114-18021 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
Verarbeitungs-Spezifikation Application Specification 114-18021
01 Dec 2016 Rev U
EC: - MQS (Micro Quadlok System) TE connectivity *Trademark | Indicates change This specification is a controlled document. Copyright 2000 by TE connectivity. All rights reserved 1 of 10 ECOC EGA0 LOC: AI Inhaltsverzeichnis Table of Contents Page / Seite 1. ZWECK 1. SCOPE 2 2. ZUSÄTZLICHE UNTERLAGEN 2. REFERENCED DOCUMENTS 2 2.1 Kundenzeichnungen 2.1 Customer Drawings 2 2.2 Produktspezifikation 2.2 Product Specificatio n 2 2.3 Verarbeitungsspezifikationen 2.3 Application S pecifications 2 2.4 Informationsblätter 2.4 Information Sheets 2 3. BESCHREIBUNG 3. DESCRIPTION 3 4. ANFORDERUNGEN 4. REQUIREMENTS 4 4.1 Leitung 4.1 Wire 4 4.2 Trennsteg und Grat 4.2 Cut off and Burrs 4 4.3 Drahtcrimp 4.3 Wire Crimp 4/ 5 4.4 Isolationscrimp 4.4 Insulation Crimp 5 4.5 Kontaktbereich 4.5 Contact Area 5 4.6 Form- und Lagetoleranzen 4.6 Shape and Positio nal 6 des gecrimpten Kontaktes Tolerances of the Crimp ed (siehe Bild 2) Contact (see Fig. 2) 5. CRIMPDATEN FÜR MQS 5. CRIMPING DATA FOR MQS 7 (MICRO QUADLOK SYSTEM) (MICRO QUADLOK SYSTEM) 6. CRIMPDATEN FÜR MQS 2-Punkt 6. CRIMPING DATA FOR MQS 2-Point 9 (MICRO QUADLOK SYSTEM 2-PUNKT) MICRO QUADLOK SYSTEM 2-Point
- ZWECK 1. SCOPE Diese Spezifikation beinhaltet die Richtlinien zur Verarbeitung von Stift- und Buchsenkontakten des MQS (Micro Quadlok System). Die Angaben gelten primär für halb- oder vollautomatische Verarbeitung, können jedoch auch nach Vereinbarung für Handcrimpwerkzeuge angewendet werden. Die Kontakte sind nach ihrer Verwendung, nach Drahtgrößenbereichen und Crimpdaten unter Pu nkt 5 und 6 aufgeführt. Hinweis: Für die Verarbeitung dürfen ausschließlich die unter Punkt 5 und 6 festgelegten TE- Werkzeuge verwendet werden. Ausnahmen regeln kundenspezifische Unterlagen. This specification contains the guidelines for the application of pin and socket contacts of the MQS (Micro Quadlok system). It applies primarily to the fully or semi-automatic application of the contacts; if agreed, it can also be applied to manual crimp tool. The contacts are listed by their use, the wire size ranges and the crimping data in section 5 and 6. Note: Only the TE crimp tool specified in section 5 and 6 may be used for application of the contacts. Any exceptions to this rule are defined by customer-specific documents. 2. ZUSÄTZLICHE UNTERLAGEN 2. REFERENCED DOCUMENTS 2.1 Kundenzeichnungen 2.1 Customer Drawings Maße und Werkstoffe der Kontakte sind den TE- Kundenzeichnungen zu entnehmen. The dimensions and materials of the contacts are shown in the TE customer drawings. 2.2 Produktspezifikation 2.2 Product Specification In der Produktspezifikation 108-18030 sind die Eigenschaften des MQS Kontaktsystems beschrieben. In der Produktspezifikation 108-18874 sind die Eigenschaften der MQS 2-Punkt Kontakte beschrieben. The product specification 108-18030 describes the characteristics of the MQS contact system. The product specification 108-18874 describes the characteristics of MQS 2-Point contacts. 2.3 Verarbeitungsspezifikationen 2.3 Application S pecifications Für die Crimpqualität gelten zusätzlich die allgemeinen Richtlinien der Verarbeitungsspezifikation 114-18022, die, sofern nicht vorhanden, gesondert anzufordern sind. Für die Verarbeitung von MQS-Kontakten mit Einzeldichtung gilt die Verarbeitungsspezifikation 114-18025. Crimpdaten für die Verarbeitung von Sonderleistungen siehe Spezifikation 114-18021-4 Maße für Crimper und Amboss siehe Spezifikation 114-18021-10 (restricted) The crimp quality must also comply with the general guidelines laid down in the application specification 114-18022. If this is not available, it must be ordered separately. Application specification 114-18025 applies to the application of MQS contacts with single-wire seals. Please see application specification 114-18021-4 for the crimp data for the application of special purpose cable. Crimper and anvil dimensions: see specification 114-18021-10 (restricted). 2.4 Informationsblätter 2.4 Information Sheets IS 7424 erklärt die Messung der Crimphöhe. IS 7424 explains how to measure the crimp height.
- BESCHREIBUNG 3. DESCRIPTION Die aufgeführten Bezeichnungen werden in der Spezifikation verwendet. The following terms are used in this specification. Bild 1 / Fig. 1 Auslauf am Crimp / Bellmouth Rastfeder / Locking Lance Überfeder und Kontaktkörper / Contilever spring and Contact body Drahtcrimp / Wire Crimp Leitung / Wire Isolationscrimp / Insulation Crimp Vorne / front Hinten / back Crimphöhe für Drahtcrimp / Crimp heigth for wire crimp Crimphöhe für Isolationscrimp / Crimp height for Insulation Crimp Trennsteg und Grat / Cut-Off and Burr Überstand Leiterende / Wire Extension Isolationsende / End of Insulation Leiterende / End of Wire
- ANFORDERUNGEN 4. REQUIREMENTS 4.1 Leitung 4.1 Wire A Auswahl A Selection Es dürfen nur Leitungen nach DIN 72551-FLR Teil 5 und 6, sowie FLR und FLU Leitungen nach LV112-1 verarbeitet werden, die die Bedingungen nach Tabelle 1 & 2 dieser Spezifikation erfüllen. Andere Leitungen benötigen die Freigabe der Entwicklungs- abteilung. Es sind nur Einzelanschläge zugelassen. Für Leiterquerschnitte kleiner 0,22mm² in zugverstärkter Ausführung gilt zusätzlich LV 112-4. Only wires in accordance with DIN 72551-FLR Parts 5 and 6 as well as FLR and FLU wires in accordance with LV112-1 which comply with the conditions specified in Table 1 & 2 of this specification may be used. Other wires require approval from the development department. Only single termination is permitted. For wire size smaller than 0,22mm² (reinforced version) additionally LV 112-4 is valid. B Vorbereitung Die Leitung wird nach den Längenangaben in der Tabelle 1 abisoliert. Einzeldrähte dür fen dabei weder beschädigt noch aufgespleißt oder abgeschnitten werden. B Preparation The wire must be stripped to the length specified in Table 1, taking care that the individual strands are neither bent nor cut off. 4.2 Trennsteg und Grat 4.2 Cut off and Burrs Der Trennsteg muss nach dem Crimpvorgang noch sichtbar sein. Maximale Länge 0,3mm. Der Grat an der Schnittstelle darf maximal 0,03mm betragen. The cut off must be visible after crimping. Its length may not exceed 0,3mm. The burr at the cut off point may not exceed 0,03mm. 4.3 Drahtcrimp 4.3 Wire Crimp A Lage des Leiters A Wire position Das Leiterende muss nach dem Crimpen 0,1 bis 0,7mm an der Vorderkante des Drahtcrimps vorstehen. Die Steck- und Rastfunktion des Kontaktes darf durch überstehende Einzeldrähte nicht beeinträchtigt werden. Bei Kontakten zum Einsatz in Steckverbindern mit Sammeldichtung oder bei Drahtgrößenbereich 0,75mm² darf der Leiterüberstand max. 0,4mm betragen. Hoch- stehende Einzeldrähte sind nicht zulässig. Das Isolationsende darf keinesfalls im Drahtcrimp eingecrimpt werden. After crimping, the end of the wire must extend 0,1 to 0,7mm beyond the front edge of the wire crimp. The mating and locking function of the contact must not be affected by the wire extension of single strands. At contacts used in connectors with family-seal or with a wire size range of 0,75mm², a wire extension of max. 0,4mm is allowed. Upraising single strands are not permitted. In no case may the end of the insulation be crimped under the wire crimp. B Crimpdaten B Crimping data Die Crimpform, Crimphöhen und –breiten sowie Leiterquerschnitte sind in der Tabelle 1 aufgeführt. Hinweis: Crimphöhenmessung nach Bedienungs- anleitung IS 7424 mit Bügelmessschraube (Crimp- höhenmikrometer), TE-Bestell-Nr. 675836-0. Die Crimpbreite ist ein werkzeuggebundenes Maß und als Abstand der Tangentenpunkte beider Einroll- radien zu den Flanken definiert. Die Prüfung der Crimpbreite als Fertigungskontrolle ist nicht möglich. Das Prüfmaß CP 1 bzw. CP 2 dient nur der Kontrolle der Crimpernennbreite im Werkzeug und nicht zur statistischen Überwachung der Crimpbreite bzw. der Qualität des Crimps. The shape, height and width of the crimp, and the wire range, are shown in Table 1. Note: measure the crimp height in accordance with operating instructions IS 7424 with a crimp height micrometer, TE Order No. 675836- 0. The crimp width is a tool-related dimension and is defined as the distance between the two tangential points of the rolling radii and the edges of the crimp. It is not possible to meassure the crimp width for production monitoring purposes. The inspection dimension CP 1 and CP 2 are used only for checking the nominal crimper width in the tool, not for statistical monitoring of the crimp width or the quality of the crimp.
Für DGB < 0,35mm² gilt folgende Ausnahme- regelung für die Schliffbildbeurteilung: For wire-size <0,35mm² the following except- ions for the Evaluation of Microsection are valid: - Flankenendenabstand R: Bei Leitungen mit 7 Einzeldrähten (zugverstärkte Leitungen) ist durch Auflaufen der Crimpflanken auf den Einzeldraht ein Umknicken der Flankenspitzen möglich. In diesem Bereich ist ein Anstoßen des Crimp- flankenendes an der Innenwand der Crimphülse zulässig (R=0). - Flank End Distance R: At wires with 7 strands (reinforced wire) due to stubbing of the crimp wing on a strand a bent in of the crimp wing ends may occur. In this area the crimp wing end may hit the inner wall of the crimp barrel (R=0) C Ausziehwerte C Extraction forces Die Ausziehwerte müssen die Anforderungen nach DIN EN 60352-2 erfüllen. The crimp extraction forces must comply with the requirements of DIN EN 60352-2. D Auslauf am Crimp D Crimp bellmouth Der hintere Auslauf beträgt entgegen den all- gemeinen Richtlinien für alle Drahtgrößenbereiche einheitlich 0,25±0,15mm. Ausnahme: Bei den 0.35mm²-Varianten ist ein Maß von 0,4±0,15mm zulässig. Ein Fehlen des vorderen Auslaufs ist erlaubt. Contrary to the general guidelines, the size of the rear bellmouth is 0,25±0,15mm for all wire ranges. Exception: At the 0.35mm² variants a bellmouth of 0,4±0,15mm is allowed. A missing of the front bellmouth is permitted. E Grat am Crimpboden E Burr on base of crimp Für den Grat am Crimpboden gelten die Forderungen gemäß Spec. 114-18022. According to Spec. 114-18022 4.4 Isolationscrimp 4.4 Insulation Crimp A Lage des Isolationscrimps A Position of the insu lation crimp Das Ende der Leiterisolation muss im Übergang zwischen Draht- und Isolationscrimp sichtbar sein. Das Isolationsende darf keinesfalls im Drahtcrimp eingecrimpt sein und darf umgekehrt maximal mit der Vorderkante des Isolationscrimps abschließen. The end of the insulation must be visible in the transition between the wire crimp and the insulation crimp. In no case may the end of the insulation be crimped in the wire crimp; conversely, the insulation must extend at least to the front edge of the insulation crimp. B Crimpdaten für Isolationscrimp B Crimping data f or insulation crimp Die Crimpform, Crimpbreite und eine Empfehlung für die Crimphöhe sind in Tab. 1 aufgeführt. Die Crimphöhe wird nach der Biegeprüfung nach ehemaliger DIN 41611 Teil 3 oder der Wickelprüfung nach DIN EN 60352-2 eingestellt. The shape, width and reference value for the height of the crimp are shown in Table 1. The crimp height is set after the bending test to former DIN 41611 Part 3 or the winding test to DIN IEC 352 Part 2. 4.5 Kontaktbereich 4.5 Contact Area Überfeder mit Rastfeder sowie Kontaktkörper mit Kragen für Sekundärverriegelung dürfen durch den Crimpvorgang weder verbogen noch deformiert sein. After crimping, neither the cantilever spring with locking lances nor the contact body with collar for secondary retention may be bent or deformed.
4.6 Form- und Lagetoleranzen des gecrimpten
Kontaktes (siehe Bild 2)
4.6 Shape and Positional Tolerances of the
Crimped Contact (see Fig. 2) Bild 2 / Fig. 2 Trennsteg max. 0.3 / Cut off max. 0.3 Wichtig bei 0,75mm² / important at 0,75mm² max. 0,4 bei 0,75mm² oder Anw. m. Sammeldichtung/ max. 0,4 at 0,75mm² or family-seal application
5 CRIMPDATEN FÜR MQS (MICRO QUADLOK SYSTEM) /
5 CRIMPING DATA FOR MQS (MICRO QUADLOK SYSTEM)
Tabelle 1: Buchsen- und Stiftkontakte / Table 1 Socket- and pin contacts Bestellnummer / Order No. Isolations- ø / Insul. Range [mm] Leiter- quer- schnitt / Wire size [mm²] Abiso- lier- länge / Strip length ±0,15 [mm] Drahtcrimp / Wire crimp Isolationscrimp / Insulation crimp Aus- führung / Contact Band-ware/ Strip Einzelware / Loose piece Crimp- profil- breite / crimper profile width CB 1 [mm] Mess- bare Crimp- breite / measura ble crimp width CB m1 [mm] Höhe / Height CH 1 ±0,03 *±0,02 [mm] Form / Shape Crimp- profil- breite / crimper profile width [mm] Messbare Crimp- breite / measurable crimp width CB m2 [mm] Höhe / Height FLU CH 2 ±0,1 *±0,05 [mm] Höhe / Height FLR CH 2 ±0,1 [mm] Form / Shape Crimp- Werkzeug / Crimp tool Handcrimp- Werkzeug / Hand crimp tool FLU FLR Buchse / Socket Stift / Pin 2141824 2141828 2141825 2141829 -10) 0,85 - 1,00 0,13 8) 0,17 8) 3,7 1,02 (.040) 1,02 +0,1 0,68* 0,70* F 1,57 (.062) 1,57 ±0,2 -10) -10) 1,10 1,20 Umfas- sungscrimp / Enclosing Crimp O 2151326 1530498-6 3-1579014-9 Buchse / Socket Stift / Pin 1355717 1355719 1355718 1355720 0.95 – 1.05 0,85 - 1,20 0,08 0,14 0,20 0,22 3,7 1,07 (.042) 1,07+0,1 0,64 0,71 0,75 0,77 F 1,57 (.062) 1,57 ±0,2 -10) -10) -10) 1,25* 1,30 1,35 1,45 1,50 Umfas- sungscrimp / Enclosing Crimp O 2151265 x-541695-x x-541722-x5) 5-1579001-21) Buchse / Socket Stift / Pin 928999 968220 968893 1241918 1703296 2141400 928918 963726 968220 1355988 1241919 1703297 963725 1,10 - 1,20 1,10 - 1,60 0,25 0,35 (0,5) 3,6 1,4 4) (.055) 1,4 +0,15 0,72 0,76 (0,86) F 1,83 (.072) 1,83 ±0,2 -10) 1,40 (1,65) 3 1,40 1,50 (1,8) 3 Umfas- sungscrimp / Enclosing Crimp O 2151493 2151541 4) x-541578-x4) x-878439-x 539682-21) Buchse / Socket Stift 968221 963715 1241920 1452013 1703298 2141399 963716 968221 963729 1241921 1452014 1703299 963730 1,30 - 1,60 1,40 - 1,90 0,50 0,75 3,8 1,4 (.055) 1,4 +0,15 0,93 1,07 F 2,03 (.080) 2,03 ±0,2 1.45 1,80 1,70 2,05 Umfas- sungscrimp / Enclosing Crimp O 2151491 x-878591-x 3-1579001-51) 5-1579001-72) Buchse / Socket 6), 7) 1241920 1241921 1.30 – 1.40 1,40 - 1,60 0,50 3,8 1,4 1,83 Umfas- sungscrimp / Enclosing Crimp O 2151602 x-1528705- x7) -
austauschbarer Matrizensatz nur für ERGOCRIMP Basishandzange 539635-1 2) austauschbarer Crimpkopf für Basishandzange 2-1579005-1 3) Verwendung für DGB 0, 5mm² zulässig, bei bestehenden Sonderanwendungen, die mit der verantwortlichen Fachabteilung des Endkunden vereinbart wurden. Nicht für Neuanwendungen! 4) alternativ Drahtcrimpbreite 1,27 mm (.050) möglich: Crimphöhen siehe Werkzeugdokumentation. 5) speziell für Fa. Braun 6) Für den Kontakt 1241920 wird die Wahl des Crimpwerkzeugs von der Anwendung bestimmt. 7) Einschränkung für das Crimpwerkzeug x-1528705-x: - Nur für Kontakte zum Einsatz im 92+8-poligen Airbag - Steckverbinder mit Sammeldichtung, produziert von Yazaki, nach VW Zeichnung TAB 010 329 CB zu verwenden. - nur für 0,5mm² FLR - Leitung! - nur für Kontakt-Nr. 1241920 und 1703282 - Breite des angeschlagenen Kontaktes über die gesamte Länge max. 1,90mm Achtung: Die Verwendung des „falschen“ Crimpwerkzeu gs kann dazu führen, dass die angeschlagenen Kontakte nicht in die Gehäusekammern zu bestücken sind. 8) zugverstärkte Leitung nach LV 112-4 - LEONI CuSn 0,13mm² - Delphi CuMg 0,13mm² Coficab CuSn 0,13 mm² - Gebauer&Griller CuAg 0,17mm² 9) Empfehlung, siehe Kapitel 4.4 B 10) Kontakt-, Leitungskombination bisher nicht betrachtet 1) exchangeable die set only for ERGOCRIMP basic hand tool 539635-1 2) exchangeable die set only for Basic Hand tool 2-1579005-1 3) for existing application, wire size 0,5mm² is permitted, if agreed with responsible department of the final customer. Not for new applications!" 4) Alternative wire crimp width 1,27 mm (.050) possible: crimp height see tool documentation 5) Special for Co. Braun 6) for contact 1241920 the log get selected by application. 7) Restrictions for the log x-1528705-x - restricted for use of terminals in 92+8-way family sealed airbag connector manufactured by Yazaki according to VW drawing number TAB 010 329 CB - 0,5mm² wire size only! - terminals PN 1241920 and 1703282 only - width of terminal over entire length 1,90mm max. Attention: The use of „wrong“ log can prevent loading of contacts in the housing. 8) reinforced wire according to LV 112-4 - LEONI CuSn 0,13mm² - Delphi CuMg 0,13mm² - Coficab CuSn 0,13 mm² - Gebauer&Griller CuAg 0,17mm² 9) reference, see capture 4.4 B 10) Contact-, wire combination has not yet been considered
6 CRIMPDATEN FÜR MQS (MICRO QUADLOK SYSTEM 2-PUNKT) /
6 CRIMPING DATA FOR MQS (MICRO QUADLOK SYSTEM 2 -POINT)
Tabelle 2: Buchsenkontakte MQS 2-Punkt / Table 2 Socket Contacts MQS 2-Point Bestellnummer / Order No. Isolations- ø / Insul. Range [mm] Leiter- quer- schnitt / Wire size [mm²] Abiso- lier- länge / Strip length ±0,15 [mm] Drahtcrimp / Wire crimp Isolationscrimp / Insulation crimp Aus- führung / Contact Band- ware/ Strip Einzelware / Loose piece Crimp- profil- breite / crimper profile width CB 1 [mm] Mess- bare Crimp- breite / measura ble crimp width CB m1 [mm] Höhe / Height CH 1 ±0,03 *±0,02 [mm] Form / Shape Crimp- profil- breite / crimper profile width [mm] Messbare Crimp- breite / measurable crimp width CB m2 ±0,2 [mm] Höhe / Height FLU CH 2 ±0,1 [mm] Höhe / Height FLR CH 2 ±0,1 [mm] Form / Shape Crimp- Werkzeug / Crimp tool Handcrimp- Werkzeug / Hand crimp tool FLU FLR Buchse / Socket Rastfeder / Locking Lance 1394406 1394407 -10) 0,85 - 1,00 0,08 0,13 8) 0,14 0,17 8) 0,20 0,22 3,7 1,07 (.042) 1,07+0,1 0,64 0,71* 0,71 0,75* 0,75 0,77 F 1,57 (.062) 1,57 -10) -10) -10) -10) 1,30 1,25 1,35 1,25 1,45 1,50 Umfas- sungscrimp / Enclosing Crimp O x-541695-x x-541722-x5) 5-1579001-21) Buchse / Socket Clean- Body Rastfeder / Locking Lance 1534116 1394702 1534117 1394703 -10) 0,85 - 1,20 0,25 0,35 (0,5) 3,6 1,4 4) (.055) 1,4 +0,15 0,72 0,76 (0,86) F 1,83 (.072) 1,83 -10) 1,40 (1,65) 3 1,40 1,50 (1,8) 3 Umfas- sungscrimp / Enclosing Crimp O 2151493 x-541578-x4) x-878439-x 539682-21) Buchse / Socket Clean - Body 1703282 1703283 1,30 - 1,60 1,40 - 1,90 0,50 0,75 3,8 1,4 (.055) 1,4 +0,15 0,93 1,07 F 2,03 (.080) 2,03 1,45 1,80 1,70 2,05 Umfas- sungscrimp / Enclosing Crimp O 2151491 x-878591-x 3-1579001-51) 5-1579001-72) Buchse / Socket 6), 7) 1703282 1703283 1,30 - 1,40 1,40 - 1,60 0,50 3,8 1,4 1,83 Umfas- sungscrimp / Enclosing Crimp O 2151602 x-1528705- x7)
) austauschbarer Matrizensatz nur für ERGOCRIMP Basishandzange 539635-1 2) austauschbarer Crimpkopf für Basishandzange 2-1579005-1 3) Verwendung für DGB 0, 5mm² zulässig, bei bestehenden Sonderanwendungen, d ie mit der verantwortlichen Fachabteilung des Endkunden vereinbart wurden. Nicht für Neuanwendungen! 4) alternativ Drahtcrimpbreite 1,27 mm (.050) möglich: Crimphöhen siehe Werkzeugdokumentation. 5) speziell für Fa. Braun 6) Für den Kontakt 1703282 wird die Wahl des Crimpwerkzeugs von der Anwendung bestimmt. 7) Einschränkung für das Crimpwerkzeug x-1528705-x: - Nur für Kontakte zum Einsatz im 92+8-poligen Airbag - Steckverbinder mit Sammeldichtung, produziert von Yazaki, nach VW Zeichnung TAB 010 329 CB zu verwenden. - nur für 0,5mm² FLR - Leitung! - nur für Kontakt-Nr. 1703282 und 1241920 - Breite des angeschlagenen Kontaktes über die gesamte Länge max. 1,90mm Achtung: Die Verwendung des „falschen“ Crimpwerkzeugs kann dazu führen, dass die angeschlagenen Kontakte nicht in die Gehäusekammern zu bestücken sind. 8) zugverstärkte Leitung nach LV 112-4 - LEONI CuSn 0,13mm² - Delphi CuMg 0,13mm² - Coficab CuSn 0,13 mm² - Gebauer&Griller CuAg 0,17mm² 9) Empfehlung, siehe Kapitel 4.4 B 10) Kontakt-, Leitungskombination bisher nicht betrachtet 1) exchangeable die set only for EGROCRIMP basic hand tool 539635-1 2) exchangeable die set only for Basic Hand tool 2-1579005-1 3) for existing application, wire size 0,5mm² is permitted, if agreed with responsible department of the final customer. Not for new applications!" 4) alternative wire crimp width 1,27 mm (.050) possible: crimp height see tool documentation 5) special for Co. Braun 6) for contact 1703282 the log get selected by application. 7) restrictions for the log x-1528705-x: - restricted for use of terminals in 92+8-way family sealed airbag connector manufactured by Yazaki according to VW drawing number TAB 010 329 CB - 0,5mm² wire size only! - terminals PN’s 1703282 and 1241920 only - width of terminal over entire length 1,90 mm max. Attention: The use of „wrong“ log can prevent loading of contacts in the housing. 8) reinforced wire according to LV 112-4 - LEONI CuSn 0,13mm² - Delphi CuMg 0,13mm² - Coficab CuSn 0,13 mm² - Gebauer&Griller CuAg 0,17mm² 9) reference, see capture 4.4 B 10) Contact-, wire combination has not yet been considered T For some part numbers the insulation range and insulation crimp height for FLU wires added M.Brunner 09.08.2016 S measurable crimp width for PN1355717 and PN1394406 was 1,02 +0,1 should be 1,07 +0,1 M.Brunner 26.03.2015 R Note for column ISO CH added. Views of the crimped contacts (below the tables) corrected M.Brunner 27.11.2014 P Insulation crimp height for FLU wires added / Adaptation stripping length (table 1 + 2) M.Brunner 23.10.2014 N PN 2141832 and 2141834 removed; Note 8) completed; Ocean applicators added M.Brunner 22.04.2013 M Note 3) bei Tabelle 1 & 2 wieder hinzugefügt (customer request) M.Brunner 29.02.2012 L Logo geändert; Punkt 4.3 ergänzt; Tabelle 1 & 2 neue PN ergänzt M.Brunner 23.09.2011 H Tabellen auf Seite 11-14 ergänzt H.Kampmann 11.09 .2006 G Korrektur Tabelle 2 Seite 14 EC.: EGA0-2222-04 H. Kampmann 18.10.2004 F MQS 2-Punkt hinzugefügt EC.: EGA0-2199-04 H.Kampm ann 05.10.2004 E Crimphöhe für Handzange geändert EC.: EG00-1701-0 3 H.Kampmann 26.06.2003 D Spezifikation überarbeitet; PN hinzugefügt; EC: EG00-0498-03 H.Kampmann 12.02.2003 Rev. Aenderung erstellt Datum