18BXCA-1K2/W

18BXCS MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

MODEL: 18BXCS http://www.m-system.co.jp/ 18BXCS SPECIFICATIONS ES-1807 Rev.7 Page 1/4 Rack-mounted DCS Signal Conditioners 18-RACK STANDARD RACK (with grounding bar) Functions & Features

• Standard 19" rack for 18-RACK signal conditioners
• Line power supplied via the rear rack bus
• Grounding bar
• Direct interface to various DCS with the rack connector MODEL: 18BXCS–1[1]

ORDERING INFORMATION

• Code number: 18BXCS-1[1] Specify a code from below for [1] (e.g. 18BXCS-1Y3) FUNCTION 1: Power distribution & grounding [1] CONNECTOR U1: Fujitsu FCN type I/O connector Y1: Yokogawa DCS VMx / PM1 card use Y3: Yokogawa DCS MAC2 / PAC card use M-System guarantees the connecting section.

RELATED PRODUCTS

• Blank filler plate (model: P-181)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN) GENERAL SPECIFICATIONS Construction: Metal plates assembly Coating: Colored Zn-Cr Capacity: 16 positions Connection Power input: M4 screw terminals (torque 0.8 N·m) Ground: M3.5 screw terminals (torque 0.8 N·m) Shield: M3.5 screw terminals (torque 0.8 N·m) Screw terminal
• Power input: Nickel-plated brass
• Ground: Chromated steel
• Shield: Chromated steel INSTALLATION Power input
• DC: Operating voltage range 24 V DC ±10 %, 2.5 A minimum (ripple 10 % p-p max.) Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: JIS or EIA standard rack Weight: 3 kg (6.61 lbs) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC (I/O connector to power to FG) Dielectric strength:

500 V AC @ 1 minute (I/O connector to power)

1000 V AC @ 1 minute (I/O connector or power to FG)

MODEL: 18BXCS http://www.m-system.co.jp/ 18BXCS SPECIFICATIONS ES-1807 Rev.7 Page 2/4 MOUNTING REQUIREMENTS Observe appropriate wiring space over and under the rack. 450 (17.72) 4–M5 SCREW 465 (18.31) 57.2 (2.25) < EIA > 15 (.59) 50 (1.97) < JIS > ANGLE BRACKET CONNECTION DIAGRAM POWER FG EARTH GND BAR CN1 CN2 * * CN2 is connectable only with:

• Fujitsu FCN type I/O connector
• Y okogawa DCS MAC2 / PAC card use DIMENSIONS unit: mm (inch) 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 465 (18.31) 50 (1.97) 15 (.06) 57.2 (2.25) 480 (18.90) 439 (17.28) 8.5 (.33) CN2 5–M4 POWER TERMINAL CN1 5 131 6 14 12 2 (.08) GROUND BAR MTG SCREW (2–M4) SHIELD TERMINALS (16–M3.5 SCREW) GROUND TERMINAL (M3.5 SCREW) GROUND BAR INSULATION

MODEL: 18BXCS http://www.m-system.co.jp/ 18BXCS SPECIFICATIONS ES-1807 Rev.7 Page 3/4 I/O CONNECTOR PIN ASSIGNMENT Fujitsu FCN type I/O connector (Fujitsu FCN-365P040-AU) Connector Pin Assignment CN1: output 1 or input CN2: output 2 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A 1 ch. 1 + B 1 ch. 1 – A 2 ch. 2 + B 2 ch. 2 – A 3 ch. 3 + B 3 ch. 3 – A 4 ch. 4 + B 4 ch. 4 – A 5 ch. 5 + B 5 ch. 5 – A 6 ch. 6 + B 6 ch. 6 – A 7 ch. 7 + B 7 ch. 7 – A 8 ch. 8 + B 8 ch. 8 – A 9 ch. 9 + B 9 ch. 9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused Pin assignment is common to both CN1 and CN2. Yokogawa DCS VM ❑ / PM1 card use (PS-40PE-D4LT1-PN1) Location CN1: VM ❑ / PM1 card use* The input or output 1 is connected to the connector. 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. *VM❑ / PM1 card (uses KS2 cable) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points Specifications subject to change without notice. Yokogawa DCS MAC2 / PAC card use (PS-40PE-D4LT1-PN1) Location CN1: MAC2 / PAC card use* CN2: MAC2 / PAC card use* (for redundancy) The input or output 1 is connected to the connector. 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 i o i o i o i o i o i o i o i o MAC2/PAC CARD I/O (i = input, o = output) *MAC2 card (uses KS1 cable) I/O card used for control I/O. Composed of 8 inputs and 8 outputs. Input and output are paired. (Replace with pulse inputs for PAC card.)

MODEL: 18BXCS http://www.m-system.co.jp/ 18BXCS SPECIFICATIONS ES-1807 Rev.7 Page 4/4 Specifications are subject to change without notice.