450-0035 LSTD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 33
Technical content
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2010-2014 LSR Page 1 of 33 Integrated Transceiver Modules for ZigBee / 802.15.4 (2.4 GHz) ZIGBEE LIGHT LINK (ZLL) MODULE
FEATURES
100mW output power Long range: 4000 feet Miniature footprint: 0.9” x 1.63” Integrated PCB F antenna or U.FL connector for external antenna Integrated 8051 microcontroller with 256k FLASH and 8k RAM 4MBit Serial FLASH Supports ZigBee Light Link (ZLL) Low power operation RoHS compliant Streamlined development with LSR design services. License options available to purchase design or integrate design.
APPLICATIONS
Lighting Control Smart Energy
DESCRIPTION
The ProFLEX01-SOC module is a high performance 2.4 GHz ZigBee / IEEE 802.15.4 System-On-Chip (CC2530) radio/microcontroller and power amplifier (CC2591) in a cost effective, pre-certified footprint. The module comes preloaded with the TI Z-Stack with the ZigBee Light Link protocol. Full debug and programming capabilities are included to develop custom applications. Need to get to market quickly? Not an expert in 802.15.4 or ZigBee? Need a custom antenna? Would you like to own the design? Would you like a custom design? Not quite sure what you need? Do you need help with your host board? LS Research Design Services will be happy to develop custom hardware or software, integrate the design, or license the design so you can manufacture yourself. Contact us at sales@lsr.com or call us at 262-375-4400
ORDERING INFORMATION
450-0035 ProFLEX01-SOC Module with PCB F antenna 450-0044 ProFLEX01-SOC Module with U.FL connector for external antenna 450-0051 ProFLEX01-SOC Development Kit Table 1 Orderable ProFLEX01-SOC Model Numbers
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 2 of 33 MODULE ACCESSORIES Order Number Description 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector 080-0001 U.FL to Reverse Polarity SMA Bulkhead Cable 105mm
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 3 of 33 BLOCK DIAGRAM CC2530 SOC
8051 Microcontroller
(PA/LNA) Antenna AnalogGPIO PGM/DBG TMR/PWM Serial FLASH (4MBit) Figure 1 ProFLEX01-SOC Module Block Diagram – High-Level
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 4 of 33 TABLE OF CONTENTS
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 5 of 33
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 6 of 33 MODULE PINOUT AND PIN DESCRIPTIONS MCU# GND 1 Texas Instruments CC2530
69 GND MCU#
- GND 2 68 GND - - GND 3 67 GND - - NC 4 66 NC - - NC 5 65 NC - - NC 6 64 NC - - NC 7 63 NC - - NC 8 62 NC - - NC 9 61 P0.3/W LED 16 35 Debug Data 10 60 P0.2 17 34 Debug Clock 11 59 P0.5/G LED 14 - NC 12 58 P0.4/B LED 15 - NC 13 57 NC - 20 nRESET 14 56 NC - - NC 15 55 NC - - NC 16 54 NC - - NC 17 53 NC - - NC 18 52 NC - - NC 19 51 NC - 19 P0.0/Mode 20 50 NC - - NC 21 49 NC - 12 P0.7/Button 22 48 NC - - NC 23 47 NC - - NC 24 46 NC - - NC 25 45 NC - - VCC - 3V3DC 26 44 GND - 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 P2.0 P1.0 P1.2/Light Sel NC P0.7/Button NC NC NC P1.6 P1.7/R LED NC NC NC NC NC NC NC Figure 2 Module Pinout
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 7 of 33 Module Pin Name MCU Pin Type Description
1 GND N/A GND Ground
2 GND N/A GND Ground
3 GND N/A GND Ground
4 NC N/A NC No Connect
5 NC N/A NC No Connect
6 NC N/A NC No Connect
7 NC N/A NC No Connect
8 NC N/A NC No Connect
9 NC N/A NC No Connect
10 Debug Data 35 I/O Debug Data signal for programming/debugging. 11 Debug Clock 34 Input Debug Clock signal for programming/debugging.
12 NC N/A NC No Connect
13 NC N/A NC No Connect
15 NC N/A NC No Connect
16 NC N/A NC No Connect
17 NC N/A NC No Connect
18 NC N/A NC No Connect
19 NC N/A NC No Connect
20 P0.0 19 I/O General-purpose digital I/O or Mode select. With the ZLL firmware this pin will select test mode or normal mode. Logic low will select test mode For peripheral functionality see CC2530 User’s Guide.
21 NC N/A NC No Connect
22 P0.7 12 I/O General-purpose digital I/O or button input. With the ZLL firmware this pin can be used as a multi-function button. For peripheral functionality see CC2530 User’s Guide.
23 NC N/A NC No Connect
24 NC N/A NC No Connect
25 NC N/A NC No Connect
26 VCC - 3V3DC VCC VCC Supply Voltage
27 P2.0 36 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 8 of 33 Module Pin Name MCU Pin Type Description 28 P1.0 11 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 29 P1.2 8 I/O General-purpose digital I/O or light select. With the ZLL firmware this pin will be used to select whether the light is a white fixture or and RGB light. Logic low will select RGB light. For peripheral functionality see CC2530 User’s Guide.
30 NC N/A NC No Connect
31 P0.7 12 I/O General-purpose digital I/O or button input. With the ZLL firmware this pin can be used as a multi-function button. For peripheral functionality see CC2530 User’s Guide.
32 NC N/A NC No Connect
33 NC N/A NC No Connect
34 NC N/A NC No Connect
35 P1.6 38 I/O General-purpose digital I/O UART transmit data output in test mode. For peripheral functionality see CC2530 User’s Guide. 36 P1.7/Red LED PWM 37 I/O General-purpose digital I/O UART receive data input in test mode. Red LED PWM in normal mode. For peripheral functionality see CC2530 User’s Guide.
37 NC N/A NC No Connect
38 NC N/A NC No Connect
39 NC N/A NC No Connect
40 NC N/A NC No Connect
41 NC N/A NC No Connect
42 NC N/A NC No Connect
43 NC N/A NC No Connect
44 GND N/A GND Ground
45 NC N/A NC No Connect
46 NC N/A NC No Connect
47 NC N/A NC No Connect
48 NC N/A NC No Connect
49 NC N/A NC No Connect
50 NC N/A NC No Connect
51 NC N/A NC No Connect
52 NC N/A NC No Connect
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 9 of 33 Module Pin Name MCU Pin Type Description
53 NC N/A NC No Connect
54 NC N/A NC No Connect
55 NC N/A NC No Connect
56 NC N/A NC No Connect
57 NC N/A NC No Connect
58 P0.4/Blue LED PWM 15 I/O General-purpose digital I/O or blue LED PWM. For peripheral functionality see CC2530 User’s Guide. 59 P0.5/Green LED PWM 14 I/O General-purpose digital I/O or green LED PWM. For peripheral functionality see CC2530 User’s Guide. 60 P0.2 17 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 61 P0.3/White LED PWM 16 I/O General-purpose digital I/O or white LED PWM. For peripheral functionality see CC2530 User’s Guide.
62 NC N/A NC No Connect
63 NC N/A NC No Connect
64 NC N/A NC No Connect
65 NC N/A NC No Connect
66 NC N/A NC No Connect
67 GND N/A GND Ground
68 GND N/A GND Ground
69 GND N/A GND Ground
Table 2 ProFLEX01-SOC Module Pin Descriptions
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 11 of 33 Figure 4 CC2530 SOC Block Diagram
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 12 of 33 PA/LNA The CC2591 is a cost-effective and high performance RF Front End for low-power and low-voltage 2.4 GHz wireless applications. It is a range extender for all existing and future 2.4 GHz low-power RF transceivers, transmitters and System-on-Chip products from Texas Instruments. It increases the link budget by providing a power amplifier for increased output power, and a LNA with low noise figure for improved receiver sensitivity. It provides a small size, high output power RF design with its 4x4-mm QFN-16 package. It contains PA, LNA, switches, RF-matching, and balun for simple design of high performance wireless applications. Figure 5 shows a block diagram of the CC2591. Figure 5 CC2591 Block Diagram Antenna Options The ProFLEX01-SOC module includes an integrated PCB F-antenna. An optional configuration with a u.fl connector is also available. The module regulatory certification has been completed with the following antennas: PCB trace antenna LS Research 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector and LS Research 080-0001 u.fl to Reverse Polarity SMA Bulkhead Cable (105mm in length) An adequate ground plane is necessary to provide good efficiency. The ground plane of the host board on which the module is mounted increases the effective antenna ground plane size and improves the antenna performance. The environment the module is placed in will dictate the range performance. The non-ideal characteristics of the environment will result in the transmitted signal being reflected, diffracted, and scattered. All of these factors randomly combine to create extremely complex scenarios that will affect the link range in various ways.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 13 of 33 It is also best to keep some clearance between the antenna and nearby objects. This includes how the module is mounted in the product enclosure. Unless the items on the following list of recommendations are met, the radiation pattern can be heavily distorted. Whichever antennas are used, it is best to keep a few things in mind when determining their location. Never place ground plane or copper trace routing underneath the antenna. LSR recommends keeping metal objects as far away from the antenna as possible. At a very minimum keep the antennas at least 16mm from any metallic objects, components, or wiring. The farther the antenna is placed from these interferers, the less the radiation pattern and gain will be perturbed Do not embed the antenna in a metallic or metalized plastic enclosure. Try to keep any plastic enclosure greater than 1 cm from the antenna in any orientation. Serial FLASH Memory The ProFLEX01-SOC module includes a 4MBit (512k Byte) serial FLASH memory chip. The primary intention of the serial FLASH is to support applications that require Over-The-Air (OTA) firmware downloading. For these applications the new firmware image can get sent to the module and stored in the serial FLASH. Once the complete firmware image is in the serial FLASH and has been verified as good, a bootloader can be invoked to copy the new firmware image from the serial FLASH into the CC2530 FLASH memory. In addition the serial FLASH could be used for data storage depending on the application requirements.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 14 of 33 DEVELOPMENT TOOLS TI CC-DEBUGGER Custom firmware development can be done on the ProFLEX01-SOC module using development tools available thought TI. Shown in Figure 6 is a USB CC-DEBUGGER, which can be used both for debugging or programming. It plugs directly into the ProFLEX01-SOC Development Board (see Error! Reference source not found.), and can asily be adapted to other hardware. See the Texas Instruments website for more information. Figure 6 CC-DEBUGGER IAR Embedded Workbench for 8051 Also required is Embedded Workbench for 8051 from IAR Systems. IAR Embedded Workbench for 8051 is an Integrated Development Environment (IDE) for building and debugging embedded applications. Visit the IAR Systems website for additional information.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 15 of 33 ELECTRICAL SPECIFICATIONS The majority of these characteristics are based on the use of the TI 802.15.4 MAC loaded with the generic application firmware written by LSR. Custom firmware may require these values to be re-characterized by the customer. Absolute Maximum Ratings Parameter Min Max Unit Power supply voltage (VCC) -0.2 +3.6 V Voltage on any GPIO -0.2 VCC + 0.2 V RF input power, antenna port +10 dBm RF input power, transmit port +8 dBm Operating temperature -40 +85 ºC Storage temperature -40 +105 ºC Table 3 Absolute Maximum Ratings1 Recommended Operating Conditions Parameter Min Typ Max Unit Power supply voltage (VCC) 2.4 3.3 3.5 Vdc Input frequency 2405 2480 MHz Ambient temperature range -40 25 85 ºC Table 4 Recommended Operating Conditions Module will NOT transmit, if VCC > 3.55V. 1 Under no circumstances should exceeding the ratings specified in the Absolute Maximum Ratings section be allowed. Stressing the module beyond these limits may result permanent damage to the module that is not covered by the warranty.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 16 of 33 General Characteristics Parameter Min Typ Max Unit RF frequency range 2405 2480 MHz RF data rate 250 kbps Host data rate 1.2 19.2 921.6 kbps Flash memory 256 kBytes RAM 8 kBytes Table 5 General Characteristics Power Consumption Parameter Test Conditions Min Typ Max Unit Transmit mode 2440 MHz, 3.3V, +25°C, +20 dBm output, 50 Ω 130 160 195 mA Receive mode 2440 MHz, 3.3V, +25°C, - 50 dBm input 29 32 35 mA Sleep mode 3 8 uA Table 6 Power Consumption DC Characteristics – General Purpose I/O Parameter Test Conditions Min Typ Max Unit Logic input low VCC = 3.0V, +25°C .5 V Logic input high VCC = 3.0V, +25°C 2.5 V I/O-pin pullup and pulldown resistors VCC = 3.0V, +25°C 20 kΩ Logic output low (P1.0) VCC = 3.0V, +25°C, IOUT = 20mA .5 V Logic output low (ALL I/O except P1.0) VCC = 3.0V, +25°C, IOUT = 4mA .5 V Logic output high (P1.0) VCC = 3.0V, +25°C, IOUT = -20mA 2.4 V Logic output high (ALL I/O except P1.0) VCC = 3.0V, +25°C, IOUT = -4mA 2.4 V Table 7 DC Characteristics General Purpose I/O
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 17 of 33 RF Characteristics Nominal Transmitter Characteristics (TA = 25°C, VCC = 3.3V, fC = 2440 MHz, 50Ω) Parameter Test Conditions Min Typ Max Unit Minimum output power Min 802.15.4 MAC API Setting 7 9 11 dBm Maximum output power Max 802.15.4 MAC API Setting 18 20 22 dBm Programmable output power range 9.5 20 dBm Transmit current – min output Min 802.15.4 MAC API Setting 75 78 85 mA Transmit current – max output Max 802.15.4 MAC API Setting 130 160 195 mA Error vector magnitude 12 35 % Table 8 Nominal Transmitter RF Characteristics Minimum Transmitter Characteristics (TA = +85°C, VCC = 2.4V, fC = 2440 MHz, 50Ω) Parameter Test Conditions Min Typ Max Unit Minimum output power Min 802.15.4 MAC API Setting 2 4 6 dBm Maximum output power Max 802.15.4 MAC API Setting 16 17 19 dBm Programmable output power range 4 17 dBm Transmit current – min output Min 802.15.4 MAC API Setting 70 73 76 mA Transmit current – max output Max 802.15.4 MAC API Setting 120 129 145 mA Table 9 Minimum Transmitter RF Characteristics
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 18 of 33 Maximum Transmitter Characteristics (TA = -40°C, VCC = 3.6V, fC = 2440 MHz, 50Ω) Parameter Test Conditions Min Typ Max Unit Minimum output power Min 802.15.4 MAC API Setting 13 14 15 dBm Maximum output power Max 802.15.4 MAC API Setting 21 23 24 dBm Programmable output power range 14 23 dBm Transmit current – min output Min 802.15.4 MAC API Setting 80 87 95 mA Transmit current – max output Max 802.15.4 MAC API Setting 219 276 355 mA Table 10 Maximum Transmitter RF Characteristics RF Power Settings (TA = 25°C, VCC = 3.3V, fC = 2440 MHz, 50Ω) Radio TXPOWER Register Value RF Output Power Typical Current Consumption 0x65 8.8 dBm 77mA 0x75 10.4 dBm 81mA 0x85 11.8 dBm 86mA 0x95 13.0 dBm 90mA 0xA5 14.9 dBm 101mA 0xB5 16.5 dBm 112mA 0xD5 18.6 dBm 133mA 0xF5 21.1 dBm 179mA Table 11 RF Power Settings with LSR Host Software
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 19 of 33 Tables 10-12 below list the RF Power Limits per channel that must be maintained to assure compliance with FCC or ETSI. RF Channel Radio TXPOWER Register Value RF Output Power
26 Not used Not used
Table 12 RF Transmit Output Power Limits for FCC Compliance (Internal or External Antenna) RF Channel Radio TXPOWER Register Value RF Output Power Table 13 RF Transmit Output Power Limits for ETSI Compliance (Internal Antenna)
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 20 of 33 RF Channel Radio TXPOWER Register Value RF Output Power Table 14 RF Transmit Output Power Limits for ETSI Compliance (External Antenna) Receiver Characteristics (TA = 25°C, VCC = 3.3V, fC = 2440 MHz) Parameter Test Conditions Min Typ Max Unit Receiver sensitivity (1% PER) HGM -92 -97 -99 dBm Saturation (maximum input level) (1% PER) HGM -13 dBm Interference rejection Desired signal at - 82 dBm, 802.15.4 interferer ±5 MHz 47 dB ±10 MHz 54 dB ±20 MHz 57 dB Table 15 Receiver RF Characteristics For additional details regarding the electrical specifications, see the CC2530 and CC2591 datasheets on the TI website.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 21 of 33 SOLDERING RECOMMENDATIONS Recommended Reflow Profile for Lead Free Solder Note: The quality of solder joints on the castellations (‘half vias’) where they contact the host board should meet the appropriate IPC Specification . See IPC -A-610-D Acceptability of Electronic Assemblies, section 8.2.4 Castellated Terminations.”
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 22 of 33 CLEANING In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the RF shield, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. Ultrasonic cleaning could damage the module permanently. OPTICAL INSPECTION After soldering the Module to the host board, consider optical inspection to check the following: Proper alignment and centering of the module over the pads. Proper solder joints on all pads. Excessive solder or contacts to neighboring pads, or vias. REWORK The module can be unsoldered from the host board if the Moisture Sensitivity Level (MSL) requirements are met as described in this datasheet. Never attempt a rework on the module itself, e.g . replacing individual components. Such actions will terminate warranty coverage. SHIPPING, HANDLING, AND STORAGE Shipping Bulk orders of the ProFLEX01-SOC modules are delivered in trays of 25. Handling The ProFLEX01-SOC modules contain a highly sensitive electronic circuitry. Handling without proper ESD protection may destroy or damage the module permanently. Moisture Sensitivity Level (MSL) Per J-STD-020, devices rated as MSL 4 and not stored in a sealed bag with desiccant pack should be baked prior to use. Devices are packaged in a Moisture Barrier Bag with a desiccant pack and Humidity Indicator Card (HIC). Devices that will be subjected to reflow should reference the HIC and J-STD-033 to determine if baking is required. If baking is required, refer to J-STD-033 for bake procedure. Storage Per J-STD-033, the shelf life of devices in a Moisture Barrier Bag is 12 months at <40ºC and <90% room humidity (RH). Do not store in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX. Do not store in direct sunlight. The product should not be subject to excessive mechanical shock.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 23 of 33 Repeating Reflow Soldering Only a single reflow soldering process is encouraged for host boards.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 24 of 33 AGENCY STATEMENTS Agency Certifications FCC ID: TFB-PROFLEX1SOC IC ID: 5969A-PROFLEX1SOC ETSI: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION : Any changes or modifications not expressly ap proved by the party responsible for compliance could void the user's authority to operate this equipment.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 25 of 33 Industry Canada Statements Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the This device has been designed to operate with the antennas listed below, and having a maximum gain of 2.0 dB. Antennas not included in this list or having a gain greater than 2.0 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. LS Research 001 -0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector and LS Research 080 -0001 U.FL to Reverse Polarity SMA Bulkhead Cable (105mm in length) In addition to the antennas listed above, t he ProFLEX01-SOC module has also been certified with an integrated PCB F-antenna. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (e.i.r.p) ne dépasse pas celle admise pour une communication réussie. Cet appareil a été conçu pour fonctionner avec les antennes énumérées ci-dessous, et ayant un gain maximum de 2,0 dB. Antennes pas inclus dans cette liste ou ayant un gain supérieur à 2,0 dB sont strictement interdites pour une utilisation avec cet appareil. L'impédance d'antenne requise est de 50 ohms. LS Research 001-0001 2.4 GHz Antenne dipôle avec inversion de polarité Connecteur SMA et LS Research 080- 0001 U.FL àinversion de polarité SMA traversée de câble (105 mm de longueur) En plus des antennes énumérées ci-dessus, le module ProFLEX01-SOC a également été certifié par un PCB integer F-antenne.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 26 of 33 OEM Responsibilities to comply with FCC and Industry Canada Regulations The ProFLEX01-SOC Module has been certified for integration into products only by OEM integrators under the following conditions: This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co- location with another transmitter), then t he FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re -evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. Le module ProFLEX01-SOC a été certifiée pour l'intégration dans les produits que par les intégrateurs OEM dans les conditions suivantes: Ce dispositif est accordé pour une utilisation dans des configurations mobiles seule dans laquelle les antennes utilisées pour cet émetteur doit être installé pour fournir une distance de séparation d'au moins 20cm de toute personne et ne pas être co-localisés avec les autres émetteurs, sauf en conformité avec FCC et Industrie Canada, multi-émetteur procédures produit. Tant que les deux conditions précitées sont réunies, les tests de transmetteurs supplémentaires ne seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformité supplémentaires requis avec ce module installé (par exemple, les émissions appareil numérique, les exigences de périphériques PC, etc.) NOTE IMPORTANTE: Dans le cas où ces conditions ne p euvent être satisfaites (pour certaines configurations ou de co -implantation avec un autre émetteur), puis la FCC et Industrie autorisations Canada ne sont plus considérés comme valides et l'ID de la FCC et IC numéro de certification ne peut pas être utilisé sur la produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 27 of 33 End Product Labelling The ProFLEX01-SOC Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: TFB-PROFLEX1SOC” “Contains Transmitter Module IC: 5969A-PROFLEX1SOC” or “Contains FCC ID: TFB-PROFLEX1SOC” “Contains IC: 5969A-PROFLEX1SOC” The OEM of the ProFLEX01-SOC Module must only use the approved antenna(s) listed above, which have been certified with this module. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. The user manual for the end product must include the following information in a prominent location: This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi- transmitter product procedures.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 28 of 33 Le ProFLEX01-SOC Module est étiqueté avec sa propre ID de la FCC et IC numéro de certification. Si l'ID de la FCC et IC numéro de certification ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, puis l'extérieur de l'appareil dans lequel le module est installé doit également afficher une étiquette mentionnant le module ci-joint. Dans ce cas, le produit final doivent être étiquetés dans un endroit visible de ce qui suit: Module émetteur Contient FCC ID: TFB-PROFLEX1SOC Module émetteur Contient IC: 5969A-PROFLEX1SOC ou Contient FCC ID: TFB-PROFLEX1SOC Contient IC: 5969A-PROFLEX1SOC Le constructeur d'équipements de l'ProFLEX01-SOC module ne doit utiliser l'antenne approuvée (s) ci-dessus, qui ont été certifiés avec ce module. L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF ou RF changer les paramètres liés au mode d'emploi du produit final. Le manuel d'utilisation pour le produit final doit comporter les informations suivantes dans un endroit bien en vue: Ce dispositif est accordé pour une utilisation dans des configurations mobiles seule dans laquelle les antennes utilisées pour cet émetteur doit être installé pour fournir une distance de séparation d'au moins 20cm de toute personne et ne pas être co-localisés avec les autres émetteurs, sauf en conformité avec FCC et Industrie Canada, multi- émetteur procedures produit.
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 29 of 33 MECHANICAL DATA PCB Footprint Notes: 1) Optional alignment holes are for use with fixture placement and hand soldering operations. 2) See http://wiki.lsr.com for additional information. Figure 7 PCB footprint
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 30 of 33 General Module Dimensions Figure 8 Basic dimensions
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 31 of 33 COMPATIBILITY To maintain compatibility with other ModFLEX™ family transceiver modules it is important to use the module pins in your application as they are designated in Figure 9. Since the available GPIO and peripherals vary per micro, not all pins may be populated. All attempts are made to lay out modules starting with the lowest number in the peripheral (ADC, TMR/PWM, GPIO) series. For example if there are only two ADC’s available they will be brought out to ADC1 and ADC2 (module pins 20 and 21). GND 1 ModFLEX™ Generic Module Footprint
69 GND
JTAG - TMS 9 61 SPI - MOSI JTAG - TDI 10 60 SPI - MISO JTAG - TCK 11 59 SPI - SCK JTAG - TDO 12 58 SPI - SS JTAG/PDI/JRST 13 57 IIC - SDA nReset 14 56 IIC - SCL Analog REF 15 55 GPIO 16 Analog REF 16 54 GPIO 15 CMP+ 17 53 GPIO 14 CMP- 18 52 GPIO 13 CMPOUT 19 51 GPIO 12 ADC1 20 50 GPIO 11 ADC2 21 49 GPIO 10 ADC3 22 48 GPIO 9 ADC4 23 47 GPIO 8 ADC5 24 46 GPIO 7 ADC6 25 45 GPIO 6 VCC - 3V3DC 26 44 GND 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 TMR/PWM 1 TMR/PWM 2 TMR/PWM 3 TMR/PWM 4 TMR/PWM 5 TMR/PWM 6 TMR/PWM 7 TMR/PWM 8 UART - TX UART - RX UART - CTS UART - RTS GPIO 1 GPIO 2 GPIO 3 GPIO 4 GPIO 5 Figure 9 ModFLEX™ Generic Module Footprint
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 32 of 33 MODULE REVISION HISTORY Rev 1 Initial production release. LS RESEARCH MAC ID: 00:25:CA:03:XX:XX:XX:XX 00:25:CA:07:XX:XX:XX = MAC ID 2D Barcode Format is Data Matrix Standard XX:XX:XX:XX = unique portion of MAC ID that changes for each module Wireless Product Development M/N: ProFLEX01-SOC P/N: 450-0035 REV 1 2D Bar Code FCC ID: TFB-PROFLEX1SOC IC: 5969A-PROFLEX1SOC RoHS Part Number: 450-0035 F Antenna Module LS RESEARCH MAC ID: 00:25:CA:03:XX:XX:XX:XX 00:25:CA:07:XX:XX:XX = MAC ID 2D Barcode Format is Data Matrix Standard XX:XX:XX:XX = unique portion of MAC ID that changes for each module Wireless Product Development M/N: ProFLEX01-SOC P/N: 450-0044 REV 1 2D Bar Code FCC ID: TFB-PROFLEX1SOC IC: 5969A-PROFLEX1SOC RoHS Part Number: 450-0044 U.FL Module
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET The information in this document is subject to change without notice. 330-0049-R1.1 Copyright © 2016 LSR Page 33 of 33 CONTACTING LSR Headquarters LSR W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website www.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSR’S TERMS AND CONDITIONS OF SALE LOCATED ON LSR’S WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE I MPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON -INFRINGEMENT. IN NO EVENT SHALL LSR BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or warranties with respect to the accuracy or co mpleteness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. LSR does not make any commitment to update the information contained herein. Unless specifically provi ded otherwise, LSR products are not suitable for, and shall not be used in, automotive applications. LSR’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.