408-32241 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
1 of 3 © 2016 TE Connectivity family of companies All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names m ay be trademarks of their respective owners. PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com. 408-32241
18 MAR 16 Rev A
REMOVAL KIT NUMBER WILL REMOVE PRODUCT PART NUMBER 2215082-1 5-Pair 10 Column 1934932-1 Figure 1 1. INTRODUCTION Removal Kits 2215082-1 is designed to remove Z-PACK TinMan receptacle from printed circ uit (pc) boards. Refer to Figure 1. Read and understand these instructions before using the removal tools. 2. DESCRIPTION Each kit consists of two clamp subassemblies, a pusher subassembly, a guide module pusher plate, two pusher plate shims, and four pusher plate mounting screws. The clamp subassemblies consist of a front clamp plate, a rear clamp plate, and a clamp knob. The pusher subassembly consists of a top plate, tw o pusher plates, and a removal knob. The clamp subassembly clamps the receptacle while the pusher subassembly removes the receptacle from the pc board. The guide module pusher plate is used when the receptacle is adjacent to a guide module, and the pusher plate shims are used depending on the width of the receptacl e. 3. OPERATION 3.1. Tool Preparation To prepare the removal tool, know the dimension of the receptacle (number of rows and columns) and the placement of the receptacle (what is next to the receptacle). Once these conditions are determined, the tool can be prepared to remove the receptacle. To prepare the tool: 1. Select the kit part number to be used based on the receptacle part number or size. 2. Select the proper clamp subassembly for the receptacle part number or size. 3. Determine if shims are necessary and install as needed. See Figure 2 for shim placement. 4. Select the proper side pusher plate orientation, or select the guide module pusher plate, and instal l the side pusher plates. Refer to Figure 2 for pusher plate orientation. a. If a receptacle is located next to the clamp assembly, the pusher plate must have a horizontal orientation. b. If a printed circuit (pc) board is located next to the clamp assembly, the pusher plate must have a vertical orientation. Removal Kit 2215082-1 for Z-Pack TinMan* Receptacles Removal Knob Clamp Knob Pusher Plate Front Clamp Plate ORIGINAL INSTRUCTIONS
The tool and receptacle can spin after removal due to the twisting action of the removal knob. This spin could cause damage to the pc board. Hold the tool firmly during removal. 6. Remove the receptacle from the tool by loosening the Clamp Knob. 4. MAINTENANCE AND INSPECTION TE Connectivity recommends that the tool be inspected immediately upon its arrival to ens ure that it has not been damaged during shipment. 4.1. Daily Maintenance It is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: Remove dust, moisture, and other contaminants with a clean, soft brush, or lint-free cloth. DO NOT use objects that could damage the tool or any of its components. When the tool is not in use, store it in a clean, dry area. 4.2. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of schedu led inspections should remain with the tool or be supplied to personnel responsible for the tool. The inspection frequency should be based on the amount of use, working conditions, operator training and skill, and established company standards. 5. REPLACEMENT AND REPAIR Order tools through your TE Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605 or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 6. REVISION SUMMARY Initial release of document