167 CDE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Type 167/184 Metallized Polyester Radial Lead Capacitors CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Specifications Radial Box Metallized Polyester Capacitors for Automatic Insertion Highlights

  • Rugged plastic case
  • Case and epoxy fill meets UL94V0
  • 7.5 mm (0.3”) lead spacing
  • Bulk, tape and reel or ammo pack
  • Non-inductively wound
  • Non-polar Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): 0.001 µF to 1.0 µF

63 Vdc to 630 Vdc

±5%, ±10%, ±20% –55 ºC to +125 ºC (with 50% Vdc derating >85 ºC) 1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC tanδ x 10 –4 at 25 ºC ±5 ºC The Type 167/184 series radial lead metallized polyes- ter box capacitors are available in bulk (Type 167) or on ammo pack or radial tape and reel (Type 184). These capacitors are constructed in rugged rectangular plas- tic cases and all come with 7.5 mm (0.3”) lead spacing. They are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppression. Total Self Inductance (L): Maximum Pulse Rise Time (dv/dt): If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V. Approximately 8 nH kHz tanδ x 10–4 1 ≤100 10 ≤150 Vn V/µs 63 12 100 20 250 32 400 41 630 70 RoHS Compliant Long Term Stability (after two years) Storage Standard Environmental Conditions Performance Capacitance Change ∆C/C ≤ ±3%

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors L Max T Max H Max S ±.015 (±0.4 mm) .217 ±.039 (5.5 ±1.0 mm) Capacitor Outline Drawing Ratings Test Method and Performance * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications) Insulation Resistance Test Conditions Temperature 25 ºC ±5 ºC Voltage Charge Time 1 minute Voltage Charge 50 Vdc for Vn < 100 Vdc

100 Vdc for Vn ≥ 100 Vdc

For Vn > 100 Vdc ≥30,000 MΩ (50,000 MΩ typical) For Vn ≤100 Vdc ≥10,000 MΩ for C ≤ 0.1µF ≥1,000 MΩ x µF for > 0.1µF Damp Heat Test Test Conditions Temperature +40 ºC Relative Humidity 95% Test Duration 21 days Performance Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤50 x 10 4 at 1 kHz Insulation Resistance ≥ 50% of limit value Life Test Test Conditions Temperature +85 ºC Test Duration 1000 hrs Voltage Applied 1.25 x Vn Performance Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz Insulation Resistance ≥ 50% of limit value Lead length shown is as supplied on 167 Series Soldering Test Conditions Soldering Temperature 260 ºC ±5 ºC Soldering Duration 10 sec ±1 sec Performance Capacitance Change ∆C/C ≤ ±2% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz Insulation Resistance ≥ limit value Cap (µF) Catalog Part Number Tape & Reel Ammo Pack Inches Millimeters L T H S Ød L T H S Ød

63 Vdc

100 Vdc

Ød ±.003 (±0.076)

Type 167/184 Metallized Polyester Radial Lead Capacitors CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification) Part Numbering System for Bulk Items 167 104 K 100 A -F Case RoHS Series Capacitance Tolerance Voltage Code Compliant 167 392 = .0039 µF J = ±5% 63 = 63 Vdc A Designator 103 = .01 µF K = ±10% 100 = 100 Vdc B 104 = .1 µF M = ±20% 250 = 250 Vdc C 105 = 1.0 µF 630 = 630 Vdc D Cap (µF) Catalog Part Number Tape & Reel Ammo Pack Inches Millimeters L T H S Ød L T H S Ød (µF) Catalog Part Number Tape & Reel Ammo Pack Inches Millimeters L T H S Ød L T H S Ød

250 Vdc

400 Vdc

630 Vdc

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Tape Specification - 7.5 mm Lead Spacing > The H dimension depends on the insertion equipment used. Specify the proper tooling code as indicated below. Part Numbering System for Auto Insertion * Tooling code (>) depends on the users insertion equipment requirements. See table for available options. 280 mm Max 11.02” 335 mm Max 13.19” 47 mm Max 1.85” Ammo Box Packing Reel Packing 30 mm 1.18” 331 mm 13.04” ΔH PoP Do Ød W H Wo Item Code Millimeters Inches Feed Hole Pitch P0 2.7±0.3 .5±.012 Pitch of Component P1 12.7±1.0 .5±.039 Hole Center to Lead P2 3.75±0.7 .148±.028 Component Alignment, F-R ∆h 0±2.0 0±.079 Hold-down Tape Width W0 6.0 min .236 min Hold-down Tape Position W2 3.0 Max .118 Max Height of Component H > > from Tape Center Feed Hole Diameter D0 4.0±0.3 .157±.012 Case Quantity Quantity Code Reeled Ammo Pack A 1800 1500 B 1500 1500 C 1200 1000 D 1000 1000 Tooling H Dimensions Code Millimeters Inches C 16.0±0.75 .630±030 184 104 K 100 R A B -F Packaging *Tooling RoHS Type Case Code Compliant Series Capacitance Tolerance Voltage (#) Code (>) Designator 184 392 = .0039 µF J = ±5% 63 = 63 Vdc A = Ammo A A 103 = .01 µF K = ±10% 100 = 100 Vdc R = Tape & Reel B B 104 = .1 µF M = ±20% 250 = 250 Vdc C C 105 = 1.0 µF 630 = 630 Vdc D * Tooling code is at the discretion of the user depending on the insertion equipment being used. See table for specific "H" dimensions

Type 167/184 Metallized Polyester Radial Lead Capacitors CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information con- tained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guaran- tee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representa- tion regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indi- cated in such warnings, cautions and notes, or that other safety measures may not be required.