2AS1 MULTICOMP | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
www.element14.com www.farnell.com www.newark.com Page <1> V1.016/02/18 2A Series Sealed Sub-Miniature Toggle Switches Specifications Mechanical Life : 30,000 make-and-break cycles. Contact Resistance : 20mΩ max. initial @ 2-4V DC 100mA for both silver and gold plated contacts Insulation Resistance : 1,000MΩ min. Dielectric Strength : 1,000 Vrms min. @ sea level Operating Temperature : -40°C to 85°C Materials Case and Bushing : Glass filled nylon 6/6, flame retardant, heat stabilized (UL94V-0) Actuator : Brass, Chrome plated, internal O-ring seal. Standard for all actuators Switch Support : Brass, Tin plated Contact / Terminals : Copper alloy with Silver or Gold plated Switch Function Contact Material Options Contact Plating Terminal Plating Ratings Q Silver Q = Gold flash over silver 3 Amps with resistant load @ 120V AC or 28V DC
1 Amps with resistant load @ 250V ACC Gold over Silver C = Gold over silver
R Gold R = Gold 0.4 Volt - Amps (VA) max. @ 20V max. (AC or DC) No. Poles UL/CSA Model No. Model No. Switch Function Connected Terminals / Schematic SP Q22A11 2AS1 ON NONE ON 2-3 N/A 2-1 Q22A12 2AS2 ON NONE MOM Q22A13 2AS3 ON OFF ON OPENQ22A14 2AS4 MOM OFF MOM Q22A15 2AS5 ON OFF MOM Q22A16 2AS6 OFF NONE ON OPEN N/A 3-1 DP Q22A21 2AD1 ON NONE ON 2-3, 5-6 N/A 2-1, 5-4 Q22A22 2AD2 ON NONE MOM Q22A23 2AD3 ON OFF ON OPEN MOM = Momentary
www.element14.com www.farnell.com www.newark.com Page <2> V1.016/02/18 2A Series Sealed Sub-Miniature Toggle Switches Pole Options SPDT DPDT P.C. Mounting P.C. Mounting 2AS6 Models : Omit 2nd terminal Dimensions : Inches (Millimetres) Actuator Options Bushing Options Actuator shown with A1 Bushing, sub 0.02" (0.5mm) for A3 Bushing. Plastic Actuator A1, A3 for SPDT / A2 for DPDT
www.element14.com www.farnell.com www.newark.com Page <3> V1.016/02/18 2A Series Sealed Sub-Miniature Toggle Switches P.C. Mounting P.C. Mounting P.C. Mounting Dimensions : Inches (Millimetres) Termination Options Other Termination Options M6 Right angle P.C. Mount M6N Right angle P.C. Mount Snap-in bracket M7 Vertical right angle P.C. Mount M7N Vertical right angle P.C. Mount Snap-in bracket VS2 Vertical bracket P.C. Mount SPDT SPDT DPDT
www.element14.com www.farnell.com www.newark.com Page <4> V1.016/02/18 2A Series Sealed Sub-Miniature Toggle Switches VS2 VS2 DPDT SPDT DPDT P.C. Mounting P.C. Mounting P.C. Mounting Snap-in Termination Options Dimensions : Inches (Millimetres)
www.element14.com www.farnell.com www.newark.com Page <5> V1.016/02/18 2A Series Sealed Sub-Miniature Toggle Switches Important Notice : This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell Limited 2016. Part Number Explanation Soldering Processes Manual Soldering : Use soldering iron of 30 watts, controlled at 350°C approximately 5 seconds while applying solder. Wave Soldering : Recommended Soldering Temperature: 270 ± 5°C Duration of Solder Immersion: Max 5 sec. (PCB is 1.6mm in thickness)