10VPN MSYSTEM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
MODEL: 10VPN http://www.m-system.co.jp/ 10VPN SPECIFICATIONS ES-0830 Rev.13 Page 1/3 High-density Signal Conditioners 10-RACK LOOP POWERED I/P TRANSDUCER Functions & Features
- Converting a DC input into a proportional standard pneumatic signal
- Loop powered
- Semiconductor pressure sensor in the feedback circuit
- High resolution
- No mounting position effect Typical Applications
- Converting a 4 – 20 mA from a PID controller into a pneumatic signal MODEL: 10VPN–[1]A[2]0[3]
ORDERING INFORMATION
- Code number: 10VPN-[1]A[2]0[3] Specify a code from below for each [1] through [3]. (e.g. 10VPN-2A2S0/Q)
- Specify the specification for option code /Q (e.g. /C01) [1] PNEUMATIC CONNECTION 2: Rc 1/4" 5: Rc 1/8" fitting 7: 1/4" NPT fitting INPUT Current A: 4 – 20 mA DC [2] OUTPUT 1S: 19.6 – 98.1 kPa 2S: 20 – 100 kPa 3S: 20.7 – 103.4 kPa 1: 0.2 – 1.0 kgf/cm2 2: 0.2 – 1.0 bar 3: 3 – 15 psig [3] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating
RELATED PRODUCTS
- Standard rack with air manifold The 10VPN must be installed in a 10-Rack series rack with air manifold. GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals at the front and via card-edge connector at the rear Connection Input: M3.5 screw terminals (torque 0.8 N·m) and card- edge connector Pneumatic: Rc 1/4", Rc 1/8" or 1/4" NPT female (torque ≤ 12 N·m) Material Housing: Flame-resistant resin (black) Base: Die cast aluminium Screw terminals: Nickel-plated steel Zero adjustment: -5 to +5 % (front) Span adjustment: 95 to 105 % (front) INPUT SPECIFICATIONS Equivalent input impedance: Approx. 310 Ω at 20 mA The voltage measure at the input terminals changes corresponding to the input signal as in the diagram below. Be sure that the device at the input side allows the load increase. INPUT CURRENT [mA] 4 12 20 approx. 6.2 approx. 5.7 VOLTAGE [V] ACROSS INPUT TERMINALS 5.8 6.0
MODEL: 10VPN http://www.m-system.co.jp/ 10VPN SPECIFICATIONS ES-0830 Rev.13 Page 2/3 OUTPUT SPECIFICATIONS ■ Output: 19.6 – 98.1 kPa, 0.2 – 1.0 kgf/cm2 20 – 100 kPa, 0.2 – 1.0 bar 20.7 – 103.4 kPa, 3 – 15 psig The output goes below 0 % if the input loop is open. Maximum air delivery: 60 Nl/minute (2.1 SCFM) Maximum air exhaust: 60 Nl/minute (2.1 SCFM) INSTALLATION Supply pressure: 140 kPa (1.4 kgf/cm2, 1.4 bar, 20 psig) ±10 %. Use dry air containing no carbon black or other foreign particles. To ensure reliability use an air filter (0.01 microns). Air consumption: 6 Nl/minute (0.21 SCFM) Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Standard Rack 10BXx Weight: 300 g (0.66 lb) PERFORMANCE in percentage of span Accuracy: ±0.3 % including linearity and repeatability Linearity: ±0.2 % Repeatability: 0.1 % Temp. coefficient: ±0.05 %/°C (±0.03 %/°F) Response time: ≤ 3 sec. (0 – 90 %) Mounting position effect: ±0.1 % (all dimensions) EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 91 (3.58) 99 (3.90 ) 3 (.12) 32 (1.26) 2–4.3 (.17) dia. MTG HOLE 20 (.79) approx. 27 (1.06) * [13 (.51)] OUTPUT CONNECTION Rc 1/4”, Rc 1/8”, 1/4” NPT FITTING 7 8 5 6 4–M3.5 SCREW Fitting provided for Rc 1/8" or 1/4" NPT connection. 82 (3.23) 25 (.98)
MODEL: 10VPN http://www.m-system.co.jp/ 10VPN SPECIFICATIONS ES-0830 Rev.13 Page 3/3 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Pilot Valve Z S SUPPLY PRESSURE Semiconductor Pressure Sensor Deviation Amplifier+ INPUT DriverPower Supply OUTPUT CONNECTOR INPUT ELECTRO-MAGNETIC FLAPPER When the input signal is provided from the card-edge connector, the front terminals are not available for use. mA MONITOR (4 – 20mA DC) Specifications are subject to change without notice.