1D0515

1D0515 AGELECTRONICA | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 7

Technical content

http://www.agelectronica.com 1D0515 CONVERTIDOR DC-DC ENTRADA 5V SALIDA 15V 67mA 1W 1W- 5V micropower module selection table MULTIPLESPECIFICATIONSAVAILABLE 5Vconstantvoltage(±10%Vin)input/1Wisolationunregulatedoutput MODEL POWER VOLTAGE Electricity HLK-1D0503 1W 3.3V 303mA HLK-1D0505 1W 5V 200mA HLK-1D0512 1W 12V 83mA HLK-1D0515 1W 15V 67mA HLK-1D0524 1W 24V 42mA *Theappearanceandpinsizeofthesameseriesofproductsarethesame *Internationalstandardpinsize11.5x10x6mm product features PRODUCTFEATURES  Ultra-miniaturestandardpackageSIPpackageandstandardpins  Constantvoltageinput(±10%Vin),isolatedunregulatedsingleoutput,1W  Ultra-lowstandbypowerconsumption,inputandoutputisolationwithstandvoltage1500VDC  Lowripplenoise(20MHbandwidth)<100mVp-p  Highefficiency, conversionefficiencyupto80%(MAX)  Operatingtemperaturerange:-40°C~+85°C  Goodoutputshortcircuitandovercurrentprotectionandself-recovery  Highreliability,longlifedesign,MTBF≥3500000H  Potting and sealing with high-quality environmentally friendly waterproof and thermal conductiveglue,dustproof,moistureproof,shockproofandflameretardant  MeetUL/CE/EMCandsafetytestingrequirements  Can be used in medical, industrial control, electric power, instrumentation, communication, railwayandotherfields

http://www.agelectronica.com Product characteristic curve PRODUCTCHARACTERISTICSCURVE

http://www.agelectronica.com Typical application circuit APPLICATIONCIRCUIT Recommended test circuit If it is required to further reduce the input and output ripple, a capacitor filter network can be connectedtotheinputandoutputends.Theapplicationcircuit isshowninthefigure. But care should be taken to select a suitable filter capacitor. If the capacitance is too large, it may causestartup problems. For each output, underthecondition of ensuring safe andreliable operation, therecommendedcapacitiveloadvalueisshownintheattachedtable. Recommendedcapacitiveloadvaluesaredetailed(Table1)

http://www.agelectronica.com EMI typical application circuit Recommended parameters: RecommendedEMIreferencecircuitvaluesaredetailed(Table2) Output load requirement In order to ensure that the module can work efficiently and reliably, when in use, its minimum output load cannot be less than 10% of the rated load. If the power you need is really small, please connect a resistor in parallel between the positive and negative poles of the output terminal (the sum of the actual power used by the resistors is greater than or equal to 10% of the rated power and the rated power of the selected resistor must be greater than 5 times the actual power used. , Otherwise the temperatureoftheresistorwillbehigher).

http://www.agelectronica.com Ripple & noise test: twisted pair method 20MHz bandwidth testing method: 1.Ripplenoiseisconnectedusing12#twistedpair,theoscilloscopebandwidthissetto20MHz, 100Mbandwidthprobe,and0.1uFpolypropylenecapacitorand47uFhighfrequencylowresistance electrolyticcapacitorareconnectedinparalleltotheprobeend,andtheoscilloscopesamplinguses Samplesamplingmode. 2.Connectthepowerinputterminaltotheinputpowersupply,andconnectthepoweroutputtothe electronicloadthroughthefixtureboard.Usea30cm±2cmsamplinglinetosampledirectlyfromthe poweroutputportfortesting.Thepowerlineselectsthecorrespondingwirediameterwirewith insulationaccordingtotheoutputcurrent.(AsshowninFIG)

http://www.agelectronica.com Product application notes PRODUCTAPPLICATIONNOTES 1. Input requirements: ensure that the output voltage fluctuation range of the power supply does not exceed the input requirements of the DC/DC module itself, and the output power of the input power supplymustbegreaterthantheoutputpoweroftheDC/DCmodule; 2. Recommended circuit 1: For occasions with general requirements for ripple and noise, a filter capacitor can be connected in parallel to the input and output ends. The external circuit is shown in the above figure (1). The recommended value of the filter capacitor is shown in Table (1) ). Output load requirements: Try to avoid no-load use. When the actual power consumption of the load is less than 10% of the module's output rated power or there is no-load phenomenon, it is recommended to connect a dummy load to the output end. The dummy load (resistance) can be in accordance with theratedpowerofthemodule.5~10%calculation,resistancevalue=Uout/(1W*10%); 3. Overload protection: Under normal working conditions, the output circuit of this product has no protection against overload. The easiest way is to connect a self-recovery fuse in series at the input end,oraddacircuitbreakertothecircuit; 4. The capacitance value of the external capacitor at the output end should not be too large, otherwiseitwilleasilycauseovercurrentorpoorstartupwhenthemodulestarts; 5. If the product works below the minimum required load, it cannot be guaranteed that the product performancemeetsalltheperformanceindicatorsinthismanual; 6.Themaximumcapacitiveloadistestedundertheinputvoltagerangeandfullloadconditions; 7. Except for special instructions, all indicators in this manual are measured at Ta=25℃/humidity <75%RH,nominalinputvoltageandoutputratedload; 8.Allindextestmethodsinthisproductmanualarebasedonourcompany'sstandards; 9. Our company can provide product customization, and you can directly contact our technical staff forspecificinformation; 10.Productspecificationsaresubjecttochangewithoutnotice.

http://www.agelectronica.com Dimensions DIMENSIONS Pin description: 1:GND;2:+Vin;3:-Vo 4:+Vo ; *Note: If the definition of each pin of the power module is not consistent with the selection manual, themarkingonthephysicallabelshallprevail. República del Salvador N° 20 Segundo Piso Teléfono: 55 5130 - 7210 ACOTACIÓN: N/A http://www.agelectronica.com ESCALA: N/A REALIZO: OGJ REV: JFRR TOLERANCIA: N/A CONVERTIDOR DC-DC ENTRADA 5V SALIDA 15V 67mA 1W TOLERANCIA: N/A Fecha: 06/06/2022 No. Parte: 1D0515