10JF MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

MODEL: 10JF 10JF SPECIFICATIONS ES-0880 Rev.11 Page 1/3 http://www.m-system.co.jp/ High-density Signal Conditioners 10-RACK 2-input MATH FUNCTION MODULE (field-programmable) Functions & Features

  • Providing temperature or pressure compensation for a gas flow, and other arithmetic operations
  • Microprocessor based
  • Equation and parameters selectable on site via hand-held programmer PU-2x
  • Loop testing
  • Optional second channel output available at the front terminals and at the Standard Rack connector Typical Applications
  • Various flowmeters
  • Adding two flows
  • Ratio calculation
  • Calculating average temperature MODEL: 10JF-[1][2][3]-R[4]

ORDERING INFORMATION

  • Code number: 10JF-[1][2][3]-R[4] Specify a code from below for each of [1] through [4]. (e.g. 10JF-6A6-R/3/Q)
  • Parameters Use Ordering Information Sheet (No. ESU 1980). Default setting will be used if not otherwise specified.
  • Specify the specification for option code /Q (e.g. /C01) [1] INPUT Current A: 4 – 20 mA DC (Input resistance 100 Ω) Voltage 6: 1 – 5 V DC (Input resistance 1 MΩ min.) [2] OUTPUT 1 Current A: 4 – 20 mA DC (Load resistance 600 Ω max.) Voltage 6: 1 – 5 V DC (Load resistance 500 Ω min.) [3] OUTPUT 2 0: None Voltage 6: 1 – 5 V DC (Load resistance 5000 Ω min.) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [4] OPTIONS (multiple selections) Equation (Refer to the EQUATION table) /1: Temperature compensation for DP flowmeter (ideal gas) /2: Pressure compensation for DP flowmeter (ideal gas) /3: Addition/subtraction /4: Multiplication /5: Division Other Options blank: none /Q: Option other than the above (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating

MODEL: 10JF 10JF SPECIFICATIONS ES-0880 Rev.11 Page 2/3 http://www.m-system.co.jp/ EQUATION Equation parameters X0: output (%) X1 to X2: input (%) K0 to K2: gain ±29.999 A0 to A2: bias (%) ±299.99 % EQUATION /1: Temperature compensation for DP fl owmeter (ideal gas) K1X1 X0 = K2X2+A 2 where X 0 : compensated fl ow (linear characteristic) X1 : uncompensated fl ow (square root extraction available) X2 : temperature /2: Pressure compensation for DP fl owmeter (ideal gas) X0 = K1X1 K2X2+A 2 where X 0 : compensated fl ow (linear characteristic) X1 : uncompensated fl ow (square root extraction available) X2 : pressure /3: Addition/subtraction /4: Multiplication X0 = K0 (K1X1+A 1) (K2X2+A 2) + A 0 /5:Division K0 (K1X1+A 1) X0 = + A 0 (K2X2+A 2)

RELATED PRODUCTS

  • Programming Unit (model: PU-2x)
  • PC configurator software (model: JXCON) Downloadable at M-System’s web site. A dedicated cable is required to connect the module to the PC. Please refer to the internet software download site or the users manual for the PC configurator for applicable cable types. GENERAL SPECIFICATIONS Construction: Rack-mounted; terminal access via screw terminals at the front and via card-edge connector at the rear; terminal cover provided Connection Input: M3.5 screw terminals (torque 0.8 N·m) Output: Card-edge connector and M3.5 screw terminals (torque 0.8 N·m) Power input: Supplied from card-edge connector Screw terminal: Nickel-plated steel Housing material: Flame-resistant resin (black) Isolation: Input to output 1 to output 2 to power (non- isolated between inputs) Overrange input: Approx. -25 to +125 % Overrange output: Approx. -10 to +120 % at 1 – 5 V Adjustments: Programming Unit (model: PU-2x); equation and parameters, square root extraction, zero and span, etc. (Refer to the users manual of JXCON for the adjustments configurable with JXCON.) INPUT SPECIFICATIONS ■ DC Current: Input resistor incorporated INSTALLATION Current consumption: Approx. 60 mA with voltage output 1 Approx. 90 mA with current output 1 Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Standard Rack 10BXx Weight: 220 g (0.49 lb) PERFORMANCE in percentage of span Accuracy: Input accuracy + output accuracy Input accuracy: ±0.2 % (gain ≤ 1) [±0.2 % × gain] with gain > 1 Output accuracy: ±0.2 % Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: ≤ 1.2 sec. (0 – 90 %) Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (input to output 1 to output 2 to power)

1500 V AC @ 1 minute (input or output or power to ground)

MODEL: 10JF 10JF SPECIFICATIONS ES-0880 Rev.11 Page 3/3 http://www.m-system.co.jp/ EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 130 (5.12) 3 (.12) 51 (2.01) 82 (3.23) 2–4.3 (.17) dia. MTG HOLE TERMINAL COVER 7–M3.5 SCREW 8 (.31) 91 (3.58) 99 (3.90 ) 25 (.98) 1 2 5 6 7 8 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM PU-2x Isolation INPUT 1

1 Multiplexer Output

  • Input shunt resistor incorporated for current input. 1 output type has the output 1 connected to the card-edge connector in parallel. Note: The section enclosed by broken line is only for 2nd output channel. OUTPUT 2 POWER INPUT 2 MODULAR JACK Specifications are subject to change without notice.