408-32163 TEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be tra demarks of their respective owners. This controlled document is subject to change. visit our website at www.te.com.

09 FEB 15 Rev A

contacts. Read these instructions thoroughly before using the extraction tool kit. only and are not drawn to scale. each stacked row of the cage assembly). Figure 1. The top push plate is designed to be installed onto the upper tooling and the base plate is designed to

1 X 5 QSFP SFP+ Cage

During extraction, the back and sides of the extraction tool protect the cage assembly from damage, the wall supports support the individual ports of the cage assembly, and the top push plate provides a surface to apply an even force to extract the pc board from the connector and cage assembly. 3. APPLICATION TOOLING REQUIREMENT Power for the extraction tool must be provided by application tools (with a ram) capable of supplying a downward force of 44.5 N [10 lb] per contact. Manual Arbor Frame Assembly 58024-1 is available for use with these extraction tool kits. Refer to Instruction Sheet 408-6923 for operating procedure. CAUTION Over-driving of the extraction tool could cause damage to the connector or cage assembly. 4. EXTRACTION PROCEDURE 1. Ensure that the amount of wall supports installed onto the finger mounting block matches the amount of ports of the cage assembly. It is recommended to center the group of wall supports on the finger mounting block. Refer to Figure 1. 2. Install the top push plate onto the upper tooling and the base plate (with the wall supports) onto the lower tooling of the application tool. See Figure 2. CAUTION Ensure that the upper tooling and lower tooling are secure; otherwise, damage to the connector and cage assembly could occur. 3. Place the open end of the extraction tool over the cage assembly so that the cutouts align with the protruding part (at the back) of the cage assembly. Make sure that the sides of the extraction tool sit on the pc board. 4. Slide the extraction tool (with the connector and cage assembly and pc board) onto the wall supports so that each “finger” of each wall support enters a port of the cage assembly. Make sure the fingers are fully inserted into the ports. See Figure 2. Figure 2 5. Cycle the application tool to extract the pc board from the connector and cage assembly. Then retract the ram, and carefully remove the extraction tool (with the connector and cage assembly) from the wall supports. 5. MAINTENANCE AND INSPECTION The extraction tool kit is inspected before shipment. It is recommended that the extraction tool kit be inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment and that it conforms to the dimensions provided in Figure 3. Side View Application Tool Ram Fingers of Wall Supports Fully Inserted into Cage Assembly Base Plate (with Wall Supports) Lower Tooling of Application Tooling PC Board Top Push Plate Sides of Extraction Tool Sitting on PC Board

5.1. Daily Maintenance It is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use objects that could damage the extraction tool kits components. 2. When the extraction tool kit is not in use, store it in a clean, dry area. 5.2. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the extraction tool kit or be supplied to personnel responsible for the extraction tool kit. Inspection frequency should be based on amount of use, working conditions, operator training and skill, and established standards. 6. REPLACEMENT AND REPAIR Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by TE Connectivity to ensure quality and reliability. Order replacement parts through your TE Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 7. REVISION SUMMARY  Initial release of document Figure 3 (cont’d)

1 X 4 Extraction Tool Kit Shown

A 40.4 [1.591] 5.72 [.225] 43.22 [1.702] 142.85 [5.624] 101.6 [4.00] 40.4 [1.591] 50.8 [2.00] 50.8 [2.00] 25.4 [1.00] 41.80 [1.646] 40.00 [1.575]

TOOL (BY KIT PART NUMBER) DIMENSION “A” 2215058-1 19.45 [.766] 2215058-2 33.70 [1.327] 2215058-3 47.95 [1.888] 2215058-4 62.20 [2.449] 2215058-5 76.45 [3.010] 2215058-6 90.70 [3.571] ITEM NUMBER DESCRIPTION QTY PER TOOL

1 X 1 1 X 2 1 X 3 1 X 4 1 X 5 1 X 6

1 TOOL,

2 PLATE, Top

3 PLATE, Base 1 1 1 1 1 1

4 SUPPORT,

5 MOUNTING

BLOCK, Finger 1 1 1 1 1 1 ITEM NUMBER EXTRACTION TOOL KIT PART NUMBER 2215058-1 2215058-2 2215058-3 2215058-4 2215058-5 2215058-6 1 2215059-1 2215059-2 2215059-3 2215059-4 2215059-5 2215059-6 2 211356-1 3 2161354-1 4 2215638-1 5 2215637-1 Figure 3 (end)