1011-255-0205 | DigiCamel IC Datasheet

Online Datasheet

Read 1011-255-0205 online.

DTMH04-3PA TEC | Alldatasheet

Document overview

Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
PDF pages: 16

Technical content

Datasheet sections

Deutsch DT, DTM, and DTP Series environmentally sealed connectors are designed speciﬁ cally for cable to cable applications. The DT connectors are used in harsh environment applications where even a small degradation in connection may be critical. Thermoplastic housings offer a wide operating temperature range and silicone rear wire and interface seals allow the connectors to withstand conditions of extreme temperature and moisture. The connector may be populated with either solid or stamped & formed style contacts. Contact insertion and removal does not require any special tools. Contacts are retained in locked position by dielectric ﬁ ngers which are molded as an integral part of the housing. Secondary wedgelocks are assembled at the mating interfaces to ensure contact positioning. The Deutsch DT Series general purpose connectors will provide reliability and performance on the engine or transmission, under the hood, on the chassis, or in the cab. DT* 06 - 2 S * - XXXX Series Blank = DT Series M = DTM Series P = DTP Series Style 04 = Receptacle 06 = Plug Special Modiﬁ cations Key (if applicable) Contacts P = Pin S = Socket Conﬁ guration  DT Family Part Numbering System  DT Series Overview Deutsch’s DT Series connectors offer ﬁ eld proven reliability and rugged quality. The DT design strengths include optional ﬂ ange mounting, multi-pin arrangements, lower cost, and design ﬂ exibility. The DT Series offers the designer the ability to use multiple size 16 contacts, each with 13 amp continuous capacity, within a single shell.  DTM Series Overview Deutsch’s DTM Series connectors are the answer to all of your smaller wire gauge applications. Building on the DT design strengths, the DTM connector line was developed to ﬁ ll the need for lower amperage, multi- pin, inexpensive connectors. The DTM Series offers the designer the ability to use multiple size 20 contacts, each with 7.5 amp continuous capacity, within a single shell.  DTP Series Overview Deutsch’s DTP Series connectors are the solution for your power application requirements. Building on both the DT and DTM design strengths, the DTP connector line was developed to ﬁ ll the need for higher amperage, multi-pin, inexpensive connectors. The DTP Series offers the designer the ability to use multiple size 12 contacts, each with a 25 amp continuous capacity, within a single shell. The DTP connectors are currently available in two and four pin conﬁ gurations.

A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F 8 1.217 (30.91) .776 Dimensions are for reference only.  DT Series Dimensions F D E F D AC B A C Cavity DTP Plug DTP Receptacle Overall Length A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F Dimensions are for reference only.  DTP Series Dimensions F D E F D A C B A C Cavity DTM Plug DTM Receptacle Overall Length A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F 8 1.720 (43.69) Dimensions are for reference only.  DTM Series Dimensions F E D F DAC B A C

DTP0*-2* 2 size 12 DTP0*-4* 4 size 12 DT04-4P 4 size 16 X, X, X Keying Options A = A key B = B key C = C key D = D key Insert Arrangement Insert Layout Number and Size of Cavities  DT Family Connector Conﬁ gurations DTM0*-08** 8 size 20 A, B, C, D DTM0*-12** 12 size 20 A, B, C, D DTM0*-2* 2 size 20 DTM0*-3* 3 size 20 DTM0*-4* 4 size 20 DTM0*-6* 6 size 20  DTM Series Conﬁ gurations DT0*-08** 8 size 16 A, B, C, D DT0*-12** 12 size 16 A, B, C, D DT0*-6* 6 size 16 DT0*-2* 2 size 16 DT0*-3* 3 size 16 DT0*-4* 4 size 16  DT Series Conﬁ gurations  DTP Series Conﬁ gurations

WP-2P Wedgelock for 2 way receptacle WP-2S Wedgelock for 2 way plug WP-4P Wedgelock for 4 way receptacle WP-4S Wedgelock for 4 way plug W W DT Series Wedgelocks Receptacle Plug W2P* Wedgelock for 2 way receptacle *A, B, C, D keying available W2S* Wedgelock for 2 way plug *A, B, C, D keying available W3P* Wedgelock for 3 way receptacle *J1939 keying available W3S* Wedgelock for 3 way plug *J1939 keying available W4P* Wedgelock for 4 way receptacle *A, B, C, D keying available W4S* Wedgelock for 4 way plug *A, B, C, D keying available W6P Wedgelock for 6 way receptacle W6S Wedgelock for 6 way plug W8P Wedgelock for 8 way receptacle W8S Wedgelock for 8 way plug W12P Wedgelock for 12 way recep- tacle W12S Wedgelock for 12 way plug W W W W W W Required Components  Secondary Wedgelocks Deutsch DT style electrical connectors require secondary wedgelocks which are sold separately. The wedgelocks ensure proper contact alignment within each connector. Secondary wedgelocks are assembled at the mating interface and click into place. If by chance the secondary wedgelocks are not properly seated during assembly, they will be pressed into locked position during the mating of the connector. Adding to the design ﬂ exibility of the DT Series, several wedgelocks offer keying options. Wedgelocks for enhanced seal retention plugs (P012) are also available. Jiffy Splices accept one pin and one socket. Note Jiffy Splices accept one pin and one socket. Note Note Wedgelocks for enhanced plugs (P012) are available. NoticeNotice

Special Modiﬁ cations The DT Series connectors offer several modiﬁ cations to enhance the design ﬂ exibility and meet application speciﬁ c needs. Options include enhanced seal retention, ﬂ anges, and connector body color just to mention a few. By combining the DT Series connectors with the available modiﬁ cations and accessories, the design possibilities are immense. DTM Series Wedgelocks Receptacle Plug WM-2P* Wedgelock for 2 way receptacle *A, B, C, D keying available WM-2S* Wedgelock for 2 way plug *A, B, C, D keying available WM-3P Wedgelock for 3 way receptacle WM-3S Wedgelock for 3 way plug WM-4P Wedgelock for 4 way receptacle WM-4S Wedgelock for 4 way plug WM-6P Wedgelock for 6 way receptacle WM-6S Wedgelock for 6 way plug WM-8P Wedgelock for 8 way receptacle WM-8S Wedgelock for 8 way plug WM-12P Wedgelock for 12 way recep- tacle WM-12S Wedgelock for 12 way plug W W W W W W W W W W W  B016 Modiﬁ cation The B016 receptacle modiﬁ cation provides safety against mis-mating. The B016 is available for the DT 12 way connectors, DT13/15, and DTF13/15 PCB Series connec- tors. In addition to the four keying positions (A, B, C, or D) and color coding, the B016 enhancement gives the user both visual and tactile proof of correct mating, thus eliminating mis-mating opportunities during assembly. Please note the P012 plug is the required mate for the B016 receptacle to make the enhancement effective.  P012 Modiﬁ cation The DT P012 plugs provide enhanced front seal reten- tion providing an ultra tight environmental seal. The enhanced seal retention keeps the seal in place during mating and unmating. The P012 modiﬁ cation requires an enhanced P012 wedgelock. Deutsch’s P012 modiﬁ cation is available in 2, 3, 4, 6, 8, and 12 cavity arrangements. P012 plugs have a black connector body except for the 8 and 12 cavity arrangements, where the color is based on the key.

 E007 & E008 Modiﬁ cation To meet the application requirements where wires need added protection, the DT (E008) and DTM (E007) Series may be supplied with shrink boot adapters. These adapters accept shrink tubing.  C015 Modiﬁ cation The C015 modiﬁ cation offers a reduced diameter insert cavity allowing for a proper seal with smaller wire insula- tion. The C015 modiﬁ cation is also referred to as an “ E” seal.  E004 Modiﬁ cation The E004 modiﬁ cation changes the connector body color to black.  Flange Modiﬁ cations Designed to simplify wire routing and assembly, DT Series receptacles are available in many mounting conﬁ gura- tions and styles. Welded ﬂ ange

Welded flange - BL04, BL08, CL03, L012, LE14
Welded flange, end cap - LE07, LE11
Welded flange, shrink boot adapter - LE08, LE12 Sealed ﬂ ange
Sealed flange, end cap - CL09, LE01, LE05, LE06, LE09, LE10, LE17, LE21
Sealed flange, shrink boot adapter - BL10, CL07  E003 Modiﬁ cation The E003 modiﬁ cation offers a protective end cap attached to the rear of the connector. There are holes in the cap to allow the contacts to be inserted.  E005 Modiﬁ cation The E005 modiﬁ cation offers a protective end cap attached to the rear of the connector and has a black connector body. Jiffy Splices accept one pin and one socket. Note Jiffy Splices accept one pin and one socket. Note Note For additional modiﬁ cations, please consult the factory. NoticeNotice

Deutsch Industrial offers several accessory items that can be used to complement the connectors. The DT family accessories include items such as boots, backshells, gaskets, dust caps, and mounting clips. They are designed to assist in completing the design requirements of speciﬁ c applications. Accessory items cover a wide array of design requirements such as assisting with mounting, providing additional protection, and offering increased aesthetics. Gasket P/N Connector P/N DT3P-L012-GKT DT04-3P-L012 DT4P-L012-GKT DT04-4P-L012 DTP4P-L012-GKT DTP04-4P-L012 DT8P-L012-GKT DT04-08P*-L012 DT12-L012-GKT DT04-12P*-L012 DTM04-12P*-L012  Gaskets Moisture, dirt, salt, sand, and road debris can all work their way into electrical panels through unsealed mounting ﬂ anges. Rated to operate in environments from -70°F to +225°F, these rugged high quality neoprene gaskets form a tight seal between the panel face and connector ﬂ ange to help keep out destructive elements. The gaskets have a thickness of .125” and meet the UL-94-HBF, Mil-R-6130C, and FMVSS-302 ﬂ ammability speciﬁ cations.  Dust Caps The DT Series dust caps are made of either thermoplastic or durable plastisol and are designed to provide protection for the connector interface when the two halves are not mated. The plastisol caps, available for plugs and receptacles, are ideal for providing temporary protection from dirt, dust, and paint overspray. The thermoplastic caps provide an environmental seal for an unmated plug. Plastisol Dust Cap P/N Connector P/N DTM3S-DC DTM06-3S DT3P-DC DT04-3P DT4P-DC DT04-4P DT6P-DC DT04-6P DTM12P-DC DTM04-12P* DT12P-DC, DT12P-DC-BK DT04-12P* DT12S-DC DT06-12S* Thermoplastic Dust Cap P/N Connector P/N 1011-344-0205 DT06-2S 1011-345-0305 DT06-3S 1011-346-0405 DT06-4S 1011-347-0605 DT06-6S 1011-348-0805 DT06-08S* 1011-349-1205 DT06-12S*

Receptacle Boot Description Boot Part Number DT Series DTM Series DTP Series 2 way receptacle boot, gray DT2P-BT DTM2P-BT DTP2P-BT 2 way receptacle boot, black DT2P-BT-BK DTM2P-BT-BK DTP2P-BT-BK 3 way receptacle boot, gray DT3P-BT DTM3P-BT - 3 way receptacle boot, black DT3P-BT-BK - - 4 way receptacle boot, gray DT4P-BT DTM4P-BT DTP4P-BT 4 way receptacle boot, gray, enhanced length - - DTP4P-BT-EN 6 way receptacle boot, gray DT6P-BT DTM6P-BT - 6 way receptacle boot, black DT6P-BT-BK - - 8 way receptacle boot, gray DT8P-BT DTM8P-BT - 8 way receptacle boot, black DT8P-BT-BK - - 12 way receptacle boot, gray DT12P-BT DTM12P-BT - 12 way receptacle boot, black DT12P-BT-BK DTM12P-BT-BK - 12 way receptacle boot, gray, enhanced length DT12P-BT-EN - - Plug Boot Description Boot Part Number DT Series DTM Series DTP Series 2 way plug boot, gray DT2S-BT DTM2S-BT DTP2S-BT 2 way plug boot, black DT2S-BT-BK DTM2S-BT-BK - 3 way plug boot, gray DT3S-BT DTM3S-BT - 3 way plug boot, black DT3S-BT-BK DTM3S-BT-BK - 4 way plug boot, gray DT4S-BT DTM4S-BT DTP4S-BT 4 way plug boot, gray, enhanced length - - DTP4S-BT-EN 6 way plug boot, gray DT6S-BT DTM6S-BT - 6 way plug boot, black DT6S-BT-BK - - 8 way plug boot, gray DT8S-BT DTM8S-BT - 8 way plug boot, black DT8S-BT-BK DTM8S-BT-BK - 12 way plug boot, gray DT12S-BT DTM12S-BT - 12 way plug boot, black DT12S-BT-BK DTM12S-BT-BK - 12 way plug boot, gray, enhanced length DT12S-BT-EN - - 48 way plug boot, gray DT48S-BT - -  Boots Boots provide a professional looking ﬁ nishing touch for your Deutsch DT family connectors. Made of du- rable plastisol, these slip-on boots are not only aesthetically appealing, but also provide increased protection from dirt, paint overspray, and pressure washing. The plastisol boots are rated from -20° F to +212° F and offer a slip-on design making installation quick and easy.

(mm) P/N DT04-2P 180° 6, 7.5, 8.5, and 10 1011-229-0205 180° X 6, 7.5, 8.5, and 10 1011-257-0205 90° 6, 7.5, 8.5, and 10 1011-230-0205 90° X 6, 7.5, 8.5, and 10 1011-258-0205 DT04-3P 180° 6, 7.5, 8.5, and 10 1011-233-0305 180° X 6, 7.5, 8.5, and 10 1011-261-0305 90° 6, 7.5, 8.5, and 10 1011-234-0305 90° X 6, 7.5, 8.5, and 10 1011-262-0305 DT04-4P 180° 6, 7.5, 8.5, and 10 1011-237-0405 180° X 6, 7.5, 8.5, and 10 1011-265-0405 90° 6, 7.5, 8.5, and 10 1011-238-0405 90° X 6, 7.5, 8.5, and 10 1011-266-0405 DT04-6P 180° 8.5, 10, and 13 1011-241-0605 180° X 8.5, 10, and 13 1011-269-0605 90° 8.5, 10, and 13 1011-242-0605 90° X 8.5, 10, and 13 1011-270-0605 DT04-08P* 180° 8.5, 10, and 13 1011-245-0805 90° 8.5, 10, and 13 1011-246-0805 DT04-12P* 180° 10, 13, and 17 1011-249-1205 90° 10, 13, and 17 1011-250-1205 Plug Backshells Connector Style Strain Relief Tubing Size (mm) P/N DT06-2S 180° 6, 7.5, 8.5, and 10 1011-227-0205 180° X 6, 7.5, 8.5, and 10 1011-255-0205 90° 6, 7.5, 8.5, and 10 1011-228-0205 90° X 6, 7.5, 8.5, and 10 1011-256-0205 DT06-3S 180° 6, 7.5, 8.5, and 10 1011-231-0305 180° X 6, 7.5, 8.5, and 10 1011-259-0305 90° 6, 7.5, 8.5, and 10 1011-232-0305 90° X 6, 7.5, 8.5, and 10 1011-260-0305 DT06-4S 180° 6, 7.5, 8.5, and 10 1011-235-0405 180° X 6, 7.5, 8.5, and 10 1011-263-0405 90° 6, 7.5, 8.5, and 10 1011-236-0405 90° X 6, 7.5, 8.5, and 10 1011-264-0405 DT06-6S 180° 8.5, 10, and 13 1011-239-0605 180° X 8.5, 10, and 13 1011-267-0605 90° 8.5, 10, and 13 1011-240-0605 90° X 8.5, 10, and 13 1011-268-0605 DT06-08S* 180° 8.5, 10, and 13 1011-243-0805 90° 8.5, 10, and 13 1011-244-0805 DT06-12S* 180° 10, 13, and 17 1011-247-1205 90° 10, 13, and 17 1011-248-1205 Connector F P [N] FT [N] DT04-2P / DT06-2S 50 / 50 50 / 10 DT04-3P / DT06-3S 50 / 50 50 / 50 DT04-4P / DT06-4S 50 / 50 50 / 25 DT04-6P / DT06-6S 50 / 50 50 / 30 DT04-08P* / DT06-08S* 50 / 50 50 / 35 DT04-12P* / DT06-12S* 50 / 50 50 / 40 90° 90° FT FP FP FT  Backshells The Deutsch DT Series backshells are designed to snap onto and mate with all standard (basic plug and receptacles without modiﬁ cations) DT Series connectors. The rigid, durable backshells offer a high level of protection and allow convoluted tubing to nest within the rear of the backshell. Straight (180°) and right angle (90°) versions and backshells with strain relief for jacketed cable are also available. The backshells are available for both standard plugs and standard receptacles. Since they are designed to work with the standard DT connectors, tests should be conducted for ﬁ t and function of a backshell being used on any part with a modiﬁ cation.  Pull Off Strength

Mounting Clip Part Number Used On (Receptacles) Mounting Direction Color/Material Hole O.D. inches (mm) 1027-003-1200 DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Stainless steel .433 (11.0) 1027-005-1200 DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Stainless steel .512 (13.0) 1027-004-1200 DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Steel w/ zinc plating .512 (13.0) 1027-008-1200 DT 2, 3, 4, 6, 12 DTM, DTP (all) Side Steel w/ zinc plating .433 (11.0) 1027-013-1200 DT 2, 3, 4, 6, 12 DTM, DTP (all) Side Steel w/ zinc plating .323 (8.2) 1027-001-0800 DT 8 cavity only Straight Stainless steel .433 (11.0) 1027-006-0800 DT 8 cavity only Straight Stainless steel .512 (13.0) 1027-002-0800 DT 8 cavity only Straight Steel w/ zinc plating .512 (13.0) 1027-014-0800 DT 8 cavity only Straight Steel w/ zinc plating .323 (8.2) 1011-026-0205 DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Gray plastic .200 (5.08) 1011-030-0205 DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Black plastic --- 1011-310-0205* *Connector removeable with 50N of force DT 2, 3, 4, 6, 12 DTM, DTP (all) Straight Black plastic --- 1011-027-0805 DT 8 cavity only Straight Gray plastic .200 (5.08)  Mounting Clips Mounting clips are used to mount DT Series connectors. To meet design needs, the clips are available for several conﬁ gurations and in plastic or stainless steel.

WV-18P Wedgelock for 18 way receptacle WV-18S Wedgelock for 18 way plug DTV Series Overview Deutsch’s DTV Series connectors offer the same time tested reliability and performance as the DT Series, with the added ﬂ exibility of an 18 cavity ﬂ anged design. Deutsch con- tinues its tradition of providing an environmentally sealed connector to meet even your toughest application needs. DTV 06 - 18 S * Series Style 02 = Receptacle 06 = Plug Conﬁ guration Key A, B, C, or D Contacts P = Pin S = Socket Cavity DTV Plug DTV Receptacle Overall Length A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F Dimensions are for reference only.  DTV Series Part Numbering System  DTV Series Dimensions  Secondary Wedgelocks E F D F D B C A C A

The DTMH is an environmentally sealed, high temperature connector capable of operat- ing in temperatures -55° to +150°C. The DTMH accepts size 20 contacts and carries 7.5 amps each. The DTMH connectors feature an integrated TPA for easy assembly. Cavity DTMH Plug DTMH Receptacle Overall Length A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F Dimensions are for reference only.  DTMH Series Dimensions A C B A C F E D F D DTMH0*-2** 2 size 20 DTMH0*-3** 3 size 20 DTMH0*-4** 4 size 20  DTMH Series Conﬁ gurations DTMH 04 - 2 P * Series Style 04 = Receptacle 06 = Plug Conﬁ guration Key A, B, C, or D Contacts P = Pin S = Socket  DTMH Series Part Numbering System

A Overall Height B Overall Width C Overall Length D Overall Height E Overall Width F Dimensions are for reference only.  DTMN Series Dimensions E D F B A C A C DTMN Series Overview The DTMN is a non-environmentally sealed connector. The DTMN is available in a 2 or 3 cavity connector and accepts size 20 contacts. The DTMN connector is designed to offer Deutsch quality and reliability when a sealed connector is not required. DTMN0*-2** 2 size 20 DTMN0*-3** 3 size 20  DTMN Series Conﬁ gurations DTMN 04 - 2 P Series Style 04 = Receptacle 06 = Plug Contacts P = Pin S = Socket Conﬁ guration  DTMN Series Part Numbering System

Step 1: Grasp crimped contact ap- proximately one inch behind the contact barrel. Step 2: Hold connector with rear grommet facing you. Step 3: Push contact straight into connector grommet until a click is felt. A slight tug will conﬁ rm that it is properly locked in place. Step 4: Once all contacts are in place, insert green wedge. The green wedge will snap into place. How To Instructions  Contact Insertion Step 1: Remove green wedge using needlenose pliers to pull wedge straight out. Step 2: To remove the contacts, gently pull wire backwards, while at the same time releasing the locking ﬁ nger by moving it away from the contact with a screwdriver. Step 3: Hold the rear seal in place, as removing the contact will displace the seal.  Contact Removal Note Jiffy Splices accept one pin and one socket. Note e e Jiffy Splices accept one pin and one socket. Note N N N Note ote ote No No o o o o te te te te N N N N N N N N t t N N Note The receptacle is shown, use the same procedure for the plug. NoticeNotice

Product Information

1011-255-0205 specifications and overview.

Summary

DT Family

Description

DT Family

Source title 1011-255-0205 Datasheet(PDF) - TE Connectivity Ltd

Related Parts

More parts from the same family.

Browse manufacturer