2R075-4S SUNMATE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

0.5 ± 0.1 4.0 ± 0.2 4.2 ± 0.2 3.5 5.0 1.3 Size:4.2mm*4.0mm DC Spark-over voltage: 75~2000V Stable breakdown voltage. High insulation resistance. Low capacitance (<1pF) High holdover voltage. Large absorbing transient current capability. Low Capacitance Micro-Gap Design Cable Modem xDSL Set-Top Box Satellite and CATV equipment Power supplier Consumer electronics General telecom equipment

Applications

Electriacl Characteristics Part Number DC Spark-over Voltage Maximum Impulse Breakdown Voltage Max. Impulse Discharge Current (8/20μs) Impulse Life (10/1000μs) Normal Alternating Discharge Current DC Holdover Voltage Minimum Insulation Resistance Maximum Capacitance (1MHz) 100V/S 100V/ μs 1KV/ μs times times 300 A 50Hz 1Sec Single

9 Cycles <150ms

(V) (V) (V) (KA) Times (A) (V) (GΩ) (pF) 2R075-4S 75±20% 700 800 5 3 300 3 6 52 1 0.5 2R090-4S 90±20% 700 800 5 3 300 3 6 52 1 0.5 2R150-4S 150±20% 600 800 5 3 300 3 6 80 1 0.5 2R230-4S 230±20% 600 700 5 3 300 3 6 150 1 0.5 2R250-4S 250±20% 600 700 5 3 300 3 6 150 1 0.5 2R300-4S 300±20% 600 700 5 3 300 3 6 150 1 0.5 2R350-4S 350±20% 650 800 5 3 300 3 6 150 1 0.5 2R400-4S 400±20% 700 800 5 3 300 3 6 150 1 0.5 2R470-4S 470±20% 800 900 5 3 300 3 6 150 1 0.5 2R600-4S 600±20% 900 1000 5 3 300 3 6 150 1 0.5 2R800-4S 800±20% 1300 1400 3 2 100 2 4 150 1 0.5 2R1000-4S 1000±20% 1500 1600 3 2 100 2 4 150 1 0.5 2R1200-4S 1200±20% 1700 1800 3 2 100 2 4 150 1 0.5 2R1400-4S 1400±20% 1700 1800 3 2 100 2 4 150 1 0.5 2R1500-4S 1500±20% 2000 2100 3 2 100 2 4 150 1 0.5 2R1600-4S 1600±20% 2000 2100 3 2 100 2 4 150 1 0.5 2R1800-4S 1800±20% 2500 2600 3 2 100 2 4 150 1 0.5 2R2000-4S 2000±20% 2700 2600 3 2 100 2 4 150 1 0.5 DC Spark-over Voltage DC Measuring Voltage 75-90V 50V 150-400V 100V 470-800V 250V 1000-2000V 500V

Pb – Free assembly Pre Heat - Temperature Min (T s(min) )1 50°C - Temperature Max (T s(max) )2 00°C - Time (Min to Max) (t s )6 0 – 180 secs Average ramp up rate (Liquidus Temp L ) to peak 3°C/second max T S(max) to T L - Ramp-up Rate 5°C/second max - Temperature (T L ) (Liquidus) 217°C - Temperature (t L )6 0 – 150 seconds Peak Temperature (T P )2 60 +0/-5 Time within 5°C of actual peak Temperature (t p ) 10 – 30 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P )8 minutes Max. Do not exceed 260°C Time erutarep meT T P T L T S(max) T S(min) t P t L t S time to peak temperature (t 25ºC to peak) Ramp-down Ramp-up Preheat Critical Zone T L to T P Dwell Time 100 120 140 160 180 200 220 240 260 280 300 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 Time (Seconds) Temperature (°C) - Measured on bottom side of board Cooling TimePreheat Time Wave ParameterL ead-Free Recommendation Preheat: (Depends on Flux Activation Temperature) (Typical Industry Recommendation) Temperature Minimum: 100 C Temperature Maximum: 150 C Preheat Time: 60-180 seconds Solder Pot Temperature: 280 C Maximum Solder Dwell Time: 2-5 seconds Soldering parameters -wave soldering Recommended process parameters