10SP-1D6-R

10SP MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

MODEL: 10SP http://www.m-system.co.jp/ 10SP SPECIFICATIONS ES-0856 Rev.8 Page 1/3 High-density Signal Conditioners 10-RACK LOW FREQUENCY TRANSMITTER (50 Hz minimum) Functions & Features

• Converting the output from a pulse-type transducer into a standard process signal
• Excitation
• Optional second channel output available at the front terminals and at the Standard Rack connector Typical Applications
• Positive displacement flowmeters, turbine flowmeters and vortex flowmeters
• Proximity switches MODEL: 10SP–[1][2][3]–R[4]

ORDERING INFORMATION

• Code number: 10SP-[1][2][3]-R[4] Specify a code from below for each [1] through [4]. (e.g. 10SP-2A6-R/Q)
• Frequency range (e.g. 0 – 10 kHz)
• Specify the specification for option code /Q (e.g. /C01) [1] INPUT 1: Dry contact 2: Voltage pulse [2] OUTPUT 1 Current A: 4 – 20 mA DC (Load resistance 600 Ω max.) B: 2 – 10 mA DC (Load resistance 1200 Ω max.) C: 1 – 5 mA DC (Load resistance 2400 Ω max.) D: 0 – 20 mA DC (Load resistance 600 Ω max.) E: 0 – 16 mA DC (Load resistance 750 Ω max.) F: 0 – 10 mA DC (Load resistance 1200 Ω max.) G: 0 – 1 mA DC (Load resistance 12 kΩ max.) Voltage 1: 0 – 10 mV DC (Load resistance 10 kΩ min.) 2: 0 – 100 mV DC (Load resistance 100 kΩ min.) 3: 0 – 1 V DC (Load resistance 100 Ω min.) 4: 0 – 10 V DC (Load resistance 1000 Ω min.) 5: 0 – 5 V DC (Load resistance 500 Ω min.) 6: 1 – 5 V DC (Load resistance 500 Ω min.) [3] OUTPUT 2 0: None Voltage 6: 1 – 5 V DC (Load resistance 5000 Ω min.) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [4] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals at the front and via card-edge connector at the rear; terminal cover provided Connection Input: M3.5 screw terminals (torque 0.8 N·m) Output: Card-edge connector and M3.5 screw terminals (torque 0.8 N·m) Power input: Supplied from card-edge connector Screw terminal: Nickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Input to output 1 to output 2 to power Overrange output: Approx. 0 to 120 % at 1 – 5V Zero adjustment: -5 to +5 % (front) Span adjustment: 95 to 105 % (front) Input pulse sensing: DC coupled; detecting pulse rise Low-end cutout: 2 to 5 %

MODEL: 10SP http://www.m-system.co.jp/ 10SP SPECIFICATIONS ES-0856 Rev.8 Page 2/3 INPUT SPECIFICATIONS Excitation: 12 V DC @30 mA; shortcircuit protection Frequency range: 0 – 50 Hz through 10 kHz ■ Dry Contact: Mechanical contact or open collector Pulse width time requirement: 20 μsec. min. for ON and OFF Sensing: Approx. 12 V DC @3 mA ON/OFF level: ≤ 200 Ω / 0.6 V for ON, ≥ 100 kΩ / 6 V for OFF ■ Voltage Pulse: Square or sine waveforms Pulse width time requirement: 20 μsec. min. for high and low levels Hi level: 2 – 50 V Lo level: ≤ 1 V Input impedance: 10 kΩ min. INSTALLATION Current consumption: Approx. 25 mA with voltage output 1 Approx. 45 mA with current output 1 Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Standard Rack 10BXx Weight: 200 g (0.44 lb) PERFORMANCE in percentage of span Accuracy: ±0.1 % (output 10 – 100 %) Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: (0 – 90%) Approx. 1.8 sec. with 0 – 50 Hz Approx. 0.7 sec. with 0 – 100 Hz Approx. 0.5 sec. with 0 – 500 Hz Approx. 0.5 sec. with 0 – 10 kHz Ripple: 0.2 %p-p max. with input ≥ 10 % Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (input to output 1 to output 2 to power)

1500 V AC @ 1 minute (input or output or power to ground)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 130 (5.12) 3 (.12) 51 (2.01) 82 (3.23) 2–4.3 (.17) dia. MTG HOLE TERMINAL COVER 7–M3.5 SCREW 8 (.31) 91 (3.58) 99 (3.90 ) 25 (.98) 1 2 5 6 7 8

MODEL: 10SP http://www.m-system.co.jp/ 10SP SPECIFICATIONS ES-0856 Rev.8 Page 3/3 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation Waveform Shaper Output Driver OUTPUT 1 12V Supply INPUT SENSOR EXCITATION Smoother * 4k Ω attached for dry contact input only. 1 output type has the output 1 connected to the card-edge connector in parallel. Remark 1) The section enclosed by broken line is only for 2nd output channel. Isolation Output Driver OUTPUT 2 6CONNECTOR OUTPUT 2 POWER SZ One-Shot SZ Specifications are subject to change without notice.