DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Instruction SheetCERTI- CRIMP* II Tool Holder Assembly 1213860- 1 (for Use with the SDE Electric 408- -10021 LOC B 1 of 5E2010 Tyco Electronics Corporation, Berwyn, PA All Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other product names, logos, or company names might be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1- -800- -722- -1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.tycoelectronics.com
16 MAR 10 Rev CBench Terminator)
1213860- -1 (for use with the SDE Electric Bench Terminator) SDE Electric Bench Terminator 1. INTRODUCTION The CERTI- -CRIMP II Tool Holder Assembly 1213860- -1 is used to adapt the crimping head from a CERTI- -CRIMP II Hand Tool to an SDE Electric Bench Terminator. Figure 1 shows a typical crimping head, mounted to CERTI- -CRIMP II Tool Holder Assembly 1213860- -1, installed onto an SDE Electric Bench Terminator. Figures and illustrations are for reference only, and are not to scale. This instruction sheet provides: S Instructions for installing and removing the tool holder assembly to the Electric Bench Machine S Instructions for installing the crimping head onto the tool holder assembly S Instructions for adjusting the crimp height S Maintenance, inspection, and repair instructions for the tool holder assembly For information concerning the setup and operation of the SDE Electric Bench Terminator, refer to customer manual 409- -10052. Read this instruction sheet, and the related customer manual, thoroughly before using the tool holder assembly. 2. DESCRIPTION The tool holder assembly facilitates the connection of the crimping head to the SDE Electric Bench Machine and provides the necessary straight line motion of the movable die when the SDE Electric Bench Machine is actuated. The tool holder assembly features a switch (handle) and three quick pins. See Figure 2. The switch (handle) can be used to manually open and close the dies of the crimping head for insertion and removal of the product. The two outer quick- -release pins secure the outer tabs of the crimping head to the tool holder assembly, and the center quick- -release pin secures the the movable die of the crimping head to the internal spring- -loaded switch of the tool holder assembly. ORIGINAL INSTRUCTIONS NOTE i
408- 10021CERTI- CRIMP II Tool Holder Assembly 1213860- 1 5 of 5Rev C Tyco Electronics Corporation 4 5 11 12 CUSTOMER- -REPLACEABLE PARTS ITEM PART NUMBER DESCRIPTION QTY PER ADAPTER 1 1213854- -1 HOUSING CENTER 2 2 1213859- -1 ECCENTRIC 1 3 1213856- -1 HANDLE, (Switch) 1 4 217873- -1 PIN, Quick Release 2 5 217873- -2 PIN, Quick Release 1 6 1213858- -1 PLUNGER 1 7 1213861- -1 POST, Spring Stop 1 8 1213857- -1 RAM 2 9 1213853- -1 HOUSING SIDE 2 10 18024- -7 SCREW, Btn Skt Hd Cap (M4 X 10.0) 4 11 18024- -8 SCREW, Btn Skt Hd Cap (M4 X 12.0) 4 12 18023- -4 SCREW, Skt Hd Cap, M3 X 10.0 2 13 22280- -9 SPRING, Compression 1 14 6- -22278- -0 SPRING, Compression 1 Figure 7