1067250000 WEIDMULLER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 1 ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Product image ACT20P: The flexible solution

  • Precise and highly functional signal converters
  • Release levers simplify handling General ordering data Version Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V Order No. 1067250000 Type ACT20P-BRIDGE-S GTIN (EAN) 4032248820856 Qty. 1 pc(s).

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Technical data Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 2 Dimensions and weights Depth 113.6 mm Depth (inches) 4.472 inch Height 119.2 mm Height (inches) 4.693 inch Width 22.5 mm Width (inches) 0.886 inch Net weight 176 g Temperatures Humidity 10…90 %, no condensation Probability of failure MTTF 543 Years Environmental Product Compliance REACH SVHC Lead 7439-92-1 Input Bridge sensitivity 1.0 mV / V to 5.0 mV / V Bridge supply voltage 5 V or 10 V Input measurement range ± 10 mV / ± 20 mV / ± 30 mV / ± 50 mV (adjustable) Number of inputs Sensor Resistance measuring bridge, Total resistance of all parallel resistance measuring bridges: min. 87Ω Sensor supply 120 mA @ 10 V (= 4 x 350 Ω bridge resistors) Output Load impedance current ≤ 600 Ω Output current 0…22 mA (adjustable) Output voltage, note 0…11 V (adjustable) Type active, connected control must be passive load impedance voltage 600 Ω Output (analogue) Type (analogue output) Voltage and current output (configurable) General data Configuration DIP switch and button Linearity Typically ± 0.05 % of signal range Long-term drift 0.1 % / 10.000 h Power consumption 3 W @ 24 V DC Rail TS 35 Repeat accuracy ± 0.05 % of final value Step response time < 400 ms (10…90 %) Temperature coefficient typ. 0.005 % / °C Type of connection Screw connection Voltage supply 10…60 V DC

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Technical data Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 3 Insulation coordination EMC standards EN 61326 Insulation voltage 5.7 kV (input / output, input / supply) Pollution severity 2 Rated voltage 300 Veff Surge voltage category III Connection data Type of connection Screw connection Tightening torque, min. 0.4 Nm Tightening torque, max. 0.6 Nm Clamping range, rated connection 2.5 mm² Clamping range, min. 0.5 mm² Clamping range, max. 2.5 mm² Wire connection cross section AWG, min. AWG 26 Wire connection cross section AWG, max. AWG 12 Classifications ETIM 6.0 EC002653 ETIM 7.0 EC002653 ETIM 8.0 EC002653 ECLASS 9.0 27-21-01-20 ECLASS 9.1 27-21-01-90 ECLASS 10.0 27-21-01-20 ECLASS 11.0 27-21-01-20

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Technical data Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 4 Tender specification sheets Long specification Bridge measuring transformer with electrical 3-way isolation, configurable measurement isolating transformer in 22.5 mm width with external power supply, for recording, transforming and isolating of measurements from industrial strain gauges. Standard DC current/ voltage signals are available on the output side. Measuring bridges of up to 3 x 350 Ohm can be supplied via the input circuit. Automatic tare calibration via external switch signal, or manually with a press of a button. 6-wire connection compensates for differences in wire resistance. Bridge excitation voltage can be switched between 5 v and 10 V . Load cells can be calibrated using a button on the front side. I/O signals can be configured via DIP switches. Add-on housing for TS35 rail mounting Dimensions: L/W/H 119.2/ 22.5/ 113.6 mm Screw connection / Nominal cross-section 2.5 mm2 Protection degree: IP Input Resistance measuring bridge / 1 mV / V... 5 mV / V Bridge sensitivity +/- (adjustable) Input resistance > 1 MOhm Bridge supply

5 V or 10 V

< 600 Ohm/ Strom/> 1 kOhm/ voltage Temperature coefficient typ. 50 ppm / K Transmission error typ. 0.05 % of input Step response time < 400 ms (10...90 %) Auxiliary power 10...60 VDC Ambient temperature range -40°C...+70 °C Isolation EN 50178, 3-way isolation up to 5.7 kV of all circuits against each other Test voltage 4 kV input against output against auxiliary power Rated voltage

300 V AC/DC at

isolation, configurable measurement isolating transformer in 22.5 mm width with external power supply, for recording, transforming and isolating of measurements from industrial strain gauges. Standard DC current/ voltages signals are available on the output side. Measuring bridges of up to 3 x 350 Ohm can be supplied via the input circuit. Automatic tare calibration via external switch signal, or manually with a press of a button. 6-wire connection compensates for differences in wire resistance. Bridge excitation voltage can be switched between 5 v and 10 V . Load cells can be calibrated using a button on the front side. I/O signals can be configured via DIP switches.

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Technical data Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 5 Important note Product information The ACT20P-BRIDGE-S bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is electrogalvanised and isolated from the input and output (3-way isolation). Properties

  • 4-wire and 6-wire measurement
  • Supply of up to 4 parallel-connected measuring bridges each with 350 Ω
  • Input and output ranges can be adjusted via DIP switches
  • Tara compensation via external button or PLC signal
  • Operating status display on a front panel LED
  • Galvanic 3-way isolation between input, output and supply. Approvals Approvals Approvals CULUS; ROHS Conform Downloads Approval/Certificate/Document of Conformity Declaration of Conformity Engineering Data STEP Engineering Data EPLAN, WSCAD Software DIP switch configuration tool User Documentation Quickstart_german.pdf Instruction sheet Catalogues Catalogues in PDF-format Brochures

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Drawings Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 6 Electric symbol Dimensioned drawing example for DIP switch setting (with ACT20 tool)

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Accessories Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 7 Blank ESG is the tried-and-tested marker in MultiCard format for use on many well-known electrical devices. The result is high-quality device marking with a high-contrast appearance. Various types are available for devices from manufacturers like Siemens, ABB, Beckhoff etc. Advantages at a glance:

  • Tags for universal usage, self-adhesive or clip-on tags, depending on type
  • For aligned equipment, e.g. circuit breakers, we supply ESG markers for clipping onto tag rails
  • Individual laser-quality printing according to specifications For custom printing: Please send us a file of our labeling software M-Print PRO or M-Print PRO Online (without installation) for your labeling specifications. General ordering data VersionType ESG 6.6/20 BHZ 5.00/04 Order No. 1082540000 GTIN (EAN) 4032248845439 Qty. 200 pc(s). ESG, Device markers x 20 mm, PA 66, Colour: white

ACT20P-BRIDGE-S Weidmüller Interface GmbH & Co. KG Klingenbergstraße 26 D-32758 Detmold Germany www.weidmueller.com Accessories Creation date October 2, 2021 5:33:51 AM CEST Catalogue status 27.09.2021 / We reserve the right to make technical changes. 8 Blank ESG is the tried-and-tested marker in MultiCard format for use on many well-known electrical devices. The result is high-quality device marking with a high-contrast appearance. Various types are available for devices from manufacturers like Siemens, ABB, Beckhoff etc. Advantages at a glance:

  • Tags for universal usage, self-adhesive or clip-on tags, depending on type
  • For aligned equipment, e.g. circuit breakers, we supply ESG markers for clipping onto tag rails
  • Individual laser-quality printing according to specifications For custom printing: Please send us a file of our labeling software M-Print PRO or M-Print PRO Online (without installation) for your labeling specifications. General ordering data VersionType ESG 8/13.5/43.3 SAI AU Order No. 1912130000 GTIN (EAN) 4032248541164 Qty. 5 pc(s). ESG, Device markers x 13.5 mm, PA 66, Colour: Transparent