] [.2850- -.2853] 7.490- -7.493 [.6430- -.6433] 16.685- -16.688 [.6569- -.6570] 68043 1.702- -1.709 [.0670- -.0673] 1.953- -1.956 [.1650- -.1653] 4.544- -4.547 [.1789- -.1790] 68044 2.007- -2.014 [.0790- -.0793] 2.258- -2.260 [.2070- -.2073] 5.611- -5.613 [.2209- -.2210] 68045 2.464- -2.471 [.0970- -.0973] 2.715- -2.718 [.2250- -.2253] 6.068- -6.071 [.2389- -.2390] 68046 2.718- -2.725 [.1070- -.1073] 2.969- -2.972 [.2610- -.2613] 6.982- -6.985 [.2749- -.2750] 68047 3.404- -3.411 [.1340- -.1343] 3.655- -3.658 [.3120- -.3123] 8.278- -8.280 [.3259- -.3260] 68048 3.835- -3.843 [.1510- -.1513] 4.087- -4.089 [.3490- -.3493] 9.218- -9.220 [.3629- -.3630] 68049 4.343- -4.351 [.1710- -.1713] 4.595- -4.597 [.3890- -.3893] 10.233- -10.236 [.4029- -.4030] 68050 4.8511- -4.859 [.1910- -.1913] 5.103- -5.105 [.4410- -.4413] 11.554- -11.557 [.4549- -.4550] Figure 7 If both the bar crimp and the rectangular crimp closures meet the plug gage conditions, the closures may be considered dimensionally correct and should be lubricated with a thin coat of any good SAE 20 motor oil. If the dies do NOT conform, the dies must be replaced or repaired before returning them to service. See Section 6, REPAIR. For additional information concerning the use of the plug gage, refer to Instruction Sheet 408- -7424.
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts 11 of 12Rev B Tyco Electronics Corporation Figure 8 Inspection of Bar Crimp Closure Inspection of Rectangular Crimp Closure Detail A Detail B Right Die Closure Left Die Closure Radius of Bar Crimp Gage Dimension: 42.27 [1.664] for 8- -3/0 Sizes 74.3 [2.925] for 4/0- -500 MCM Sizes “GO” Gage Must Pass Completely Through the Die Closure “NO- -GO” Gage May Enter Partially, but Must Not Pass Completely Through the Die Closure “GO” Gage Must Enter to Radius of Bar Crimp “NO- -GO” Gage May Enter Partially, but Must Not Enter to Radius of Bar Crimp 6. REPAIR/REPLACEMENT Replaceable parts are listed in Figure 9. Parts other than those listed in Figure 9 should be replaced by Tyco Electronics to ensure quality and reliability of the tool. Order replacement parts through your Tyco Electronics Representative, or call 1- -800- -526- -5142, or send a facsimile of your purchase order to 1- -717- -986- -7605, or write to: CUSTOMER SERVICE (38- -35) TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105- -3608 For tool repair service, please contact an Tyco Electronics Representative at 1- -800- -526- -5136. 7. REVISION SUMMARY S Updated document to corporate requirements S Added new part number 68037- -1 to tables in Figures 1, 2, 7, and 9 S Added, deleted, or changed text in Section 2, 3.3, and 3.4 S Deleted old and added new artwork to Figure 2 S Added new Paragraph 3.5.1 and renumbered S Added new Figure 4 and renumbered S Added new callouts to Figures 1, 2B, 3, and deleted callout and added text to Figure 5B S Combined Figures 6 and 7 and renumbered
408- 2353Die Assemblies for COPALUM Terminals and Splices and HF- 30 Pin and Socket Contacts Rev B12 of 12 Tyco Electronics Corporation ASSEMBLY ITEM 1 MOVING DIE (INDENTER) ITEM 2 STATIONARY DIE (NEST) 68034 1- -307586- -3 1- -307585- -3 68035 1- -307586- -4 1- -307585- -4 68036 1- -307586- -5 1- -307585- -5 68037 1- -307586- -6 1- -307585- -6 68043 307586- -1 307585- -1 68044 307586- -2 307585- -2 68045 307586- -3 307585- -3 68046 307586- -4 307585- -4 68047 307586- -5 307585- -5 68048 307586- -6 307585- -6 68049 307586- -7 307585- -7 68050 307586- -8 307585- -8 Figure 9