0700461908906

WIPY3.0 PYCOM | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 24

Technical content

1.0 Overview

Introducing the WiPy 3.0. The tiny MicroPython enabled Wifi & Bluetooth IoT development platform. With a 1KM WiFi range, state of the art Espressif ESP32 chipset and dual processor, the WiPy 3.0 is all about taking the Internet of Things to the next level. Create and connect your things everywhere. Fast.

2.0 Features

– Powerful CPU, BLE and state of the art WiFi radio. 1KM Wifi Range – MicroPython enabled – Fits in a standard breadboard (with headers) – Ultra–low power usage: a fraction compared to other connected micro controllers – Available with or without pin headers soldered on Size 42mm x 20mm x 3.5mm (excluding headers) Operating temperature: –40 to 85 degrees celsius ESP32 Dual Core Microcontroller and WiFi/Bluetooth 4.2 radio 3V3 Ultra–Low–Noise switching regulator 8MB flash memory U.FL connector Reset switch RF switch High performance SMD antenna RGB heart beat LED

3.0 Specifications

3.1 CPU

– Xtensa® dual–core 32–bit LX6 microprocessor(s), up to 600 DMIPS – Hardware floating point acceleration – Python multi–threading – An extra ULP–coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep–sleep mode while only consuming ~25uA.

3.2 Memory

– RAM: 520KB + 4MB – External flash: 8MB

3.3 WiFi

– 802.11b/g/n 16mbps

3.4 Bluetooth

– Low energy and classic

3.5 RTC

– Running at 150kHz

3.6 Security

– SSL/TLS support – WPA Enterprise security

3.7 Hash / encryption

– SHA – MD5 – DES – AES

4.0 Block Diagram

Figure 1 – System block diagram

5.0 Pinout

Figure 2 – Module pinout diagram Note: The ESP32 supports remapping its peripherals to alternative pins. See below for a detailed list. FCC ID: 2AJMTWIPY3R IC: 22263-WIPY3RModel: WiPy3.0 WiFi Bluetooth Reset Button WS2812 LED WiFi / Bluetooth External Antenna Connector Pinout diagram GND 3V3 P10 RX0 TX0 TX1 RX1 PROGRAM Port SDA SCL P11 P12 CLK MOSI MISO P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 ADC2_6 ADC2_8 ADC2_9 ADC1_5 ADC1_4 ADC1_6 ADC1_7 ADC1_3 ADC1_2 ADC1_1 ADC1_0ADCPA ADCPA EMACTXD2 U0TXD U0CTS U0RTSVSPIWP VSPIHD MTCK MTDI VSPIQ VSPICS0 MTD0HSPICS0 HSPIWP HSPIQ HSPIID SDDATA2 SDDATA3 HS2DATA2 HS2DATA3 HSPIHD SDCMD SDDATA1 HS2CMD HS1DATA6 HS2DATA1 CLKOUT1RGB_LED CLKOUT3 CLKOUT2 U0RXD EMACRXD0 EMACRXD1 EMACTXCLK EMACRXD2 EMACTXER EMACRXD3 EMACRXCLK EMACRXDV EMACTXD0 EMACTXD3 EMACRXER EMACTXD1 EMACTXEN ADC2_1 ADC2_0 ADC2_3 ADC2_7 ADC2_2 ADC2_5 ADC2_4 RTCIO16 RTCIO6 RTCIO7 RTCIO8 RTCIO9 RTCIO4 RTCIO5 RTCIO3 RTCIO2 RTCIO1 RTCIO0 RTCIO11 RTCIO10 RTCIO13 RTCIO17 RTCIO12 RTCIO15 RTCIO14 Touch1 Touch0 Touch3 Touch6 MTMS HSPICLK SDCLK HS2CLK DAC_1 DAC_2 Touch8 Touch9Touch7 Touch2 Touch5 Touch4 ChipPURST GPIO3 GPIO1 GPIO0 GPIO4 GPIO15 GPIO5 GPIO27 GPIO19 GPIO2 GPIO12 GPIO13 GPIO22 GPIO21 GPIO14 GPIO25 GPIO26 GPIO33 GPIO32 GPIO34 GPIO35 GPIO39 GPIO38 GPIO37 GPIO36 XTAL32 XTAL32 VDET1 VDET2 SensVN SensCN SensCP SensVP Only Input pins! No pullup/pulldown internal resistance Absolute MAX per pin 12mA recommended 6mA! Power GND Serial Pin Analog Pin Control Physical Pin Port Pin Touch Pin DAC Pin PMW Pin Distributed and manufactured by Pycom Ltd. Registered office: High Point, 9 Sydenham Road, Guildford, Surrey GU1 3RX, UK Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this document may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Pycom Ltd, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law. T o order contact sales@pycom.io Low Level Bootloader P2 + GND Boot modes and safe boot P12 + 3V3 1-3 sec Safe boot, latest firmware is selected 4-6 sec Safe boot, previous user update selected 7-9 sec Safe boot, the factory firmware is selected Hack your WiPy Connect to a 10nF capacitor to enable T ouch Pin function SDDATA0 Vin (3.5-5.5V) Up to 1.2-A Maximum Load Capability. Output ONLY. 19/12/17 WiFi external / internal antenna selection control pin Model: WiPy3.0

6.0 Pin Details

Table 1 – Module pinout Module Pin ESP32 GPIO Pin Name Default Function ADC PWM RTC† Notes 1 – – Reset Active Low, connected to on–board button 2 3 P0 RX0 (Programming) Used by the bootloader and to program the module 3 1 P1 TX0 (Programming) Used by the bootloader and to program the module 4 0 P2 2* If tied to GND during boot the device will enter bootloader mode, connected to the on–board RGB LED 5 4 P3 TX1 2* 6 15 P4 RX1 2* JTAG MTD, SD card CMD 7 5 P5 8 27 P6 2* 9 19 P7 10 2 P8 2* SD card DAT0 11 12 P9 SDA 2* JTAG TDI 12 13 P10 SCL (I2C) / CLK (SPI) 2* JTAG TCK 13 22 P11 MOSI 14 21 P12 If tied to 3.3V during boot the device enters safe boot mode, JTAG MISO, External WiFi/BT antenna switch, Low = on–board, High = U.FL 15 36 P13 1 Input only 16 37 P14 MISO 1 Input only 17 38 P15 1 Input only 18 39 P16 1 Input only 19 35 P17 1 Input only 20 34 P18 1 Input only

Table 1 – Module pinout Module Pin ESP32 GPIO Pin Name Default Function ADC PWM RTC† Notes 21 32 P19 1 22 33 P20 1 23 26 P21 2* DAC 24 25 P22 2* DAC 25 14 P23 2* JTAG TMS, SD card SCLK 26 – – Regulated 3.3V supply Output only, do not feed 3.3V into this pin or you can damage the regulator 27 – – Ground 28 – – Voltage Input Accepts a voltage between 3.5V and 5.5V † The pins on the RTC power domain can be used during deep sleep, specifically GPIO pins will maintain their state while in deep sleep. * ADC2 is currently not supported in the micropython firmware

6.1 Remapping Pins

The ESP32 features comprehensive pin remapping functionality. This allows peripherals to be mapped onto almost any available GPIO pins. The above table merely shows the default assignments. For example, the default mapping has the SPI and I2C clocks overlapping, meaning both cannot be used simultaneously without remapping one to a different pin. For a detailed guide of what peripheral can be assigned to what pins please read “Appendix A – ESP32 Pin Lists” of the ESP32 datasheet.

7.0 ESP32 Peripherals

Table 2 – Peripherals † These are hardware limits, the micropython firmware may impose its own limits. * Requires an external CAN bus transceiver, we recommend the SN65HVD230 from Texas Instruments. Figure 3 – External RTC crystal circuits For a more detailed description of the ESP32 peripherals along with peripherals not currently supported by our firmware, please check the ESP32 datasheet.

7.1 RTC

Our modules by default all use the internal RC oscillator at 150kHz for the RTC. If you require better accuracy/ stability you can connect a 32.768 kHz crystal (or TCXO) externally on pins P19 and P20 (or P19 for a TXCO) Peripheral Count Pins UART 3 Remappable to any GPIO. Up to 5 Mbps†. Note: P13–18 can only be mapped to RX or CTS since they are input only. I2C 2 Remappable to any GPIO except P13–18 since they are input only and I2C is bi–directional. Up to 5 MHz, constrained by pull–up strength†. SPI 3 Remappable to any GPIO. Up to 50 MHz†. Note: P13–18 can only be mapped to MISO since they are input only. CAN* 1 Remappable to any GPIO. Up to 1000Kbps† Note: P13–18 can only be mapped to RX since they are input only. JTAG 1 TDO = P4, TDI = P9, TCK = P10, TMS = P24 PWM 1 All GPIO except P13–18 which are input only ADC 18 Fixed mapping, see Table 1, Only ADC 1 is supported in our micropython firmware. DAC 2 Only available on P21 and P22 SD 1 DAT0 = P8, SCLK = P23, CMD = P4

8.0 Programming the device

8.1 UART

By default, the modules run an interactive python REPL on UART0 which is connected to P0 (RX) and P1 (TX) running at 115200 baud. The easiest way to connect to the WiPy is via our expansion board, but any USB UART adapter will suffice. Code can be run via this interactive REPL or you can use our PyMakr plugin for Atom or Visual Studio Code to upload code to the board.

8.2 Wi–Fi

By default, the WiPy also acts as a Wi–Fi access point. SSID: wipy–wlan–XXXX Password: www.pycom.io Once connected to the WiPy’s Wi–Fi network you can access it in two ways.

8.2.1 Telnet

Running on port 23 is a telnet server. This acts in a very similar way to the UART. It presents you with an interactive REPL and can also be used to upload code via PyMakr.

8.2.2 FTP

The WiPy also runs a FTP server that allows you to copy files to and from the device, include an SD card if one is connected. To connect to this FTP server, you need to use plain FTP (un–encrypted) with the following credentials: User: micro Password: python

9.0 Boot modes

9.1 Bootloader mode

In order to update the firmware of the WiPy device, it needs to be placed into bootloader mode. In order to do this, P2 needs to be connected to ground when the device reboots. Once in bootloader mode you can use the Pycom firmware update tool to update to the latest official firmware. If you are developing your own firmware based on our open–source firmware, a flashing script is provided with the source code.

9.2 Safe boot

The micropython firmware features a safe boot feature that skips the boot.py and main.py scripts and goes straight to the REPL. This is useful if the device is programmed with code that causes the device to crash or become inaccessible. To access this mode, you need to connect P12 to 3.3V and reset the device. Upon entering safe boot mode, the on–board LED will begin to blink orange. Depending on the duration the pin is held at 3.3V, a different firmware will be run. Table 3 – Boot modes 0–3 Seconds 3–6 Seconds Current firmware without running boot.py or main.py Previous firmware if the firmware was uploaded via OTA (without running boot.py and main.py)

10.1 Current consumption by power modes/features running at 5V

10.0 Power

The WiPy features an on–board voltage regulator that takes 3.5V – 5.5V from the VIN pin and regulates it to 3.3V. It is important to only use the 3.3V as an output and not try to feed 3.3V into this pin as this could damage the regulator. Table 4 – Power consumption by feature † More details can be found in section 14.2 Mode Min Avg. Max Units Idle (no radios) – 27.9 – mA WiFi AP – 97.4 – mA WiFi client – 108 – mA Bluetooth – 92.8 – mA Deep sleep – 19.7 – μA

11.0 Memory Map

11.1 Flash

11.2 RAM

11.3 ROM and eFuses

Table 5 – Flash memory map Table 6 – RAM memory map Table 7 – Miscellaneous memory Name Description Start address Size NVS Non–volatile RAM area. Used by the NVS API 0x9000 0x7000 Firmware Slot 0 First firmware slot. Factory firmware is flashed here 0x10000 0x180000 OTA info Information about the current active firmware 0x190000 0x1000 Firmware Slot 1 Second firmware slot 0x1A0000 0x180000 File system 504KB file system on devices with 4MB flash 0x380000 0x7F000 Config Config area for LoRa, Sigfox and LTE 0x3FF000 0x1000 File system (2) 4MB file system on devices with 8MB flash 0x400000 0x400000 Name Description Size On–chip SRAM Internal RAM memory used by the 2 xtensa CPUs 520KB Fast RTC RAM Fast RAM area accessible by the xtensa cores during boot and sleep modes 8KB Slow RTC RAM Slow RAM area accessible by the Ultra–Low Power Coprocessor during deep sleep 8KB External pSRAM External QSPI RAM memory clocked @ 40MHz 4MB Name Description Size On–chip ROM Contains core functions and boot code. 448KB eFuse 256 bits are used for the system (MAC address and chip configuration) and the remaining 768 bits are reserved for customer applications, including Flash– Encryption and Chip–ID 1kbit

12.0 WiFi

12.1 Supported features

– 802.11 b/g/n/e/i – 802.11 n (2.4 GHz), up to 150 Mbps – 802.11 e: QoS for wireless multimedia technology – WMM–PS, UAPSD – A–MPDU and A–MSDU aggregation – Block ACK – Fragmentation and defragmentation – Automatic Beacon monitoring/scanning – 802.11 i security features: pre–authentication and TSN – Wi–Fi Protected Access (WPA)/WPA2/WPA2– Enterprise/Wi–Fi Protected Setup (WPS) – Infrastructure BSS Station mode/SoftAP mode – Wi–Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management

12.2 Specifications

Table 8 – WiFi specifications Description Min Typ. Max Unit Input Frequency 2412 – 2484 MHz Tx power Output power of PA for 72.2 Mbps 13 14 15 dBm Output power of PA for 11b mode 19.5 20 20.5 dBm Sensitivity DSSS, 1Mbps – – 98 dBm CCK, 11 Mbps – – 91 dBm OFDM, 6 Mbps – – 93 dBm OFDM, 54 Mbps – – 75 dBm HT20, MCS0 – – 93 dBm HT20, MCS7 – – 73 dBm HT40, MCS0 – – 90 dBm HT40, MCS7 – – 70 dBm MCS32 – – 89 dBm Adjacent channel rejection OFDM, 6 Mbps – 37 – dB OFDM, 54 Mbps – 21 – dB HT20, MCS0 – 37 – dB HT20, MCS7 – 20 – dB

13.0 Bluetooth

13.1 Supported features

– Compliant with Bluetooth v4.2 BR/EDR and BLE specification – Class–1, class–2 and class–3 transmitter without external power amplifier – Enhanced power control – +12 dBm transmitting power – NZIF receiver with –97 dBm sensitivity – Adaptive Frequency Hopping (AFH) – Standard HCI based on SDIO/SPI/UART – High–speed UART HCI, up to 4 Mbps – BT 4.2 controller and host stack – Service Discover Protocol (SDP) – General Access Profile (GAP) – Security Manage Protocol (SMP) – ATT/GATT – HID – All GATT–based profile supported – SPP–like GATT–based profile – BLE Beacon – A2DP/AVRCP/SPP, HSP/HFP, RFCOMM – CVSD and SBC for audio codec – Bluetooth Piconet and Scatternet

13.2 Specification

13.2.1 Receiver – Basic Data Rate

Table 9 – Receiver (basic data rate) specifications Parameter Min Typ. Max Unit Sensitivity @0.1% BER – –94 – dBm Maximum received signal @0.1% BER 0 – – dBm Co–channel C/I – +7 – dB Adjacent channel selectivity C/I F = F0 + 1 MHz – – –6 dB F = F0 – 1 MHz – – –6 dB F = F0 + 2 MHz – – –25 dB F = F0 – 2 MHz – – –33 dB F = F0 + 3 MHz – – –25 dB F = F0 – 3 MHz – – –45 dB Out–of–band blocking performance 30Mhz ~ 2000MHz –10 – – dBm 2000MHz ~ 2400MHz –27 – – dBm 2500MHz ~ 3000MHz –27 – – dBm 3000MHz ~ 12.5GHz –10 – – dBm Intermodulation –36 – – dBm

Table 10 – Receiver (basic data rate) specifications

13.2.2 Receiver – Enhanced Data Rate

Parameter Min Typ. Max Unit π/4 DQPSK Sensitivity @0.1% BER – –90 – dBm Maximum received signal @0.1% BER – 0 – dBm Co–channel C/I – 11 – dB Adjacent channel selectivity C/I F = F0 + 1 MHz – –7 – dB F = F0 – 1 MHz – –7 – dB F = F0 + 2 MHz – –25 – dB F = F0 – 2 MHz – –35 – dB F = F0 + 3 MHz – –25 – dB F = F0 – 3 MHz – –45 – dB 8DPSK Sensitivity @0.1% BER – –84 – dBm Maximum received signal @0.1% BER – –5 – dBm C/I c–channel – 18 – dB Adjacent channel selectivity C/I F = F0 + 1 MHz – 2 – dB F = F0 – 1 MHz – 2 – dB F = F0 + 2 MHz – –25 – dB F = F0 – 2 MHz – –25 – dB F = F0 + 3 MHz – –25 – dB F = F0 – 3 MHz – –38 – dB

Table 11 – Receiver (BLE) specifications

13.2.3 Receiver – Bluetooth LE

Parameter Min Typ. Max Unit Sensitivity @30.8% PER – –97 – dBm Maximum received signal @30.8% PER 0 – – dBm Co–channel C/I – +10 – dB Adjacent channel selectivity C/I F = F0 + 1MHz – –5 – dB F = F0 – 1MHz – –5 – dB F = F0 + 2MHz – –25 – dB F = F0 – 2MHz – –35 – dB F = F0 + 3MHz – –35 – dB F = F0 – 3MHz – –45 – dB Out–of–band blocking performance 30MHz ~ 2000MHz –10 – – dB 2000MHz ~ 2400MHz –27 – – dBm 2500MHz ~ 3000MHz –27 – – dBm 3000MHz ~ 12.5GHZ –10 – – dBm Intermodulation –36 – – dBm

Table 12 – Transmitter (basic data rate) specifications

13.2.4 Transmitter – Basic Data Rate

Parameter Min Typ. Max Unit RF transmit power – 0 – dBm Gain control step – ±3 – dBm RF power control range –12 – +12 dBm +20 dB bandwidth – 0.9 – MHz Adjacent channel transmit power F = F0 + 1 MHz – –24 – dBm F = F0 – 1 MHz – –16.1 – dBm F = F0 + 2 MHz – –40.8 – dBm F = F0 – 2 MHz – –35.6 – dBm F = F0 + 3 MHz – –45.7 – dBm F = F0 – 3 MHz – –40.2 – dBm F = F0 + >3 MHz – 45.6 – dBm F = F0 – >3 MHz – 44.6 – dBm Δf1avg – – 155 KHz Δf2max 133.7 KHz Δf2avg/Δf1avg – 0.92 – – ICFT – –7 – KHz Drift rate – 0.7 – KHz/50μs Drift (1 slot packet) – 6 – KHz Drift (5 slot packet) – 6 – KHz

Table 13 – Transmitter (enhanced data rate) specifications

13.2.5 Transmitter – Enhanced Data Rate

Parameter Min Typ. Max Unit RF transmit power – 0 – dBm Gain control step – ±3 – dBm RF power control range –12 – +12 dBm π/4 DQPSK max w0 – –0.72 – KHz π/4 DQPSK max wi – –6 – KHz π/4 DQPSK max |wi + w0| – –7.42 – KHz 8DPSK max w0 – 0.7 – KHz 8DPSK max wi – –9.6 – KHz 8DPSK max |wi + w0| –10 KHz π/4 DQPSK modulation accuracy RMS DEVM – 4.28 – % 99% DEVM – – 30 % Peak DEVM – 13.3 – %

8 DPSK modulation accuracy

RMS DEVM – 5.8 – % 99% DEVM – 20 % Peak DEVM – 14 – % In–band spurious emissions F = F0 + 1MHz – –34 – dBm F = F0 – 1MHz – –40.2 – dBm F = F0 + 2MHz – –34 – dBm F = F0 – 2MHz – –36 – dBm F = F0 + 3MHz – –38 – dBm F = F0 – 3MHz – –40.3 – dBm F = F0 ± >3MHz – – –41.5 dBm EDR differential phase coding – 100 – %

Table 14 – Transmitter (BLE) specifications

13.2.6 Transmitter – Bluetooth LE

Parameter Min Typ. Max Unit RF transmit power – 0 – dBm Gain control step – ±3 – dBm RF power control range –12 – +12 dBm Adjacent channel transmit power F = F0 + 1MHz – –14.6 – dBm F = F0 – 1MHz – –12.7 – dBm F = F0 + 2MHz – –44.3 – dBm F = F0 – 2MHz – –38.7 – dBm F = F0 + 3MHz – –49.2 – dBm F = F0 – 3MHz – –44.7 – dBm F = F0 + >3MHz – –50 – dBm F = F0 – >3MHz – –50 – dBm Δf1avg – – 265 KHz Δf2max 247 – – KHz Δf2avg/Δf1avg – –0.92 – – ICFT – –10 – KHz Drift rate – 0.7 – KHz/50μs Drift – 2 – KHz

14.0 Electrical Characteristics

14.1 Absolute maximum ratings

14.2 Input/Output characteristics

Table 15 – Absolute maximum ratings Table 16 – Input/Output characteristics Parameter Symbol Min Typ. Max Unit Supply Input Voltage VIN 3.5 – 5.5 V Supply Output Current IOUT – – 1.2 A Supply Output Voltage V3V3 – 3.3 – V Storage Temperature TSTR – – – °C Operating Temperature TOPR –40 – 85 °C Moisture Sensitivity Level MSL – 1 – – Parameter Symbol Min Typ. Max Unit Input low voltage VIL –0.3 – 0.25×V3V3 V Input high voltage VIH 0.75×V3V3 – V3V3+0.3 V Max Input sink current ISINK – 6 12 mA Input leakage current IIL – – 50 nA Input pin capacitance Cpin – – 2 pF Output low voltage VOL 0.1×V3V3 – – V Output high voltage VOH 0.8×V3V3 – – V Max Output source current ISOURCE – 6 12 mA

15.0 Minimum Recommended Circuit

Figure 4 – Minimum required circuit

16.0 Mechanical Specifications

Figure 5 – Mechanical drawing (top down view) – Units: mm Figure 6 – Mechanical drawing (side view) – Units: mm

17.0 Recommended Land Patterns

17.1 Through hole

17.2 Surface mount (WiPy without headers only)

Figure 7 – Recommended land pattern (through hole) – Units: mm Figure 8 – Recommended land pattern (surface mount) – Units: mm

The above profile is based on Alpha CVP–390 solder paste, which has been successfully tested with our devices. Table 17 – Soldering profile temperatures Stage Duration/Rate Temperature Ramp to soak 2°C/s Ambient – 185°C Soak 60s 185°C Ramp to peak 1°C/s 240°C Reflow 45s >225°C Cool down 2°C/s

18.0 Soldering Profile

18.1 With headers

This device is not recommended for reflow soldering. The plastic of the pin headers will melt, instead please hand solder the module or use sockets.

18.2 Without headers

Figure 9 – Reflow soldering temperature profile

20.0 Packaging

19.0 Ordering Information

Table 18 – Ordering information Figure 10 – Mechanical drawing of packaging – Units: mm The module will come inside a reusable anti–static bag. If the module has headers it will also be inserted into anti–static foam. Total weight inc. packaging (with headers): 29g Total weight inc. packaging (without headers): 26g For more product accessories like expansion board or cases visit our website: http://www.pycom.io Bundle Contents FiPy Multi–Pack 1x WiPy 3.0 1x Expansion Board or Pysense or Pytrack 1x External WiFi antenna Available in quantities of 1, 2 or 5 Product EAN Description 0700461908906 WiPy 3.0 with Headers 0700461908388 WiPy 3.0 without headers

0700461341680 External WiFi Antenna

0700461341697 IP67 Antenna Pigtail

21.0 Certification

IC 22263–WIPY3R CE 0700 Copies of the certificates can be found on our website.

22.0 Regulator Information

22.1 EU Regulatory Conformance

Hereby, Pycom Ltd declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC

22.2 Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

22.2.1 RF Warning Statement

To comply with FCC RF exposure compliance requirements, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co–located or operating in conjunction with any other antenna or transmitter.

22.2.2 OEM integrator conditions

This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co–located with any other transmitter or antenna. As long as the two conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end–product for any additional compliance requirements required with this module installed. To ensure compliance with all non–transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. The module is limited to OEM installation ONLY. The module is limited to installation in mobile or fixed application. We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event that they require assistance for ensuring compliance with the Part 15 Subpart B requirements.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co–location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re– evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

22.2.3 End Product Labelling

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following: “Contains FCC ID: 2AJMTWIPY3R”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met. The following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference and 2. this device must accept any interference received, including interference that may cause undesired operation.

22.2.4 Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. In the user manual of the end product, the end user has to beinformed that the equipment complies with FCC radio– frequency exposure guidelines set forth for an uncontrolled environment. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. The end user manual shall include all required regulatory information/warning as show in this manual. The maximum operating ambient temperature of the equipment declared by the manufacturer is –40~+85C Receiver category 3

23.0 Revision History

Table 19 – Document revision history Version 1.0 Initial Release