114-18388 TEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 18.02.2020 Rev.H AMP MCP 6.3/4.8K CONTACT SYSTEM AMP MCP 6.3/4.8K Kontaktsystem 1 of 11 © 2020 TE Connectivity family of companies All Rights Reserved | Indicates Change *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. Contents Page 1. SCOPE 2 2. REFERENCED DOCUMENTS 2
2.1 Customer drawings 2
2.2 Product specifications 2
2.3 Application specifications 2
2.4 Customer information 2
2.5 National / international standards 2
- DESCRIPTION 3
3.1 Contacts with insulation crimp 3
3.2 Contacts with crimp for single wire seal 4
- REQUIREMENTS 5
4.1 Cables 5
4.2 Cut off and burr 5
4.3 Conductor crimp 5
4.4 Insulation crimp / crimp for 5
4.5 Contact body 6
4.6 Shape and position tolerances of the 6
- CRIMPING DATA 8 Table 1: Contacts with insulation crimp 8 Table 2: Contacts with crimp for single wire seal 9 Table 3: Single wire seals 10 6. DEAD END PLUGS ASSEMBLY 10 7. AUXILIARY TOOLS 11
7.1 Extraction tool 11
7.2 Assembly tool 11
- ZWECK 2 2. ZUSÄTZLICHE UNTERLAGEN 2
2.1 Kundenzeichnungen 2
2.2 Produktspezifikationen 2
2.3 Verarbeitungsspezifikationen 2
2.4 Kundenbroschüren 2
2.5 Nationale / Internationale Normen 2
- BESCHREIBUNG 3
3.1 Kontakte mit Isolationscrimp 3
3.2 Kontakte mit Crimp für Einzelleiterdichtung 4
- ANFORDERUNGEN 5
4.1 Leitungen 5
4.2 Trennsteg und Grat 5
4.3 Drahtcrimp 5
4.4 Isolationscrimp / Crimp für 5
4.5 Kontaktkörper 6
4.6 Form- und Lagetoleranzen des 6
- CRIMPDATEN 8 Tabelle 1: Kontakte mit Isolationscrimp 8 Tabelle 2: Kontakte mit Crimp für Einzelleiterdichtung 9 Tabelle 3: Einzelleiterdichtungen 10 6. MONTAGE VON BLINDSTOPFEN 10 7. HILFSWERKZEUGE 11
7.1 Ausdrückwerkzeug 11
7.2 Montagehilfe 11
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 2 of 11 1. SCOPE 1. ZWECK This specification covers the special guidelines for the application of the AMP MCP6.3/4.8K contact system. Only specified TE crimp tools have to be used for application of contacts. Diese Spezifikation beinhaltet die Richtlinien zur Verarbeitung des AMP MCP6.3/4.8K Kontakt - systems. Es müssen die spezifizierten TE Crimpwerkzeuge zur Verarbeitung verwendet werden. 2. REFERENCED DOCUMENTS 2. ZUSÄTZLICHE UNTERLAGEN 2.1 Customer drawings 2.1 Kundenzeichnungen The customer drawing 1241438 shows the dimensions and materials for each part number. In the case of a conf lict between this document and the customer drawing, the customer drawing takes precedence. Die Kundenzeichnung 1241438 zeigt die Maße und Werkstoffe der Kontakte . Bei eventuell auftretenden Unterschieden zwischen d em vor - liegenden Dokument und der Kundenzeichnung sind die Daten, die in d er Kundenzeichnung enthalten sind, vorrangig maßgebend. 2.2 Product specifications 2.2 Produktspezifikationen The electrical and mechanical attributes of the contacts are defined in product specification 108-18718 for application with Tabs as far as 108-94427 for application with Type C Fuses (MEDIUM). In case of conflict, these take precedence over the general guidelines contained in this specification. Die elektrischen und mechanischen Eigen - schaften der Konta kte sind in den Produkt - spezifikationen 108-18718 für die Anwendung mit Flachsteckern, sowie in 108-94427 für Anwendung mit Typ C Sicherungen (MEDIUM) beschrieben. Diese haben im Zweifelsfall Vorrang vor den hier gemachten allgemeinen Angaben. 2.3 Application specifications 2.3 Verarbeitungsspezifikationen The g eneral guidelines laid down in application specifications 114-18022 and 114-18018 also apply to the crimp quality. Für die Crimpqualität gelten zusätzlich die allgemeinen Richtlinien nach Spezifikation 114-18022 und 114-18018. 2.4 Customer information 2.4 Kundenbroschüren 408-10389 describes the OCEAN side-feed crimping tool. 408-10389 beschreibt das OCEAN Side-feed Crimpwerkzeug. 2.5 National / international standards 2.5 Nationale / Internationale Normen LV112-1 2001-01 DIN 72 551 T5/02.93 Unscreened Low Tension Cables (FLR) DIN 72 551 T6/10.96 Unscreened Low Tension Cables (FLR) ISO 6722-3: 1993-02 Unscreened Low Tension Cables (FL) LV112-1 2001-01 DIN 72 551 T5/02.93 Ungeschirmte Niederspannungs- leitungen (FLR) DIN 72 551 T6/10.96 Ungeschirmte Niederspannungs - leitungen (FLR) ISO 6722-3: 1993-02 Ungeschirmte Niederspannungs- leitungen (FL)
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 4 of 11
3.2 Contacts with crimp for single wire seal
3.2 Kontakte mit Crimp für
Uncrimped contact / ungecrimpter Kontakt Figure 4 / Bild 4
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 5 of 11 4. REQUIREMENTS 4. ANFORDERUNGEN 4.1 Cables 4.1 Leitung Only FLR conductors acc. DIN 72551 part 5 and 6 or LV112 -1 as well as FL conductors acc. ISO 6722-3 may be used in accordance with the data out of table 1 and 2. Other conductor s require the approval of the TE engineering department. Single termination is preferred. Double te rmination within the conductor range is possible only with restrictions. Es dürfen nur FLR Leitungen nach DIN 72551 Teil 5 und 6 bzw. LV112 -1 sowie FL Leitungen nach ISO 6722 -3 nach Angabe aus Tabelle 1 und 2 verwendet werden. Andere Leitungen benötigen die Freigabe der TE Entwicklungsabteilung. Die Leitungen selbst werden vorzugsweise als Einzelanschläge verarbeitet. Doppelanschläge sind innerhalb des D rahtgrößenbereichs nur bedingt möglich. The cable must be stripped to the lengths shown in tables 1 and 2. Take care that the individual strands of the conductor are not be bent or cut off. For single wire seal, take care that the insulation of the c able in the sealing area is not damaged, compressed or deformed. The insulation must be clean and free of contamination. Die Leitung wird nach den Längenangaben in Tabelle 1 und 2 abisoliert. Einzeldrähte dürfen dabei weder beschädigt noch aufgespleißt od er abgeschnitten werden. Bei Verarbeitung mit Einzeldichtungen darf die Isolation im Dicht - bereich nicht beschädigt oder verformt sein. Die Oberfläche mu ss frei von Verunreinigungen und Rückständen sein.
4.2 Cut off and burr
4.2 Trennsteg und Grat
The data acc. figure 2 and 4 are valid. Es gelten die Angaben nach Bild 2 und 4.
4.3 Conductor crimp
4.3 Drahtcrimp
The conductor position data acc. figure 2 and 4 are valid. Für die Lage der Leiter gelten die Angaben nach Bild 2 und 4. In no case may the end of the insulation be crimped in the conductor crimp. Das Isolationsende darf keinesfalls im Drahtcrimp eingecrimpt werden. The shape, height and width of the crimp and the conductor range is shown in tables 1 and 2. The crimp width is determined by the crimping tool and is defined as the distance between the tangent points of the two rolling radii with the vertical. The data is only a check dimension to check whether the correct tool is used. It is no quality measurin g criterion. Die Crimpform, -höhe und -breite sowie Leiter - querschnitte sind in Tabelle 1 und 2 aufgeführt. Die Crimpbreite ist ein werkzeuggebundenes Maß und als Abstand der Tangentenpunkte beider Einrollradien zu den Senkrechten definiert. Die Angabe ist nur ein Prüfmaß, ob das richtige Crimp- werkzeug verwendet wird. Sie ist kein Qualitäts - messkriterium. 4.4 Insulation crimp / crimp for single wire seal 4.4 Isolationscrimp / Crimp für Einzelleiterdichtung The shape and width of the crimp and the insulation diameter are shown in t ables 1 and 2. Due to the large tolerances of the insulation diameters, no crimp height is specified. The position of the isolation end for contacts with insulation crimp are defined in spec. 114-18022. For single wire seal data defined in spec 114 - 18018 but with partly different dimensions acc. figure 4 are valid. Die Crimpform und die Crimpbreite sowie die Isolationsdurchmesser sind in Tabelle 1 und 2 aufgeführt. Eine Isolationscrimphöhe wird wegen der großen Toleranzen des Isolationsdurch - messers nicht vorgegeben. Die Lage des Isolationsendes für Kontakte mit Isolationscrimp ist in der Spez. 114 -18022 definiert. Für Einzelleiterdichtungen gelten die Angaben nach Spez. 114 -18018, jedoch mit teils abweichenden Maßen, welche in Bild 4 definiert sind.
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 6 of 11 Qualified single wire seals are defined in table 3. For position of single wire seals data acc. figure 4 are valid. Die freigegebenen Einzelleiterdichtungen sind in Tabelle 3 definiert. Für die Position der Einzel leiterdichtungen gelten die Angaben nach Bild 4. 4.5 Contact body 4.5 Kontaktkörper Contact body, cantilever spring, locking lances as well as the transit ion of the crimp barrel to the contact body may neither be bent nor deformed during the crimping process. Kontaktkörper, Überfeder, Rastfeder sowie der Übergang der Crimphülse zum Kontaktkörper dürfen durch den Crimpvorgang weder verbogen noch deformiert werden.
4.6 Shape and position tolerances of the
4.6 Form- und Lagetoleranzen des gecrimpten
A. Contacts with Insulation crimp A. Kontakte mit Isolationscrimp Referring to the symmetry of the crimp the details acc. to figure 5 are valid. Bezüglich der Symmetrie des Crimps gelten die Angaben nach Bild 5. Figure 5 / Bild 5
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 7 of 11 B. Contacts with crimp for single wire seals B. Kontakte mit Crimp für Einzelleiter- dichtungen Referring to the symmetry of the crimp the details acc. to figure 6 are valid. Bezüglich der Symmetrie des Crimps gelten die Angaben nach Bild 6. Figure 6 / Bild 6
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 8 of 11 5. CRIMPING DATA 5. CRIMPDATEN Table 1: Contacts with insulation crimp Tabelle 1: Kontakte mit Isolationscrimp 1) Current standard / aktueller Standard 2) Preferred standard to meet new requirement @ LV214-2 Slow motion bending test / Bevorzugter Standard um den neuen Anforderungen der LV214-2 Slow Motion Prüfung zu genügen 3) PN 1241400 superseded by PN 5-1241400 / PN 1241400 nicht für Neuanwendungen, wird ersetzt durch PN 5-1241400 Figure 7 / Bild 7
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 9 of 11 Table 2: Contacts with crimp for single wire seal Tabelle 2: Kontakte mit Crimp für Einzelleiterdichtung 1) Current standard / aktueller Standard 2) Preferred standard to meet new requirement @ LV214-2 Slow motion bending test / Bevorzugter Standard um den neuen Anforderungen der LV214-2 Slow Motion Prüfung zu genügen 3) PN 1241410 superseded by PN 5-1241410 / PN 1241410 nicht für Neuanwendungen, wird ersetzt durch PN 5-1241410 Figure 8 / Bild 8
Verarbeitungsspezifikation AMP MCP6.3/4.8K 114-18388 Rev. H 10 of 11 Table 3: Single wire seals Tabelle 3: Einzelleiterdichtungen SINGLE WIRE SEALS / Einzelleiterdichtungen Bestell-Nr. / ORDER NO Isolations – Ø / INSULATION - Ø Farbe / COLOUR 2177018-1 1,2–2,0 Gelb / YELLOW 1394511-1 2,0–2.7 Weiss / WHITE 1823111-1 2,7–3,0 Rotbraun / REDBROWN 1394512-1 3,4–3,7 Blau / BLUE 1719043-1 4,0-4,5 Gruen / GREEN 6. Dead end plugs assembly 6. Montage von Blindstopfen Dead end plugs are available to seal cavities which are not occupied by contacts. The dead end plug is positioned in the contact cavity as shown in figure 9: Zur Abdichtung von Kontaktkammern , welche nicht mit Kontakten belegt sind, stehen Blindstopfen zur Verfügung. Die Position der Blindstopfen in der Kontaktkammer wird in Bild 9 gezeigt: Order-No.: 967652-1 Bestell Nr.: 967652-1 Figure 9 / Bild 9