18KBXCA-E4

18KBXCA MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

MODEL: 18KBXCA http://www.m-system.co.jp/ 18KBXCA SPECIFICATIONS ES-0497 Rev.0 Page 1/4 Rack-mounted DCS Signal Conditioners 18K-RACK STANDARD RACK (pressure supply) Functions & Features

• Standard 19" rack for 18K-RACK signal conditioners and I/P transducer (model: 18VP)
• Other 18-Rack signal conditioners are also mountable
• Module can be retracted without removing wiring for an insulation test
• Line power supplied via the rear rack bus
• Supply pressure at the manifold plug
• Direct interface to various DCS with the rack side connector MODEL: 18KBXCA–[1][2]

ORDERING INFORMATION

• Code number: 18KBXCA-[1][2] Specify a code from below for each [1] and [2]. (e.g. 18KBXCA-Y1/W) [1] CONNECTOR 0: None U1: Fujitsu FCN type I/O connector Y1: Yokogawa DCS MAC2 / PAC card use Y2: Yokogawa DCS VMx / PM1 card use E4: Toshiba DCS VTBU card use M-System guarantees the connecting section. [2] OPTIONS Mounting Bracket blank: Rack mounting, standard /W: Surface mounting

RELATED PRODUCTS

• Blank filler plate (model: P-181)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN) GENERAL SPECIFICATIONS Construction: Metal plates assembly Coating: Colored Zn-Cr Capacity: 16 positions Connection Power input: M4 screw terminals (torque 0.8 N·m) Field terminal: M3.5 screw terminals (torque 0.8 N·m) Pneumatic: Rc 3/8" female (torque ≤ 12 N·m) Screw terminal Power: Nickel-plated brass Field terminal: Nickel-plated steel Manifold: Aluminium alloy Isolation: I/O connector to field terminal to power to FG INSTALLATION Supply pressure: Refer to the data sheet for I/P transducers Power input
• DC: Operating voltage range 24 V DC ±10 %, 2.5 A minimum (ripple 10 % p-p max.) Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: JIS or EIA standard rack or surface Weight: 6 kg (13.2 lb) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (I/O connector to field terminal to power)

1000 V AC @ 1 minute (I/O connector or field terminal or

power to FG) Maximum supply pressure: 196 kPa (2 kgf/cm2, 1.96 bar, 28 psig)

MODEL: 18KBXCA http://www.m-system.co.jp/ 18KBXCA SPECIFICATIONS ES-0497 Rev.0 Page 2/4 MOUNTING REQUIREMENTS unit: mm (inch) 101.6 (4.00) * 450 (17.72) 465 (18.31) 4–M5 SCREW ANGLE BRACKET Observe an appropriate wiring space over and below. 100 (3.94) for JIS standard CONNECTION DIAGRAM FG 3 CN1 CN2 POWER SUPPLY PRESSURE Note 1: CN1 and CN2 are not available without connector. Note 2: CN2 is only available with

• Fujitsu FCN type I/O connector
• Y okogawa DCS MAC2 / PAC card use FIELD TERMINALS

MODEL: 18KBXCA http://www.m-system.co.jp/ 18KBXCA SPECIFICATIONS ES-0497 Rev.0 Page 3/4 DIMENSIONS unit: mm (inch) 2 (.08) 435 (17.13) 134 (5.28) 2 (.08) ■ RACK (standard) ■ SURFACE (option /W) 465 (18.31) 480 (18.90) 170 (6.69) 101.6 (4.00) 8.2 (.32) 64−M3.5 FIELD TERMINAL* 1 2 1 2 1 2 3 4 3 4 3 4 1ch 15ch 16ch 1 3 15 2 14 16 15 14 16 *Field I/O Terminal Block 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 8.5 (.33) CN2 CONNECTOR SUPPLY CONNECTION Rc 3 /8” 3−M4 POWER TERMINAL CN1 I/O CONNECTOR PIN ASSIGNMENT Fujitsu FCN type I/O connector (Fujitsu FCN-365P040-AU) Connector Pin Assignment CN1: output 1 or input CN2: output 2 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A 1 ch. 1 + B 1 ch. 1 – A 2 ch. 2 + B 2 ch. 2 – A 3 ch. 3 + B 3 ch. 3 – A 4 ch. 4 + B 4 ch. 4 – A 5 ch. 5 + B 5 ch. 5 – A 6 ch. 6 + B 6 ch. 6 – A 7 ch. 7 + B 7 ch. 7 – A 8 ch. 8 + B 8 ch. 8 – A 9 ch. 9 + B 9 ch. 9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused Pin assignment is common to both CN1 and CN2. Yokogawa DCS MAC2 / PAC card use (PS-40PE-D4LT1-PN1) Location CN1: MAC2 / PAC card use* CN2: MAC2 / PAC card use* (for redundancy) The input or output 1 is connected to the connector. 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 i o i o i o i o i o i o i o i o MAC2/PAC CARD I/O (i = input, o = output) *MAC2 card (uses KS1 cable) I/O card used for control I/O. Composed of 8 inputs and 8 outputs. Input and output are paired. (Replace with pulse inputs for PAC card.)

MODEL: 18KBXCA http://www.m-system.co.jp/ 18KBXCA SPECIFICATIONS ES-0497 Rev.0 Page 4/4 Yokogawa DCS VMx / PM1 card use (PS-40PE-D4LT1-PN1) Location CN1: VMx / PM1 card use* The input or output 1 is connected to the connector. 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. *VMx / PM1 card (uses KS2 cable) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 19 ch. 1 – 2 ch. 2 + 20 ch. 2 – 3 ch. 3 + 21 ch. 3 – 4 ch. 4 + 22 ch. 4 – 5 ch. 5 + 23 ch. 5 – 6 ch. 6 + 24 ch. 6 – 7 ch. 7 + 25 ch. 7 – 8 ch. 8 + 26 ch. 8 – 9 ch. 9 + 27 ch. 9 – 10 ch.10 + 28 ch.10 – 11 ch.11 + 29 ch.11 – 12 ch.12 + 30 ch.12 – 13 ch.13 + 31 ch.13 – 14 ch.14 + 32 ch.14 – 15 ch.15 + 33 ch.15 – 16 ch.16 + 34 ch.16 – Toshiba DCS VTBU card use (57LE-40360-7700) • Connector Pin Assignment CN1: VTBU card use The output 1 is connected to the connector. 17, 18, 35 and 36: Unused Specifications are subject to change without notice.