10MS

10MS MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

MODEL: 10MS http://www.m-system.co.jp/ 10MS SPECIFICATIONS ES-0816 Rev.6 Page 1/2 High-density Signal Conditioners 10-RACK POTENTIOMETER TRANSMITTER Functions & Features

• Providing two DC outputs proportional to a potentiometer or slidewire position input
• 50 % zero/span adjustments with minimal interaction
• Optional second channel output available at the front terminals and at the Standard Rack connector Typical Applications
• Tank levels
• Positions MODEL: 10MS–[1][2]–R[3]

ORDERING INFORMATION

• Code number: 10MS-[1][2]-R[3] Specify a code from below for each [1] through [3]. (e.g. 10MS-A6-R/Q)
• Specify the specification for option code /Q (e.g. /C01) INPUT POTENTIOMETER Total resistance 100 Ω – 10 kΩ [1] OUTPUT 1 Current A: 4 – 20 mA DC (Load resistance 600 Ω max.) B: 2 – 10 mA DC (Load resistance 1200 Ω max.) C: 1 – 5 mA DC (Load resistance 2400 Ω max.) D: 0 – 20 mA DC (Load resistance 600 Ω max.) E: 0 – 16 mA DC (Load resistance 750 Ω max.) F: 0 – 10 mA DC (Load resistance 1200 Ω max.) G: 0 – 1 mA DC (Load resistance 12 kΩ max.) Voltage 1: 0 – 10 mV DC (Load resistance 10 kΩ min.) 2: 0 – 100 mV DC (Load resistance 100 kΩ min.) 3: 0 – 1 V DC (Load resistance 100 Ω min.) 4: 0 – 10 V DC (Load resistance 1000 Ω min.) 5: 0 – 5 V DC (Load resistance 500 Ω min.) 6: 1 – 5 V DC (Load resistance 500 Ω min.) [2] OUTPUT 2 0: None Voltage 6: 1 – 5 V DC (Load resistance 5000 Ω min.) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [3] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals at the front and via card-edge connector at the rear; terminal cover provided Connection Input: M3.5 screw terminals (torque 0.8 N·m) Output: Card-edge connector and M3.5 screw terminals (torque 0.8 N·m) Power input: Supplied from card-edge connector Screw terminal: Nickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Input to output 1 to output 2 to power Overrange output: Approx. -10 to +120 % at 1 – 5 V Zero adjustment: 0 – 50 % of total resistance (front) Span adjustment: 50 – 100 % of total resistance (front) INPUT SPECIFICATIONS Minimum span: 50 % of total resistance Excitation: Approx. 0.2 V DC INSTALLATION Current consumption: Approx. 35 mA with voltage output 1 Approx. 55 mA with current output 1 Operating temperature: -5 to +55°C (23 to 131°F)

MODEL: 10MS http://www.m-system.co.jp/ 10MS SPECIFICATIONS ES-0816 Rev.6 Page 2/2 Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Standard Rack 10BXx Weight: 200 g (0.44 lb) PERFORMANCE in percentage of span Accuracy: ±0.1 % Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: ≤ 0.5 sec. (0 – 90 %) Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (input to output 1 to output 2 to power)

1500 V AC @ 1 minute (input or output or power to ground)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 130 (5.12) 3 (.12) 51 (2.01) 82 (3.23) 2–4.3 (.17) dia. MTG HOLE TERMINAL COVER 7–M3.5 SCREW 8 (.31) 91 (3.58) 99 (3.90 ) 25 (.98) 1 2 5 6 7 8 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Isolation Output Driver OUTPUT 1 SZ Output Driver OUTPUT 2 6CONNECTOR *1 output type has the output 1 connected to the card-edge connector in parallel. Remark 1) The section enclosed by broken line is only for 2nd output channel. OUTPUT 2* POWER SZ Voltage/ Duty Cycle Low Drift Amplifier POTENTIOMETER max. min. Excitation Circuit Specifications are subject to change without notice.