DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

ADL Embedded Solutions GmbH, Eiserfelder Straße 316 D-57080 Siegen, ADL Embedded Solutions Inc., 4411 Morena Blvd., Suite 101 Germany P. +49 (0) 271 250 810 0 F. +49 (0) 271 250 810 20 San Diego, CA 92117-4345 P. +1 858 490-0597 F. +1 858 490-0599 PC/104 - Peripherals Embedded Solutions 104-PWR-500A - Wide Range DC/DC PC/104 Power Module

FEATURES

 PC/104 Bus 30/40Watt DC/DC Power Supply  Up to 84% Efficiency  Three Wide Input Voltage Ranges: 12V Nominal, 9VDC-18VDC(30W) 24V Nominal, 18VDC-36VDC(40W) 48V Nominal, 36VDC-75VDC(40W)  Output Voltage and Current: +12V Input: +5VDC at 6A Max +24V Input: +5VDC at 8A Max +48V Input: +5VDC at 8A Max  Voltage Status LEDs  Reverse Power Protection on Inputs  Resettable Fused Input Line  Fully Protected Outputs  Can be populated on either side of the board to allow for heat-sinking in fanless application re- quirements  Temperature range with heatsink -40 to +65°C, up to 105°C with derating of 2% per °C (no air flow) FUNCTIONAL DESCRIPTION The design incorporates a 16-bit pass through PC/104 connector, molex type power input connector and voltage status LED’s. Since heat is always a factor to consider in any system design project, this module can be populated on either side of the board to facilitate heat sinking to one end of an enclosure, with the CPU heat sinking to the other end of the enclosure. This single output version can be ordered with or without a heatsink. At up to 84% efficiency, a dynamic input range and full protection on inputs and outputs, this power supply is very versatile and appropriate for many PC/104 based applications. The Input Power Connector is a Four-pin standard Molex type connector at the edge of the board. It’s the same connector as used on a CD-ROM so it’s easy to set up and test a system with a local +12V Computer type power supply.

ADL Embedded Solutions GmbH, Eiserfelder Straße 316 D-57080 Siegen, ADL Embedded Solutions Inc., 4411 Morena Blvd., Suite 101 Germany P. +49 (0) 271 250 810 0 F. +49 (0) 271 250 810 20 San Diego, CA 92117-4345 P. +1 858 490-0597 F. +1 858 490-0599 PC/104 - Peripherals Embedded Solutions Specifications

Ordering Information

104-PWR-500A-12 12V power supply 104-PWR-500A-24 24V power supply 104-PWR-500A-48 48 V power supply NOTE - Specify "-HS" as a suffix for heat sink version. Specify "-R" for population of DC/ DC converter on reverse side of board. Block Diagram Output Characteristics OutputVoltage Set Point on 5V: ±1%, Factory set Load Regulation ±0.5% Measured from Full Load to 10% load Temperature Coeffcient ±0.01%/°C Ripple/Noise on 5V 60mV P-P measured at 20MHz bandwidth Short Circuit Protection Indefinite, Automatic Recovery Overvoltage Protection 120% Clamp type Input Characteristics 12 24 48 Unit/Comments Input Voltage 9-18 18-36 36-75 VDC Under Voltage Shut Down 8 16 33 VDC (min) Over Voltage Shut Down 20 40 80 VDC (max) Minimum Input Current 0 0 0 A (min) Full Load Input Current 3.2 2 1 A (max) Efficiency by Model 81 83 84 % Switching Frequency 360 to 440 360 to 440 360 to 440 KHz Factory set Operating Temperature -40 to +65 -40 to +65 -40 to +65 °C up to 105°C with derating of 2% per °C (no air flow) Storage Temperature -55 to +125 -55 to +125 -55 to +125 °C Relative Humidity 5 to 95 5 to 95 5 to 95 % non-condensing Note: CE testing & approval must be done at the system level, in the designed enclosure, and is not done on individual boards.