2R075B-8S SUNMATE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

Size:8.3mm*6.0mm DC Spark-over voltage: 75~800V Stable breakdown voltage. High insulation resistance. Low capacitance (<1pF) High holdover voltage. Large absorbing transient current capability. Low Capacitance Micro-Gap Design Cable Modem xDSL Set-Top Box Satellite and CATV equipment Power supplier Consumer electronics General telecom equipment /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068 /C0068

Applications

DC Spark-over Voltage DC Measuring Voltage 70-90V 50V 150-400V 100V 470-1000V 250V Part Number DC Spark-over Voltage Maximum Impulse Breakdown Voltage Max. Impulse Discharge Current (8/20μs) Impulse Life (10/1000μs) Normal Alternating Discharge Current DC Holdover Voltage Minimum Insulation Resistance Maximum Capacitance (1MHz) 100V/S 100V/ μs 1KV/ μs times times 100 A 50Hz 1Sec Single

9 Cycles <150ms

(V) (V) (V) (KA) Times (A) (V) (GΩ) (pF) 2R075B-8S 75±20% 600 700 15 10 500 10 15 52 1 0.8 2R090B-8S 90±20% 600 700 15 10 500 10 15 52 1 0.8 2R150B-8S 150±20% 500 700 15 10 500 10 15 52 1 0.8 2R230B-8S 230±20% 500 600 15 10 500 10 15 80 1 0.8 2R250B-8S 250±20% 500 600 15 10 500 10 15 150 1 0.8 2R300B-8S 300±20% 550 650 15 10 500 10 15 150 1 0.8 2R350B-8S 350±20% 600 700 15 10 500 10 15 150 1 0.8 2R400B-8S 400±20% 650 750 15 10 500 10 15 150 1 0.8 2R470B-8S 470±20% 750 850 15 10 500 10 15 150 1 0.8 2R600B-8S 600±20% 900 1000 15 10 500 10 15 150 1 0.8 2R800B-8S 800±20% 1000 1100 15 10 500 10 15 150 1 0.8 2R1000B-8S 1000±20% 1500 1600 15 10 500 10 15 150 1 0.8

Pb – Free assembly Pre Heat - Temperature Min (T s(min) )1 50°C - Temperature Max (T s(max) )2 00°C - Time (Min to Max) (t s )6 0 – 180 secs Average ramp up rate (Liquidus Temp L ) to peak 3°C/second max T S(max) to T L - Ramp-up Rate 5°C/second max - Temperature (T L ) (Liquidus) 217°C - Temperature (t L )6 0 – 150 seconds Peak Temperature (T P )2 60 +0/-5 Time within 5°C of actual peak Temperature (t p ) 10 – 30 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P )8 minutes Max. Do not exceed 260°C Time erutarep meT T P T L T S(max) T S(min) t P t L t S time to peak temperature (t 25ºC to peak) Ramp-dow Ramp-up Preheat Critical Zone T L to Dwell Time 100 120 140 160 180 200 220 240 260 280 300 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 Time (Seconds) Temperature (°C) - Measured on bottom side of board Cooling TimePreheat Time Wave ParameterL ead-Free Recommendatio Preheat: (Depends on Flux Activation Temperature) (Typical Industry Recommendation) Temperature Minimum: 100 C Temperature Maximum: 150 C Preheat Time: 60-180 seconds Solder Pot Temperature: 280 C Maximum Solder Dwell Time: 2-5 seconds Soldering parameters -wave soldering Recommended process parameters