17AC

17AC MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

MODEL: 17AC http://www.m-system.co.jp/ 17AC SPECIFICATIONS ES-2936 Rev.0 Page 1/3 Rack-mounted Power Transducers 17-RACK AC CONVERTER Functions & Features

• Converting an alternating current/voltage into a standard process signal
• True RMS sensing Typical Applications
• Converting a large AC current in combination with a shunt resistor, or a narrow span AC voltage MODEL: 17AC–[1]6-R

ORDERING INFORMATION

• Code number: 17AC-[1]6-R Specify a code from below for [1]. (e.g. 17AC-A16-R)
• Special input range (For codes AZ & A8) [1] INPUT Current AA: 0 – 10 mA AC (Input resistance 100 Ω) AB: 0 – 50 mA AC (Input resistance 20 Ω) AC: 0 – 100 mA AC (Input resistance 10 Ω) AD: 0 – 500 mA AC (Input resistance 1 Ω) AZ: Specify current (See INPUT SPECIFICATIONS) (0 % input must be 0 mA.) Voltage A1: 0 – 100 mV AC (Input resistance 200 kΩ min.) A2: 0 – 500 mV AC (Input resistance 200 kΩ min.) A3: 0 – 1 V AC (Input resistance 200 kΩ min.) A4: 0 – 5 V AC (Input resistance 200 kΩ min.) A5: 0 – 10 V AC (Input resistance 200 kΩ min.) A6: 0 – 120 V AC (Input resistance 200 kΩ min.) A7: 0 – 150 V AC (Input resistance 200 kΩ min.) A8: Specify voltage (See INPUT SPECIFICATIONS) (0 % input must be 0 V.) OUTPUT Voltage 6: 1 – 5 V DC (Load resistance 2000 Ω min.) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals on the front and connector on the rear; terminal cover provided Connection: Input: M3.5 screw terminals (torque 0.8 N·m) Output: Connector Power input: Supplied from connector Screw terminal: Nickel-plated steel Isolation: Input to output to power Input waveform: Up to 15 % of 3rd harmonic content Zero adjustment: -5 to +5 % (front) Span adjustment: 95 to 105 % (front) INPUT SPECIFICATIONS Frequency: 40 Hz min., 1 kHz max. ■ AC Current: 0 – 1 A AC; input resistor incorporated Minimum span: 1 mA Input resistance Span 1 mA: 1 kΩ Span ≤ 2 mA: 500 Ω Span ≤ 5 mA: 200 Ω Span ≤ 10 mA: 100 Ω Span ≤ 20 mA: 50 Ω Span ≤ 50 mA: 20 Ω Span ≤ 100 mA: 10 Ω Span ≤ 500 mA: 1 Ω Span ≤ 1 A: 0.5 Ω ■ AC Voltage: 0 – 250 V AC Minimum span: 50 mV Input resistance: 200 kΩ min. INSTALLATION Current consumption: Approx. 35 mA Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 40 to 85 % RH (non-condensing) Mounting: Standard Rack 17BXE Weight: 150 g (0.33 lb)

MODEL: 17AC http://www.m-system.co.jp/ 17AC SPECIFICATIONS ES-2936 Rev.0 Page 2/3 PERFORMANCE in percentage of span Accuracy: ±0.4 % Temp. coefficient: ±0.02 %/°C (±0.01 %/°F) Response time: ≤ 0.5 sec. (0 – 90 %) Ripple: 0.5 %p-p max. Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 1500 V AC @ 1 minute (input to output or power)

500 V AC @ 1 minute (outut to power)

1500 V AC @ 1 minute (input or output or power to ground)

DIMENSIONS unit: mm (inch) 110 (4.33 ) 93 (3.66) 24 (.94) 7 (.28) 78 (3.07)32 (1.26) 8–M3.5 SCREW 7 (.28) 2–M3 SCREW TERMINAL ASSIGNMENTS 1 2 3 4 7 8 5 6

MODEL: 17AC http://www.m-system.co.jp/ 17AC SPECIFICATIONS ES-2936 Rev.0 Page 3/3 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM OUTPUTINPUT 1 AC Amplifier RMS Operation SZ * Input shunt resistor incorporated for current input Output Driver POWER CONNECTOR Isolation Specifications are subject to change without notice.