DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 15

Technical content

THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC. 050-315 PRODUCT BRIEF

100 MBPS-5 GBPS

PRINTED CIRCUIT BOARD (PCB) MOUNT TRANSCEIVER 850NM VCSEL TRANSMITTER, PIN TIA RECEIVER SMALL & COMPACT WITH RUGGED CONSTRUCTION FOR HARSH ENVIRONMENTS REV DESCRIPTION DATE APPROVED A Initial Release 1/16/2015 SZ B Per DCN53850 2/6/2015 SZ C Per DCN55452 (revised Samtec connector part numbers) 05/28/15 TC

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 2 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V PCB Mount Fiber Optic Transceiver, 100M-5Gbps, MMF, 3.3V Glenair 050-315, is a ruggedized harsh environment PCB Mount Transceiver with electrical and optical functionality equivalent to SFP transceivers but with mechanical design that is suited to the harsh temperature and vibration environments found in the Military, Aerospace, Railway, Oil and Gas, and Industrial applications . The PCB mount optical transceivers also support optional Digital Monitoring Interface (DMI) features in accordance with SFF 8472. The transceiver is comprised of a transmitter section and a receiver section that resides on a common package and interface with a host board through a high speed electrical connector. The transmitter section includes the Transmitter Optical Subassembly (TOSA) and laser driver circuitry. The TOSA, containing an 850 nm VCSEL (Vertical Cavity Surface Emitting Laser) light source, is located at the optical interface and mates with the GC optical connector. The TOSA is driven by a laser driver, which converts differential logic signals into an analog laser diode drive current. This laser driver circuit regulates the optical power at a constant level provided the data pattern is DC balanced (for example 8B10B encoding). The receiver section includes the Receiver Optical Subassembly (ROSA) and amplification/quantization circuitry. The ROSA, containing a PIN photodiode and trans - impedance preamplifier, is located at the optical interface and mates with the GC optical connector. The ROSA is mated to a limiting amplifier IC that provides post- amplification and quantization. Also included is a Loss Of Signal (LOS) detection circuit. HOW TO ORDER Table 1 Part Number Options Part Number Description 050-315-1 100Mbps-2.5Gbps, without DMI 050-315-1-D 100Mbps-2.5Gbps, with DMI 050-315-1-D-ET1 100Mbps-2.5Gbps, with DMI, Extended Temperature Range 1 050-315-2 2.5Gbps-5Gbps, without DMI 050-315-2-D 2.5Gbps-5Gbps, with DMI 050-315-2-D-ET1 2.5Gbps-5Gbps, with DMI, Extended Temperature Range 1 KEY FEATURES/BENEFITS  SFP Compatible Electrical I/O signal levels  850nm VCSEL lasers to support up to 5 Gbps  PIN PD to support high sensitivity up to 5 Gbps  Industry standard CML input and outputs that make for simple integration on customer host PCB  Glenair Rugged GC Optical connector  High Operational Shock (650 g) & Vibration (54 g rms) – test reports available  Transceiver is securely mounted with screws to PCB to ensure excellent shock and vibration performance  High-Speed Electrical plug-in connector eliminates the need for soldering & enables ease of servicing  Captive screws to simplify manufacturing logistics and assembly  Small: Approx. 0.8” x 0.9” x 0.5”  -40°C to +85°C Operating Case Temperature o Extended Temperature Range Option  Glenair fiber jumpers connect from transceiver to any Glenair Mil/Aero Fiber Optic Connector Style  Evaluation fixtures available  Optional Digital Diagnostic and Monitoring (DMI) based on SFF-8472, enables monitoring of: o Transmitted optical power o Received optical power, o Laser bias current, o Temperature o Supply voltage

APPLICATIONS

 Harsh Environment such as: Airborne, Tactical, Railway, Industrial, Oil and Gas and Shipboard o Ethernet, FC 1x, 2x, 4x, SFPDP

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 3 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Ratings and Specifications Note 1: The motivation for the extended temperature range product option is to ensure that these devices will exhibit a graceful soft degradation in performance over the extended temperature range (Top_ET1). Continuous operation at case temperatures above 85C for extended period of time is not recommended as it could adversely affect long term reliability. TABLE 2 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Min Typ Max Units Notes Storage Temperature Ts -55 +100 °C Supply Voltage Vcc -0.4 3.8 V VccT & VccR may not differ by more than 0.5V TABLE 3 OPERATING CONDITIONS Parameter Symbol Min Typ Max Units Notes Operating Temperature, Case Top -40 +85 °C Standard Extended Operating Temperature, Case, Extended ET1 Top_ET1 +85 100 °C Note 1 Supply Voltage Vcc 3.135 3.3 3.465 V Supply Current Icc 180 200 mA Typical @ +85°C Power Supply Noise (Peak-Peak) Vcc_ripple 100 mV TABLE 4 ELECTRO-OPTICAL CHARACTERISTICS – TRANSMITTER ( TOP UNLESS NOTED OTHERWISE) Parameter Symbol Min Typ Max Units Notes Optical Output Power POUT -6.5 -5 -1 dBm 850nm VCSEL Optical Output Power in Extended Temp. Range POUT_ET1 -10 -8 -1 dBm Top_ET1 Extinction Ratio, 1.25Gbps Er 7 10 dB Exceeds OMA for GbE, 1FC Extinction Ratio, 2.125 Gbps & 4.25 Gbps Er 6 dB Exceeds OMA for 2FC & 4FC Extinction Ratio, Extended Temp Range Er_ET1 5 dB Top_ET1 Optical Wavelength λOUT 830 850 860 nm Optical Wavelength, Extended Temp Range λOUT_ET1 830 850 862 nm Top_ET1 Spectral Width, rms Δλ 0.85 nm Relative Intensity Noise RIN -117 dB/Hz Transmitter Differential Input Impedance Zin 100 Ohms AC coupled Internally Differential Input Voltage Vin_d 250 2200 mVp-p CML, 100 ohm

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 4 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Ratings and Specifications (continued) TABLE 5 ELECTRO-OPTICAL CHARACTERISTICS – RECEIVER ( TOP UNLESS NOTED OTHERWISE) Parameter Symbol Min Typ Max Units Notes 050-315-1 Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -22.5 -19 dBm PIN PD @ 1.25 Gbps Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -22.5 dBm PIN PD @ 2.5 Gbps 050-315-2 Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -18.5 dBm PIN PD @ 3.2 Gbps Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -18 dBm PIN PD @ 4.25Gbps Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -17.5 -16 dBm PIN PD @ 5 Gbps 050-315-1-D-ET1 Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -22.5 -19 dBm PIN PD @ 1.25 Gbps, Top_ET1 050-315-2-D-ET1 Sensitivity, BER 10-12, PRBS 2-7-1, Er 10 dB PIN -17.5 -16 dBm PIN PD @ 5 Gbps, Top_ET1 Overload, BER 10-12, PRBS 2-7-1 PIN -1 dBm @1.25Gbps or @ 5 Gbps Optical Wavelength λIN 770 870 nm Receiver Differential Output Impedance Zout 100 Ohms AC coupled internally Differential Output Voltage Swing Vout_d 600 1200 mV CML, 100 ohm LOS Assert Level LOS -24 -22 dBm @ 1.25Gbps LOS Hysteresis LOSHYS 1.25 2.3 dB @ 1.25Gbps TABLE 6 COMPLIANCE SPECIFICATIONS CHARACTERISTIC Standard Condition Notes Mechanical Shock MIL-STD-810 Para. 516.6, proc. I, 650g 0.9 ms operating Mechanical Vibration MIL-STD-810 Para. 514.6, 40g rms Random, operating ESD MIL-STD-883 1000V HBM Flame Resistance MIL-STD-1344 Method 1012, Cond. B 30 seconds Altitude Altitude, 25Kft Altitude, 70Kft Decompression Overpressure RTCA DO160 G Section 4.6.1 Category B1 Section 4.6.1 Category E1 Section 4.6.2 Category A2 Section 4.6.3 Category A1 Operating Altitude, 25,000 ft Operating Altitude, 70,000 ft Operating Altitude, 45,000 ft 28 psia Damp Heat RTCA DO160G MIL-STD-1344 Section 6 Category A Method 1002.2, Cond. B 48 hours, Non-operational 10 cycles, 24 hours, Operational Eye Safety CDRH and IEC-825 Class 1 Laser Product

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 5 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V FIGURE 1 - OUTLINE DRAWING CONTINUED (MARKING) LABELING: Each unit will be shipped in an antistatic bag. The label on the antistatic bag shall be at a minimum Arial size 10 black font and contain at a minimum the following information: ANTISTATIC BAG LABEL: Glenair Cage Code (06324) Part Number (PN 050-xxx as required) Date Code (DC xxxx) Serial Number (SN 123456) Each unit will be marked, either with a label or laser engraving, as follows:

  • Marking font to be Arial, greater than .08 inches in height.
  • Marking: FIRST LINE OF TEXT
  • Glenair
  • Serial Number (6 digits) SECOND LINE OF TEXT:
  • Part number Example GLENAIR SN123456 050-315-1-D-ET1

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 6 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V FUNCTIONAL DESCRIPTION TRANSMITTER SECTION Transmit Disable (Tx_Disable, pin 10) The transmitter section of the transceiver accepts a TTL and CMOS compatible transmit di sable control signal input that shuts down the transmitter optical output. A high signal disables the transmitter while a low signal allows normal transceiver operation. Also laser is disabled when TX Disable is open. In the event of a fault (e.g. eye safety circuit activated), cycling this control signal resets the module. Host systems should allow a 10ms interval between successive assertions of this control signal. Transmit Fault (Tx_Fault, Pin 2) A catastrophic laser fault will activate the transmitter signal, TX_FAULT, and disable the laser. This signal is an open collector output (pull-up required on the host board). A low signal indicates normal laser operation and a high signal indicates a fault. The TX_FAULT will be latched high when a laser fault occurs and is cleared by toggling the TX_DISABLE input or cycling the power of the transceiver. The transmitter fault condition can also be monitored via the 2- wire serial interface (address A2, byte 110, bit 2). Figure 2 PCB mount Transceiver Block Diagram

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 7 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Eye Safety Circuit The Transmitter section provides Class 1 eye safety by design and is compliant with US FDA CDRH AEL Class 1 and EN(IEC) 60825-1,2, EN60950 Class 1. The eye safety circuit continuously monitors optical output power levels and will disable the transmitter and assert a TX_FAULT signal upon detecting an unsafe condition. Such unsafe conditions can be created by inputs from the host board (Vcc fluctuation, unbalanced code) or faults within the module. RECEIVER SECTION Receiver Loss of Signal (LOS, Pin 20) The Loss Of Signal (LOS) output indicates an unusable optical input power level. The post-amplification IC includes transition detection circuitry which monitors the ac level of incoming optical signals and provides a TTL/CMOS compatible status signal to the host. A low LOS logic level indicates the presence of an optical input while a high LOS logic level indicates an unusable optical input. The LOS thresholds are factory-set so that a high output indicates a definite optical fault has occurred (e.g. failed transmitter, broken or disconnected fiber connection to the transceiver, etc.) . The LOS can also be monitored via the 2-wire serial interface (address A2h, byte 110, bit 1). FUNCTIONAL I/O The PCB Mount Transceiver accepts industry standard differential signals such as LVPECL and CML within the scope of the SFP MSA. To simplify board requirements, transmitter bias resistors and ac coupling capacitors are incorporated, per SFF-8074i, and hence are not required on the host board. The module is AC-coupled and internally terminated. Figure 3 illustrates a recommended interface circuit to link the PCB Mount Transceiver to the supporting Physical Layer integrated circuits. The PCB Mount Transceiver interfaces with the host circuit board through twenty I/O pins identified by function in T able 7. The transceiver high speed transmit and receive interfaces requires SFP MSA compliant signal lines on the host board. The Tx_Disable, Tx_Fault, and Rx_LOS lines require TTL lines on the host board (per SFF-8074i) if used. If an application chooses not to take advantage of the functionality of these pins, TX_Disable need to be tied to GND, TX_Fault and RX_LOS do not need to be connected. Digital Diagnostic Interface and Serial Identification (EEPROM) The PCB Mount Transceiver is compatible with the SFF-8074i SFP specification and with SFF-8472, the SFP specification for Digital Diagnostic Monitoring Interface. Both specifications can be found at http://www.sffcommittee.org.

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 8 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V FIGURE 3 RECOMMENDED PCB MOUNT TRANSCEIVER HOST BOARD SCHEMATIC The PCB Mount Transceiver features EEPROM for Serial ID, which contains the product data stored for retrieval by host equipment. This data is accessed via the 2-wire serial EEPROM protocol of the ATMEL AT24C01A or similar, in compliance with the industry standard SFP Multi-Source Agreement. The base EEPROM memory, bytes 0-255 at memory address 0xA0, is organized in compliance with SFF-8074i. The I2C accessible memory page address 0xB0 is reserved and used internally by SFP for the test and diagnostic purposes. As an enhancement to the conventional SFP interface defined in SFF-8074i, the PCB Mount Transceiver is compliant to SFF-8472 (digital diagnostic interface for optical transceivers). This new digital diagnostic information is stored in bytes 0- 255 at memory address 0xA2.Using the 2-wire serial interface defined in the MSA, the PCB Mount Transceiver provides real time temperature, supply voltage, laser bias current, laser average output power and received input power. These parameters are internally calibrated, per the SFF-8472 MSA. The digital diagnostic interface also adds the capability to

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 9 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V monitor for Transmitter Faults (TX_FAULT), and monitor for Receiver Loss of Signal (RX_LOS). The diagnostic information provides the opportunity for Predictive Failure Identification, Compliance Prediction, Fault Isolation and Component Monitoring. Predictive Failure Identification The predictive failure feature allows a host to identify potential link problems before system performance is impacted. Prior identification of link problems enables a host to service an application via “fail over” to a redundant link or replace a suspect device, maintaining system uptime in the process. For applications where ultra-high system uptime is required, the PCB Mount Transceiver provides a means to monitor two real-time laser metrics associated with observing laser degradation and predicting failure: average laser bias current (Tx_Bias) and average laser optical power (Tx_Power). Compliance Prediction Compliance prediction is the ability to determine if an optical transceiver is operating within its operating and environmental requirements. The PCB Mount Transceiver provide real-time access to transceiver internal supply voltage and temperature, allowing a host to identify potential component compliance issues. Received optical power is also available to assess compliance of fiber cable plant and remote transmitter. When operating out of requirements, the link cannot guarantee error free transmission. Fault Isolation The fault isolation feature allows a host to quickly pinpoint the location of a link failure, minimizing downtime. For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial to speeding service of an installation. PCB Mount Transceiver real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions. In addition, status flag Rx Loss of Signal (LOS) is mirrored in memory and available via the two-wire serial interface. Component Monitoring Component evaluation is another use of the PCB Mount Transceiver real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power. Potential uses are as debugging aids for system installation and design, and transceiver parametric evaluation for factory or field qualification. For example, temperature per module can be observed in high density applications to facilitate thermal evaluation of systems that incorporate this PCB Mount Transceiver Required Host Board Components A power supply noise rejection filter as describe in SFP MSA is required on the host PCB to meet data sheet performance. This is filter incorporates an inductor which should be rated to 400 mADC and 1 Ω series resistance or better. It should not be replaced with a ferrite. The required filter is illustrated in Figure 4. Also, the host PCB for the PCB Mount Transceiver requires 4.7 K to 10 KΩ pull-up resistors for TX_FAULT, LOS, SCA and SDL lines.

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 10 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V FIGURE 4 RECOMMENDED HOST BOARD POWER SUPPLY FILTERING CIRCUIT Fiber Compatibility The transceiver is capable of transmission at 2 to 550 meters with 50/125 μm fiber, and at 2 to 275 meters with 62.5 125 μm fiber, for 1.25 GBd Ethernet. It is capable of transmission up to 550m with 50/125 μm fiber and up to 300m with 62.5/125 μm fiber, for 1.0625 GBd Fiber Channel. Electrostatic Discharge (ESD) The Transceiver is compatible with ESD levels found in typical manufacturing and operating environments as described JEDEC EIA JESD22-A114, Class 1C (<2000Volts) HBM. Glenair recommends that devices are handled with ESD precautions to limit exposure to below 500V HBM. There are two design cases in which immunity to ESD damage is important. The first case is during handling of the transceiver prior to insertion to the host board. To protect the transceiver, it’s important to use standard industry ESD handling precautions. These precautions include using grounded wrist straps, work benches, and floor mats in ESD controlled areas. The ESD sensitivity of the Glenair PCB Mount Transceiver is compatible with typical industry production environments. The second case to consider is static discharges to the exterior of the host equipment after installation, in which case the transceiver may be subject to system-level ESD requirements.

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 11 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Application Support To assist in the transceiver design and evaluation process, Glenair offers the following aids:

  • Evaluation board & Product Manual, part number 050-329, which facilitates in the testing of the PCB Mount Transceiver.
  • 3D Step file to support modeling of mechanical fit and routing
  • PADS schematic and PCB layout library files that can be exported into customer’s PCB software design program
  • Applications Aid Example of PCB layout including details of high speed transmission designs Customer Manufacturing Processes This module is mounted with screws and interfaces with a high-speed low cost surface mount electrical connector residing on the host PC board. The PCB Mount Transceiver is not designed for aqueous wash, IR reflow, or wave soldering processes and should be mounted on the host board after host PC board has been through these processes. Proper torque values for mounting screws must be observed. Please contact Glenair for hardware mounting process recommendations.

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 12 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Byte Decimal Hex Data Notes Byte Decimal Hex Data Notes 0 80 Glenair PCB Mount Transceiver 37 00 Vendor OUI (NOT USED) 1 04 Serial ID Module Definition 38 00 Vendor OUI (NOT USED) 2 80 “GC” Fiber Optic Connector 39 00 Vendor OUI (NOT USED) 3 00 40 30 “0” Vendor Part Number ASCII character 4 00 41 35 “5” Vendor Part Number ASCII character 5 00 42 30 “0” Vendor Part Number ASCII character 6 01 1000BASE-SX 43 2D “-“ Vendor Part Number ASCII character 7 00 44 33 “3” Vendor Part Number ASCII character 8 00 45 31 “1” Vendor Part Number ASCII character 9 00 46 35 “5” Vendor Part Number ASCII character 10 00 47 2D “-“ Vendor Part Number ASCII character 11 01 Compatible with 8B/10B encoded data 48 32 “2” Vendor Part Number ASCII character 12 32 BR, 5Gbps 49 2D “-“ 13 00 50 44 “ D“ Vendor Part Number ASCII Character 14 00 51 2D “ -“ Vendor Part Number ASCII Character 15 00 52 45 “ E“ Vendor Part Number ASCII Character 16 37 550m of 50/125mm Fiber @ 1.25Gbps 53 54 “ T“ Vendor Part Number ASCII Character 17 1B 275 m of 62.5/125mm Fiber @ 1.25Gbps 54 31 “ 1“ Vendor Part Number ASCII Character 18 00 55 20 Note 5 19 00 56 20 “ “ Vendor REV Level ASCII Character 20 47 “G” Vendor NAME ASCII Character 57 20 “ “ Vendor REV Level ASCII Character 21 4C “L” Vendor NAME ASCII Character 58 20 “ “ Vendor REV Level ASCII Character 22 45 “E” Vendor NAME ASCII Character 59 20 “ “ Vendor REV Level ASCII Character 23 4E “N” Vendor NAME ASCII Character 60 03 Hex Byte of Laser Wavelength (Note 6) 24 41 “A” Vendor NAME ASCII Character 61 52 Hex Byte of Laser Wavelength (Note 6) 25 49 “I” Vendor NAME ASCII Character 62 RESERVED 26 52 “R” Vendor NAME ASCII Character 63 Check sum code for ID fields 0-62 (Note 7) 27 20 “ “ Vendor NAME ASCII Character 64 00 28 20 “ “ Vendor NAME ASCII Character 65 1A Hardware TX_Disable, TX_Fault, & LOS 29 20 “ “ Vendor NAME ASCII Character 66 00 30 20 “ “ Vendor NAME ASCII Character 67 00 31 20 “ “ Vendor NAME ASCII Character 68-83 Serial Number, ASCII (Note 8) 32 20 “ “ Vendor NAME ASCII Character 84-91 Date Code (Note 9) 33 20 “ “ Vendor NAME ASCII Character 92 68 Diagnostic Monitoring Type 34 20 “ “ Vendor NAME ASCII Character 93 B0 Enhanced Options 35 20 “ “ Vendor NAME ASCII Character 94 05 SFF-8472 rev 11.0 36 00 95 Checksum for bytes 64-94 (Note 7) 96-255 00 Notes: 1. RESERVED. 2. RESERVED 3. RESERVED. 4. RESERVED. 5. Table 1, Part number options/extensions 6. Laser wavelength is represented in 16 unsigned bits. The hex representation of 850nm is 0352. 7. Addresses 63 and 95 are checksums calculated per SFF-8472 and SFF-8074, and stored prior to product shipment. 8. Addresses 68-83 specify the module’s ASCII serial number and will vary by unit. 9. Addresses 84-91 specify the module’s ASCII date code and will vary according to manufactured date-code. TABLE 8 TWO-WIRE INTERFACE ID: DATA FIELDS – ADDRESS A0h

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 13 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V Table 9 Two-Wire interface ID: Data Fields – Address A2h Byte # Decimal Data Notes Byte # Decimal Data Notes Byte # Decimal Data Notes

0 Temp H Alarm MSB (Note 1) 26 TX Pwr L Alarm MSB (Note 4) 104 Rx Pavg MSB (Note 5 )

1 Temp H Alarm LSB (Note 1) 27 TX Pwr L Alarm LSB (Note 4) 105 Rx Pavg LSB (Note 5)

2 Temp L Alarm MSB (Note 1) 28 TX Pwr H Warning MSB (Note 4) 106 Reserved

3 Temp L Alarm LSB (Note 1) 29 TX Pwr H Warning LSB (Note 4) 107 Reserved

4 Temp H Warning MSB (Note 1) 30 TX Pwr L Warning MSB (Note 4) 108 Reserved

5 Temp H Warning LSB (Note 1) 31 TX Pwr L Warning LSB (Note 4) 109 Reserved

6 Temp L Warning MSB (Note 1) 32 RX Pwr H Alarm MSB (Note 5) 110 Status/Control

7 Temp L Warning LSB (Note 1) 33 RX Pwr H Alarm LSB (Note 5) 111 Reserved

8 Vcc H Alarm MSB (Note 2) 34 RX Pwr L Alarm MSB (Note 5) 112 Flag Bits

9 Vcc H Alarm LSB (Note 2) 35 RX Pwr L Alarm LSB (Note 5) 113 Flag Bits

10 Vcc L Alarm MSB (Note 2) 36 RX Pwr H Warning MSB (Note 5) 114 Reserved

11 Vcc L Alarm LSB (Note 2) 37 RX Pwr H Warning LSB (Note 5) 115 Reserved

12 Vcc H Warning MSB (Note 2) 38 RX Pwr L Warning MSB (Note 5) 116 Flag Bits

13 Vcc H Warning LSB (Note 2) 39 RX Pwr L Warning LSB (Note 5) 117 Flag Bits

14 Vcc L Warning MSB (Note 2) 40-45 Reserved 118 Reserved

15 Vcc L Warning LSB (Note 2) 56-94 External Cal Constants (Note 4) 119 Reserved

16 Tx Bias H Alarm MSB (Note 3) 95 Checksum for bytes 0-94 120-122 Reserved

17 Tx Bias H Alarm LSB (Note 3) 96 Temperature MSB (Note 1) 123 Reserved

18 Tx Bias L Alarm MSB (Note 3) 97 Temperature LSB (Note 1) 124 Reserved

19 Tx Bias L Alarm LSB (Note 3) 98 Vcc MSB (Note 2) 125 Reserved

20 Tx Bias H Warning MSB (Note 3) 99 Vcc LSB (Note 2) 126 Reserved

21 Tx Bias H Warning LSB (Note 3) 100 TX Bias MSB (Note 3) 127 Reserved (Note 8)

22 Tx Bias L Warning MSB (Note 3) 101 TX Bias LSB (Note 3) 128-247 Customer Writable (Note 9)

23 Tx Bias L Warning LSB (Note 3) 102 TX Power MSB (Note 4) 248-255 Vendor Specific

24 TX Pwr H Alarm MSB (Note 4) 103 TX Power LSB (Note 4)

25 TX Pwr H Alarm LSB (Note 4)

Notes: 1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C. 2. Supply voltage (VCC) is decoded as a 16 bit unsigned integer in increments of 100 μV. 3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 μA. 4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW. 6. Bytes 55-94 are not intended for use but have been set to default values per SFF-8472. 7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment. 8. Byte 127 accepts a write but performs no action (reserved legacy byte). 9. Bytes 128-247 are write enabled (customer writable).

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 14 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V TABLE 10 TRANSCEIVER DIGITAL DIAGNOSTIC MONITOR CHARACTERISTICS (WHEN APPLICABLE) PARAMETER SYMBOL MIN. UNITS NOTES Transceiver Internal Temperature Accuracy TINT ±3.0 Temperature is measured internal to the transceiver and is valid from -40°C to +85 °C case temperature Transceiver Internal Supply Voltage accuracy VINT ±0.1 V Supply voltage is measured internal to the transceiver and can, with less accuracy, be correlated to the voltage at the Vcc pin. Valid over 3.3V ±5% Transmitter Laser DC Bias Current Accuracy IINT ±10 Transmitted Average Optical Output Power Accuracy PT ±3.0 dB Coupled into 50/125 mm MM fiber. Valid from -1dBm to -10dBm Received Average Optical Input Power Accuracy PR ±3.0 dB Coupled from 50/125 mm MM fiber Valid from -24 dBm to - 1 dBm

©2014 Glenair, Inc. REV: C US Cage Code 06324 Printed in USA GLENAIR, INC. ∙ 1211 AIR WAY ∙ GLENDALE, CA 91201-2497 ∙ TEL: 818-247-6000 ∙ FAX: 818-500-9912 www.glenair.com PAGE 15 of 15 E-mail: sales@glenair.com 050-315 Product Brief PCB Mount Transceiver 100 Mbps – 5 Gbps, MMF, 3.3V ACCESSORIES Fiber Optic Jumper Cables to support connection to Mil/Aerospace Connectors KEY FEATURES:

  • Jumper cable between Glenair Transceiver (end A) and Mil/Aero Connector termini (End B)
  • Offered with either Multimode or Single Mode fibers PCB Threaded Inserts, PN 059-0007 KEY FEATURES
  • Simplifies installation of PCB Mount Transceivers eliminating the need for washers and nuts
  • Existing Options to support PCB thickness from 0.03” to 0.92”
  • Can support thicker PCB if required EVALUATION Boards, PN 050-329 Include
  • Manual with test block diagram, schematic and Evaluation board PCBA
  • Multiple types of PCB Mount Transceiver modules supported by this evaluation board
  • 2 fiber optic cables FIGURE 5 Fiber Optic Jumper Cable Assembly (see separate Glenair sales drawing FA02454 for details)