DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

356198- -1 (Ref) CHAMP .050 Series I Blindmate Press- -Fit Vertical Receptacle Connector (Ref) PC Board Support Fixture (Ref) Compliant Pin Contact (Board Retention Feature) PC (Printed Circuit) Board (Ref) Instruction SheetSeating Tool Assemblies 1320142- [ ] and 356198- [ ] For CHAMP* .050 Series I Blindmate Press- Fit 408- -4328 LOC B 1 of 4E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1-- 800-- 722-- 1111 PRODUCT INFORMATION 1- -800- -522- -6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website atwww.te.com

28 APR 11 Rev CConnectors with Compliant Pin Contacts

NO. OF CONNECTOR ROWS CONNECTOR TYPE 1320142- -1 40 Extended Height 1320142- -2 80 Height Press- -Fit 356198- -1 80 356198- -2 40 Press- -Fit 356198- -3 20 Figure 1 1. INTRODUCTION Seating Tool Assemblies 1320142- -[ ] and 356198- -[ ] are designed to seat CHAMP .050 Series I Blindmate press- -fit and extended height press- -fit vertical receptacle connectors. The connectors contain compliant pin contacts to allow solderless pc board installation. Each seating tool is specifically designed for the number of rows in a connector. See Figure 1. Read these instructions and understand them before using the seating tool. Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures are not drawn to scale. Reasons for reissue are provided in Section 7, REVISION SUMMARY. 2. DESCRIPTION During seating, the seating tool covers the connector and presses on the top surface of the connector when the applicator ram applies force to the seating tool. The pc board is positioned onto a pc board support fixture for support. 3. REQUIREMENTS 3.1. PC Board Support Fixture(Customer Supplied) A pc board support must be used to provide proper support for the pc board and alignment of the seating tool to the contacts, and to protect the pc board and and connector from damage. The board support fixture must be designed for specific needs using the recommendations in Instruction Sheet 408- -6927. NOTE i

  1. MAINTENANCE AND INSPECTION The seating tool is assembled and inspected before shipment. TE Connectivity recommends that the tool be inspected immediately upon arrival at your facility to ensure that the tool has not been damaged during shipment, and that the tool conforms to the dimensions provided in Figure 3. 5.1. Daily Maintenance TE recommends that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint- -free cloth. Do NOT use objects that could damage the tool components. 2. When the tool is not in use, store it in a clean, dry area. 5.2. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the tooling or be supplied to supervisory personnel responsible for the tool. Inspection frequency should be based on amount of use, working conditions, operator training and skill, and established standards. 6. REPLACEMENT AND REPAIR Refer to Figure 3 for customer- -replaceable parts. A complete inventory should be stocked to prevent production downtime when replacement of parts is necessary. Order replacement parts through your TE representative, or call 1- -800- -526- -5142, or send a facsimile of your purchase order to 717- -986- -7605, or write to: CUSTOMER SERVICE (038- -035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105- -3608 For customer repair service, please contact a TE representative at 1- -800- -526- -5136. Dim. A 38.1 mm [1.50 in.] 38.02 mm [1.497 in.] DIMENSION A (Length mm [in.]) FOR SEATING TOOL 1320142- -1 1320142- -2 REPLACEMENT PARTS ITEM PART NUMBER FOR ASSEMBLY DESCRIPTION QTY PERITEM 1320142- -1 1320142- -2 DESCRIPTION QTY PER ASSEMBLY 1- -21002- -3 — SCREW, Button Head Cap 4- -40 2 1 — 1- -21002- -3 SCREW, Button Head Cap 4- -40 4 2 1320143- -1 1320143- -2 BLADE, Insertion 2 2- -21012- -8 — SCREW, Socket Set 6- -32 5 3 — 2- -21012- -8 SCREW, Socket Set 6- -32 10 4 354698- -2 354699- -1 ADAPTER 1 Figure 3 (cont’d)

Dim. A 5 3 38.1 mm [1.50 in.] 38.02 mm [1.497 in.] DIMENSION A (Length mm [in.]) FOR SEATING TOOL 356198- -1 356198- -2 356198- -3 REPLACEMENT PARTS ITEM PART NUMBER FOR ASSEMBLY DESCRIPTION QTY PERITEM 356198- -1 356198- -2 356198- -3 DESCRIPTION QTY PER ASSEMBLY 1 356195- -1 356195- -2 356195- -3 BAR, Push 1 2 1214044- -1 1214044- -1 1214044- -1 PLATE, End 2 3 1- -21002- -7 1- -21002- -7 1- -21002- -7 SCREW, Button Head Cap 6- -32 4 4 1214041- -1 1214041- -2 1214041- -2 PLATE, Stabilizer 1 2- -21002- -1 2- -21002- -1 — SCREW, Button Head Cap 8- -32 2 — — 2- -21002- -1 SCREW, Button Head Cap 8- -32 1 6 356194- -1 356194- -2 356194- -3 PLATE, Side 2 2- -21000- -9 2- -21000- -9 — SCREW, Socket Head Cap 8- -32 2 — — 2- -21000- -9 SCREW, Socket Head Cap 8- -32 1 21018- -6 21018- -6 — NUT , Hex 8- -32 1 — — 21018- -6 NUT , Hex 8- -32 2 Figure 3 (end) 7. REVISION SUMMARY Since the previous version of this document, the following changes were made: S Updated document to corporate requirements.