18BXC-1K1

18BXC MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

MODEL: 18BXC http://www.m-system.co.jp/ 18BXC SPECIFICATIONS ES-1892 Rev.13 Page 1/5 Rack-mounted DCS Signal Conditioners 18-RACK STANDARD RACK Functions & Features

• Standard 19" rack for 18-RACK signal conditioners
• Line power access at the terminal card, supplied via the rear rack bus
• Direct interface to various DCS with the rack side connector MODEL: 18BXC–1[1][2]

ORDERING INFORMATION

• Code number: 18BXC-1[1][2] Specify a code from below for [1] and [2] (e.g. 18BXC-11/W) FUNCTION 1: Power distribution [1] CONNECTOR 1: Fujitsu FCN type I/O connector 2: Yokogawa VMx / PM1 card use 3: Yokogawa MAC2 / PAC card use H1: Hitachi DCS EX connector H2: Hitachi DCS EX-CDL cable connector E5: Toshiba DCS VAIMX1 card use E6: Toshiba DCS VAOPX1 card use K1: Yamatake DCS AI connector K2: Yamatake DCS AO connector K5: Yamatake DCS PI connector V1: Shimadzu DCS connector M-System guarantees the connecting section. [2] OPTIONS Mounting Bracket blank: Rack mounting, standard /W: Surface mounting

RELATED PRODUCTS

• Blank filler plate (model: P-181)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN) GENERAL SPECIFICATIONS Construction: Metal plates assembly Coating: Colored Zn-Cr Capacity: 16 positions Connection Power input: M4 screw terminals (torque 0.8 N·m) Screw terminal: Nickel-plated brass INSTALLATION Power input
• DC: Operating voltage range 24 V DC ±10 %, 2.5 A minimum (ripple 10 % p-p max.) Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: JIS or EIA standard rack or surface Weight: 1.7 kg (3.7 lbs) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC (I/O connector to power to FG) Dielectric strength:

500 V AC @ 1 minute (I/O connector to power)

1000 V AC @ 1 minute (I/O connector or power to FG)

MODEL: 18BXC http://www.m-system.co.jp/ 18BXC SPECIFICATIONS ES-1892 Rev.13 Page 2/5 MOUNTING REQUIREMENTS Observe appropriate wiring space over and under the rack. 450 (17.72) 4–M5 SCREW 465 (18.31) 57.2 (2.25) < EIA > 15 (.59) 50 (1.97) < JIS > ANGLE BRACKET CONNECTION DIAGRAM POWER FG CN1 CN2 CN2 is connectable with: ɹɹ • Fujitsu FCN type I/O connector ɹɹ • Y okogawa DCS MAC2/PAC card use ɹɹ • Hitachi DCS EX connector ɹɹ • Toshiba DCS VAOPX1 card use ɹɹ • Y amatake DCS PI connector DIMENSIONS unit: mm (inch) 5 131 6 14 12 15 14 16 2 (.08) 435 (17.13) 134 (5.28) 2 (.08) ■ RACK (standard) ■ SURFACE (option /W) 465 (18.31) 110 (4.33) 50 (1.97) 57.2 (2.25) 480 (18.90) 8.5 (.33) CN2 CN1 15 (.06) 5–M4 POWER TERMINAL 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16

MODEL: 18BXC http://www.m-system.co.jp/ 18BXC SPECIFICATIONS ES-1892 Rev.13 Page 3/5 I/O CONNECTOR PIN ASSIGNMENT Fujitsu FCN type I/O connector (Fujitsu FCN-365P040-AU) Connector Pin Assignment CN1: output 1 or input CN2: output 2 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A 1 ch. 1 + B 1 ch. 1 – A 2 ch. 2 + B 2 ch. 2 – A 3 ch. 3 + B 3 ch. 3 – A 4 ch. 4 + B 4 ch. 4 – A 5 ch. 5 + B 5 ch. 5 – A 6 ch. 6 + B 6 ch. 6 – A 7 ch. 7 + B 7 ch. 7 – A 8 ch. 8 + B 8 ch. 8 – A 9 ch. 9 + B 9 ch. 9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused Pin assignment is common to both CN1 and CN2. Yokogawa DCS VM ❑ / PM1 card use (PS-40PE-D4LT1-PN1) Location CN1: VM ❑ / PM1 card use* The input or output 1 is connected to the connector. 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. *VM❑ / PM1 card (uses KS2 cable) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points Specifications subject to change without notice. Yokogawa DCS MAC2 / PAC card use (PS-40PE-D4LT1-PN1) Location CN1: MAC2 / PAC card use* CN2: MAC2 / PAC card use* (for redundancy) The input or output 1 is connected to the connector. 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 i o i o i o i o i o i o i o i o MAC2/PAC CARD I/O (i = input, o = output) *MAC2 card (uses KS1 cable) I/O card used for control I/O. Composed of 8 inputs and 8 outputs. Input and output are paired. (Replace with pulse inputs for PAC card.) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 9 ch. 9 + 19 ch. 1 – 27 ch. 9 – 2 ch. 2 + 10 ch.10 + 20 ch. 2 – 28 ch.10 – 3 ch. 3 + 11 ch.11 + 21 ch. 3 – 29 ch.11 – 4 ch. 4 + 12 ch.12 + 22 ch. 4 – 30 ch.12 – 5 ch. 5 + 13 ch.13 + 23 ch. 5 – 31 ch.13 – 6 ch. 6 + 14 ch.14 + 24 ch. 6 – 32 ch.14 – 7 ch. 7 + 15 ch.15 + 25 ch. 7 – 33 ch.15 – 8 ch. 8 + 16 ch.16 + 26 ch. 8 – 34 ch.16 – Pin assignment is common to both CN1 and CN2. Hitachi DCS EX connector (DN10-36S) • Connector Pin Assignment CN1 : output 1 CN2 : output 2

MODEL: 18BXC http://www.m-system.co.jp/ 18BXC SPECIFICATIONS ES-1892 Rev.13 Page 4/5 Hitachi DCS EX-CDL cable connector Connector Pin Assignment CN1 : output 1 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 9 ch. 9 + 19 ch. 1 – 27 ch. 9 – 2 ch. 2 + 10 ch.10 + 20 ch. 2 – 28 ch.10 – 3 ch. 3 + 11 ch.11 + 21 ch. 3 – 29 ch.11 – 4 ch. 4 + 12 ch.12 + 22 ch. 4 – 30 ch.12 – 5 ch. 5 + 13 ch.13 + 23 ch. 5 – 31 ch.13 – 6 ch. 6 + 14 ch.14 + 24 ch. 6 – 32 ch.14 – 7 ch. 7 + 15 ch.15 + 25 ch. 7 – 33 ch.15 – 8 ch. 8 + 16 ch.16 + 26 ch. 8 – 34 ch.16 – PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 9 ch. 9 + 19 ch. 1 – 27 ch. 9 – 2 ch. 2 + 10 ch.10 + 20 ch. 2 – 28 ch.10 – 3 ch. 3 + 11 ch.11 + 21 ch. 3 – 29 ch.11 – 4 ch. 4 + 12 ch.12 + 22 ch. 4 – 30 ch.12 – 5 ch. 5 + 13 ch.13 + 23 ch. 5 – 31 ch.13 – 6 ch. 6 + 14 ch.14 + 24 ch. 6 – 32 ch.14 – 7 ch. 7 + 15 ch.15 + 25 ch. 7 – 33 ch.15 – 8 ch. 8 + 16 ch.16 + 26 ch. 8 – 34 ch.16 – Toshiba DCS VAIMX1 card use (57LE-40360-7700) • Connector Pin Assignment CN1: output 1 Toshiba DCS VAOPX1 card use (57LE-40360-7700) Connector Pin Assignment CN1, CN2: input CN1 PIN NO. ASSIGNMENT CN2 PIN NO. ASSIGNMENT 1 ch. 1 + 1 ch. 9 + 19 ch. 1 – 19 ch. 9 – 3 ch. 2 + 3 ch.10 + 21 ch. 2 – 21 ch.10 – 5 ch. 3 + 5 ch.11 + 23 ch. 3 – 23 ch.11 – 7 ch. 4 + 7 ch.12 + 25 ch. 4 – 25 ch.12 – 9 ch. 5 + 9 ch.13 + 27 ch. 5 – 27 ch.13 – 11 ch. 6 + 11 ch.14 + 29 ch. 6 – 29 ch.14 – 13 ch. 7 + 13 ch.15 + 31 ch. 7 – 31 ch.15 – 15 ch. 8 + 15 ch.16 + 33 ch. 8 – 33 ch.16 – Yamatake DCS AI connector • Location Input connector : 57LE-40500-7300 CN1: AI use 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 YAMATAKE DCS AI CARD (J-HAM50/HMM00) INPUT Yamatake DCS AO connector • Location Output connector : 57LE-40500-7300 CN1: AO use 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 YAMATAKE DCS AO CARD (J-AOM10) OUTPUT 18-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 YAMATAKE DCS PI CARD YAMATAKE DCS PI CARD (J-PIM00) INPUT NO. (J-PIM00) INPUT NO. Yamatake DCS PI connector • Location Output connector : 57LE-40500-7300 CN1 : PI use PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A1 ---- B1 ch.1 thr. 16 – A2 ch. 1 + B2 ch. 2 + A3 ch. 3 + B3 ch. 4 + A4 ch. 5 + B4 ch. 6 + A5 ch. 7 + B5 ch. 8 + A6 ch. 9 + B6 ch.10 + A7 ch.11 + B7 ch.12 + A8 ch.13 + B8 ch.14 + A9 ch.15 + B9 ch.16 + A10 ch.1 thr. 16 – B10 ---- A1 and B10 are shortcircuited. Shimadzu DCS connector (HIF3BA-20PA-2.54DS) Connector Pin Assignment CN1 : output 1

MODEL: 18BXC http://www.m-system.co.jp/ 18BXC SPECIFICATIONS ES-1892 Rev.13 Page 5/5 Specifications are subject to change without notice.