24WR10KLFTR BITECH | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Seal 85°C Fluorinert® Temperature Coefficient, Maximum ±100ppm/°C (<200 ohms = ±250ppm/°C) Operating Temperature Range –55°C to +125°C Thermal Shock 5 cycles, –55°C to +125°C (2% ∆RT, 2% ∆VR) Moisture Resistance Ten 24 hour cycles (3% ∆RT) Shock, 6ms Sawtooth 100G’s (2% ∆RT, 1% ∆VR) Vibration 20G’s, 10 to 2,000 Hz (1% ∆RT, 1% ∆VR) High Temperature Exposure 250 hours at 125°C (2% ∆RT, 1% ∆VR) Rotational Life 200 cycles (5% ∆RT) Load Life at 0.5 Watts 1,000 hours at 70°C (3% ∆RT) Resistance to Solder Heat 350°C for 3 sec. (1% ∆RT) MECHANICAL Mechanical Stops Solid Stop Strength, Minimum 3 oz.-in. (200 gr-cm) Torque, Maximum 2 oz.-in. (150 gr-cm) Weight, Nominal .01 oz.(0.3 grams) MODEL 24 4mm Diameter Single Turn Cermet Trimming Potentiometer Fluorinert® is a registered trademark of 3M Company. Specifications subject to change without notice. Standard Resistance Range, Ohms 10 to 1Meg Standard Resistance Tolerance ±20% (±10% available) Input Voltage, Maximum 200 Vdc or rms not to exceed power rating Power Rating, Watts 0.5 at 70°C derating to 0 at 125°C End Resistance, Maximum 1% or 3 Ohms, whichever is greater Actual Electrical Travel, Nominal 190° Dielectric Strength 500Vrms Insulation Resistance, Minimum 1,000 Megohms Resolution Essentially infinite Contact Resistance Variation, Maximum 2% or 3 Ohms, whichever is greater
.19 ± .01 4.8 ± 0.3 58.5° Typical
4 Places
Dia.08 ± .01 2.0 ± 0.3 .35 ± .04 9.0 ± 1.0 Dia .11 2.7 Dia. x .19 4.7 Max. Adjustment Slot .014
0.35 Deep
.02 0.5 Wide x .03
0.8 Deep
Note: Model 24W dimensions applicable to all other models except as noted. .39 ± .04 10 ± 1.0 .10 ± .01 2.5 ± 0.3 .14 ± .01 3.5 ± 0.3 .04 ± .01 0.5 ± 0.10 Solderable Terminal Leads Typical 3 Places Dia. .07 ± .01 1.8 ± 0.2 (1) (2) (3) OUTLINE DIMENSIONS (Inch/mm) Model 24W Top Adjust Model 24U Top Adjust .39 ± .04 10 ± 1.0 .19 4.7 Max. .20 ± .01 5.0 ± 0.3 .31 ± .04 8.0 ± 1.0 (1) (2) (3) .35 ± .04 9.0 ± 1.0 .008 0.20 Max. Dia. (1) (2) (3) .24 ± .01 6.0 ± 0.3 .16 ± .01 4.1 ± 0.3 .19 ± .01 4.8 ± 0.3 .26 ± .01 6.5 ± 0.3 .20 ± .04 5.0 ± 1.0 .14 ± .01 3.5 ± 0.3 .10 ± .01 2.5 ± 0.3 .03 ± .01 0.8 ± 0.3.07 ± .01 1.8 ± 0.2 Model 24S Side Adjust
(1) (2) (3) CW NOTES mm INCH English equivalents are based on 1 inch = 25.4mm and are provided for general information only. Tolerances unless otherwise specified: Linear = ± 0.3 mm (.01 in.)
ORDERING INFORMATION
24 W R 10K LF TR
TR = Tape & Reel RoHS Compliant Product Code - Optional Resistance Value Standard: PACKAGING Standard: Boxes Capacity = 100 Units Option: Tape & Reel (24U only) All units oriented with #3 pin toward direction of feed. Seat Plane to Centerline of Sprocket Hole = .71” (18 mm) Tape Width = 18 mm Sprocket = Single Hole .50” spacing Capacity = 1,000 Units Reel Diameter = 14” (363 mm) 100 1K 10K 100K 1Meg 200 2K 20K 200K 2Meg 500 5K 50K 500K STANDARD RESISTANCE VALUES, OHMS