9E103G DUBILIER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 135 RESISTORS RESISTOR NETWORK SIL No of Pins 5 6 7 8 9 10 11 12 13
ORDERING INFORMATION
RANGE & TOLERANCES OUTLINE DRAWING Low-profile Epoxy dipped 5 to 13-pin The Dubilier range of SIL networks features 2% accuracy in a low- cost package. The low-profile epoxy package allows the device to be used in locations where moulded parts do not fit. Isolated and common-terminal designs are available, allowing the simple, reliable insertion of up to 12 resistors at once. Parameter Performance Limits Power Rating per Element 0.125W @ 70°C Temperature Range -55˚ to +125°C Derating linearly from 70°C Resistance Range 33Ω to 1MΩ E - 24 series Resistance Tolerance ± 2% (G) Temperature Coefficient ± 100 ppm/°C 50Ω ≥ 2.2MΩ ± 250ppm/˚C <50Ω – 2.2MΩ Max Working Voltage 100V Max Overload Voltage 200V L max 0.5 ± 0.1 2.54 ± 0.25 9E-103GPIN 1 Marking 2.5 max 5.2 max 3.0 ± 0.5 3.0 ± 0.1
9 E 103 G
N° Pins 5 to 13 Type M = Isolated E = Common Value 3 digit code : Last digit is decade multiplier. First two digits are first digits of value. Tolerance SECTION 4
Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 136 SPECIFICATION RESISTORS RESISTOR NETWORK SIL SIL PIN-OUTS Short Term Overload ∆R/R ± (1% + 0.05Ω) After application of 21/2 x rated voltage, or the maximum overload voltage, whichever smaller, for a period of 5 secs. Resistance change to be within specification, with no evidence of arcing, burning or charring. Vibration ∆R/R ± (0.5% + 0.5Ω) Resistors are to be subjected to vibration of amplitude 0.8mm for 2 hours in each of three mutually perpendicular directions. The vibration frequency shall be swept from 10 to 55 to 10Hz in 1 minute. Resistance change to be within specification with no evidence of damage. Dielectric Strength Components shall withstand twice their rated voltage for 1 minute applied between termination and substrate. No evidence of arcing, burning or charring. Solderability ∆R/R ± (1% + 0.05Ω) After dipping at 260°C ± 5°C for 10 seconds, resistance change to be within specification, with no evidence of arcing, burning or charring. Terminations shall maintain a minimum of 75% coverage following the procedures of MIL-STD-202E. Load Life ∆R/R ± (2% + 0.05Ω) After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at 70°C. Resistance change to be within specification, with no evidence of arcing, burning or charring. Moisture Load ∆R/R ± (2% + 0.05Ω) After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at 40°C and 90-95% RH. Resistance change to be within specification, with no evidence of arcing, burning or charring. Voltage Coefficient ∆R/R < 100ppm/V Flammability Product is conformally coated with epoxy resin conforming to UL94V-0. 2 3 4 5 6 7 8 n-1 n = Number of pins Common parts are characterised by having a number of resistive elements, all of the same nominal value. All elements are connected to pin 1. 1 2 3 4 5 6 n-1 n n = Number of pins Isolated parts are characterised by having a number of resistive elements, all of the same nominal value. All elements are independent. Common (E) Isolated (M) SECTION 4