10VF-H60-R

10VF MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

MODEL: 10VF http://www.m-system.co.jp/ 10VF SPECIFICATIONS ES-0817 Rev.11 Page 1/3 High-density Signal Conditioners 10-RACK SIGNAL TRANSMITTER (high speed response) Functions & Features

• Converts DC input from a sensor into a standard process signal
• Isolation between input and output
• 180-microsecond response MODEL: 10VF–[1][2]0–R[3]

ORDERING INFORMATION

• Code number: 10VF-[1][2]0-R[3] Specify a code from below for each [1] through [3]. (e.g. 10VF-6A0-R/Q)
• Special input range (For codes 0)
• Specify the specification for option code /Q (e.g. /C01) [1] INPUT Current A: 4 – 20 mA DC (Input resistance 250 Ω) D: 0 – 20 mA DC (Input resistance 50 Ω) G: 0 – 1 mA DC (Input resistance 1000 Ω) H: 10 – 50 mA DC (Input resistance 100 Ω) Voltage 3: 0 – 1 V DC (Input resistance 1 MΩ min.) 4: 0 – 10 V DC (Input resistance 1 MΩ min.) 5: 0 – 5 V DC (Input resistance 1 MΩ min.) 6: 1 – 5 V DC (Input resistance 1 MΩ min.) 4W: -10 – +10 V DC (Input resistance 1 MΩ min.) 0: Specify voltage (See INPUT SPECIFICATIONS) [2] OUTPUT 1 Current A: 4 – 20 mA DC (Load resistance 600 Ω max.) D: 0 – 20 mA DC (Load resistance 600 Ω max.) G: 0 – 1 mA DC (Load resistance 12 kΩ max.) Voltage 3: 0 – 1 V DC (Load resistance 1000 Ω min.) 4: 0 – 10 V DC (Load resistance 10 kΩ min.) 5: 0 – 5 V DC (Load resistance 5000 Ω min.) 6: 1 – 5 V DC (Load resistance 5000 Ω min.) 4W: -10 – +10 V DC (Load resistance 10 kΩ min.) OUTPUT 2 0: None POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [3] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals at the front and via card-edge connector at the rear; terminal cover provided Connection Input: M3.5 screw terminals (torque 0.8 N·m) Output: Card-edge connector and M3.5 screw terminals (torque 0.8 N·m) Power input: Supplied from card-edge connector Screw terminal: Nickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Input to output to power Overrange output: Approx. -10 to +120 % at 1 – 5 V Zero adjustment: -5 to +5 %; multi-turn screwdriver adjustments (front) Span adjustment: 95 to 105 %; multi-turn screwdriver adjustments (front) INPUT SPECIFICATIONS ■ DC Current: Input resistor incorporated ■ DC Voltage: -300 – +300 V DC Minimum span: 1 V Offset: Max. 1.5 times span

MODEL: 10VF http://www.m-system.co.jp/ 10VF SPECIFICATIONS ES-0817 Rev.11 Page 2/3 Input resistance: ≥ 1 MΩ OUTPUT SPECIFICATIONS With the input voltage code 3, 4, 5, 6 and current, the output goes below 0 % when the input is open. INSTALLATION Current consumption: Approx. 35 mA for voltage output Approx. 65 mA for current output Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Standard Rack 10BXx Weight: 180 g (0.40 lb) PERFORMANCE in percentage of span Accuracy: ±0.1 % Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: Approx. 180 μsec. (0 – 90 %) Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (input to output to power)

1500 V AC @ 1 minute (input or output or power to ground)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 130 (5.12) 3 (.12) 51 (2.01) 82 (3.23) 2–4.3 (.17) dia. MTG HOLE TERMINAL COVER 7–M3.5 SCREW 8 (.31) 91 (3.58) 99 (3.90 ) 25 (.98) 1 2 5 6 7 8

MODEL: 10VF http://www.m-system.co.jp/ 10VF SPECIFICATIONS ES-0817 Rev.11 Page 3/3 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation Low Drift Amplifier Output Driver OUTPUT 6CONNECTOR SZ OUTPUT POWER *Input shunt resistor incorporated for current input. Remark: This module, due to its fast-response design, does not eliminate noises included in the input signal. Use shielded twisted-pair cable for preventing them. SIGNAL SOURCE Specifications are subject to change without notice.