03301011

5145167-4 TEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 106

Technical content

V-1www.hubbell-wiring.com Wiring Device-Kellems Section V Kellems® Wire Management Products Pulling Grips Strain Relief Grips Support Grips Liquidtight Conduit, Tubing and Fittings Index Product Page

www.hubbell-wiring.com V-2 Wiring Device-Kellems Support Grip Conduit Support Grip Overhead Pulling Grip Bus Drop Support Grip Support Grip Conduit Support Underground Pulling Grip Flexible Conduit Grip Strain Relief Grip Deluxe Cord Grip Support Grip Bus Drop Support Grip Flexible Conduit Grip Bus Drop Support Grip Deluxe Cord Grip Strain Relief Grip Underground Pulling Grip INDUSTRY INDUSTRY UTILITY UTILITY COMMERCIAL RESIDENTIAL Support Grip To help you fully visualize the variety of uses available to you through Hubbell-Kellems Mesh Grips, we have prepared this diagram of common applications. It follows the typical pattern of usage you would find traveling from utility to industrial, commercial and residential environments. Pulling Grips are instrumental in the installations of transmission lines, service lines and cabling for construction and maintenance. Support Grips provide holding management for indoor and outdoor permanent cable installations. Strain Relief Grips are most often used to provide maximum reliability and minimum maintenance in areas where cords on machinery or equipment is impacted by motion or vibration or at risk of damage from cable pullout. Beyond the electrical applications illustrated here, Hubbell-Kellems Mesh Grips can be used for wire management on radio and microwave communications towers, crane and hoist wire rope maintenance, elevator cable management and more. Wire Management Products Kellems® Wire Mesh Grips Diagram

www.hubbell-wiring.com Wiring Device-Kellems Support Grip Conduit Support Grip Overhead Pulling Grip Bus Drop Support Grip Support Grip Conduit Support Underground Pulling Grip Flexible Conduit Grip Strain Relief Grip Deluxe Cord Grip Support Grip Bus Drop Support Grip Flexible Conduit Grip Bus Drop Support Grip Deluxe Cord Grip Strain Relief Grip Underground Pulling Grip INDUSTRY INDUSTRY UTILITY UTILITY COMMERCIAL RESIDENTIAL Support Grip

www.hubbell-wiring.comV-4 Wiring Device-Kellems Kellems® Wire Management Products Quick Reference Selection Guide for Grip Applications Universal Eye Used to fasten around a structure or closed loop. Available on standard duty support and light or heavy duty service drop grips. See pages V-31 and V-35. Single Eye For single hook attachment of permanent indoor/outdoor cable. Available on heavy-duty, standard duty, and service drop grips. See pages V-28, V-32, and V-34. Heavy-Duty Rotating Eye For underground wiring and overhead heavy-duty pulling of service lines and new construction cable. See pages V-7 and V-8. Deluxe Cord Indoor or outdoor use where subject to moisture, splash, or washdown. Examples are enclosures, crane hoist and pendant drop stations, hand tools, pumps, and processing equipment. Available in straight, 90°, or 45° configurations. See pages V-58 to V-61. Single Offset Eye For offset hook attachment of permanent indoor/ outdoor cable. Available on standard duty and light-duty support grips. See page V-30. Light-Duty Flexible Eye For light industrial pulling of electrical cable and for underground and industrial plant wiring and re-wiring. See page V-12. Dust-Tight Strain Relief Indoor use only for wiring of electrical enclosures, machine tools, portable power tools, bus drop cable systems. See page V-63. Double Eye For double hook attachment of permanent indoor/ outdoor cable. Available on heavy- duty and standard duty grips. See pages V-29 and V-33. Heavy-Duty Flexible Eye For overhead transmission and distribution line stringing. See pages V-6, V-7, and V-9. Liquid-Tight, Flexible Metal Conduit Wiring of machine tools, electrical enclosures, motors, and systems subjected to vibration, flexure, motion, or strain. Available in straight, 90°, or 45° configurations. See pages V-66 to V-68. Slack Grips For removing underground cable and pulling slack in existing cable and new installations and when end of cable is not available. See pages V-10 and V-11. Splicing Grips Used as temporary splice for cable and wire rope, or as reinforcement to protect cables and hoses. See pages V-13 and V-14. Conduit Riser Grips Ideal for supporting electrical wires inside rigid conduit via a supporting ring. See pages V-38 to V-40. Hose Containment Grips Used on flexible hose lines to prevent violent whipping of hose in the event of failure at the fitting. See page V-55. Specifications are subject to change without notice. Support Grips Strain Relief Grips Support Grips Pulling Grips Other Specialty Grips Wide Range Bus Drop Used indoors for cable support where flexible cable connects electrical equipment to bus duct. Support air hose and water hose. See page V-36.

V-5www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Pulling Grips Overhead, Underground, Commercial Construction, Specialty Flexible or rotating eyes will mate easily with line stringing swivels for attachment to pulling lines; they have great strength for trouble free pulling jobs Shoulder protectors contain the cable inside the grip and smooth the passage of the grip over line stringing blocks or conduit bends; they protect the leading edge of the grip from abrasion The galvanized steel mesh grip provides strength for secure pulling jobs and a slim profile with little build-up; it has flexibility to follow cable path The multiweave styles available add strength for big pulling jobs and provide positive gripping power Endless weave allows easy installation onto cable. It has a snag-free low profile; designed to be a reusable tool

www.hubbell-wiring.comV-6 Wiring Device-Kellems DUA-PULL® Grips Diameter Range Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Eye B Diameter Inches (cm) Over Cable and Grip** Inches (cm) Color Code Catalog Number Conductor Inches (cm) Rope* Inches (cm) .19"-.37" (.48-.94) .25"-.65" (.63-1.65) 6,500 (28,912) 033271037 .38"-.62" (.97-1.57) .50"-.90" (1.27-2.29) 14,000 (62,272) 033271038 .63"-.87" (1.60-2.21) .75"-1.10" (1.90-2.79) 20,000 (88,960) 033271039 .88"-1.12" (2.24-2.84) 1.00"-1.50" (2.54-3.81) 30,600 (136,109) 033271040 1.13"-1.37" (2.87-3.48) 1.25"-1.70" (3.17-4.32) 46,800 (208,166) 033271041 1.38"-1.90" (3.51-4.38) 1.50"-2.10" (3.81-5.33) 66,500 (295,792) 033271042 Note: E = Eye length. M = Mesh length at nominal diameter. *For rope, select smallest size grip which meets required work load. **Add to cable or rope diameter. Kellems® Wire Management Products Overhead Pulling Grips Galvanized Steel DUA-PULL® Grips, Flexible Eye, Double Weave Mesh DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission line stringing applications. They have a dual function, not provided by any other grip, of working with both bare and insulated conductors and synthetic rope. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. DUA-PULL® Feed Tube For Use with DUA- PULL Grip Rope Diameter Inches (cm) Feed Tube Length Inches (cm) Catalog Number M B E

www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Overhead Multiple Strength Pulling Grips Flexible or Rotating Eye, Triple, Double, Single Weave, Galvanized Steel Multiple Strength Style Grips Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires, messenger strands, wire rope and insulated cables. Multiple Strength Grip-Rotating Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Rotating Eye Dia. Inches (cm) Color Code Catalog Number Note: E- Eye length M-Mesh length at nominal diameter. Multiple Strength Grip-Flexible Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Eye A Dia. Inches (cm) Color Code Catalog Number Note: E- Eye length. M-Mesh length at nominal diameter. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. M E M A E

www.hubbell-wiring.comV-8 Wiring Device-Kellems K-Type Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Rotating Eye Dia. Inches (cm) Catalog Number Short Standard Note: E- Eye length. M-Mesh length at nominal diameter. See page V-25 for multiple cables in a single pulling grip. Kellems® Wire Management Products Underground K-Type Pulling Grips Rotating Eye, Double Weave, Galvanized Steel K-Type Grips Kellems® Rotating Eye, K-Type Pulling Grips are made of high strength galvanized steel strand. All Grips feature double weave mesh for greater strength and added mesh contact on the table, to handle longer or heavier pulling jobs. The forged eye mates easily with a swivel or shackle. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. M E

V-9www.hubbell-wiring.com Wiring Device-Kellems T-Type Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Short Standard Note: E- Eye length. M-Mesh length at nominal diameter. See page V-25 for multiple cables in a single pulling grip. Kellems® Wire Management Products Underground T-Type Pulling Grips Flexible Eye, Double Weave, Galvanized Steel T-Type Grips Kellems® Flexible T-Type Pulling Grips are made of high strength galvanized steel strand. They feature double weave mesh for positive holding power in medium to heavy pulling jobs. The grip eye will easily attach to a swivel. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. M E

www.hubbell-wiring.comV-10 Wiring Device-Kellems Slack Grip-Closed Mesh, Offset Eye, Double Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Standard Note: E- Eye length. M-Mesh length at nominal diameter. See page V-25 for multiple cables in a single pulling grip. Kellems® Wire Management Products Special Purpose Pulling Grips Non-Conductive and Slack Pulling Non-Conductive Grips Kellems® Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available for pulling single cable or cable bundles. Their braided double weave design adds strength and positive holding power. Non-Conductive Grips, Single Eye, Double Weave, Non-Metallic Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) A Inches (cm) Color Code Catalog Number IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. Slack Pulling Grips Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is used when the cable end is accessible. When not accessible, there are split lace and split rod closing styles. All grips feature a single offset eye for easy attachment to a pulling line. M E M E A

V-11www.hubbell-wiring.com Wiring Device-Kellems Slack Grip-Split Mesh, Rawhide Lace Closing, Offset Eye, Double Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Standard Long Kellems® Wire Management Products Special Purpose Pulling Grips Slack Pulling Slack Pulling Grips Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is used when the cable end is accessible. When not accessible, there are split lace and split rod closing styles. All grips feature a single offset eye for easy attachment to a pulling line. Slack Grip-Split Mesh, Rod Closing, Offset Eye, Single Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Note: E- Eye length. M-Mesh length at nominal diameter. See page V-25 for multiple cables in a single pulling grip. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. M E M E

www.hubbell-wiring.comV-12 Wiring Device-Kellems Kellems® Wire Management Products Low Tension Pulling Grips Flexible Eye, Single Weave, Galvanized Steel Light Duty Grips Light Duty Grips are made of galvanized steel in a single weave construction. They feature a flexible eye for easy attachment to a pulling line. Junior Pulling Grips Junior Pulling Grips feature a strong galvanized steel, single weave mesh. A flexible eye easily attaches to a pulling line, snake or fish tape. Junior Pulling Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Model Catalog Number Junior Grip Kit contains 6 grips, one of each size above, except 03305011. 033051114 Note: E- Eye length. M-Mesh length at nominal diameter. *Not included in Junior Grip Kit, 033051114. Note: See page V-25 for multiple cables in a single pulling grip. See page V-26 for building wire selection chart. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26. M E M E 033051114 Light Duty Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Short Standard

V-13www.hubbell-wiring.com Wiring Device-Kellems Regular Wire Rope Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) Approx. Strength of Grip Feet (m) Catalog Number Kellems® Wire Management Products Wire Rope Splicing Grips Triple, Double, Single Weave, Galvanized Steel Kellems® Wire Rope Grips Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double and single weave for superior gripping ability. They are available with or without a rotating barrel which will help eliminate twist in the old rope from being transferred to the new rope. Rotating Wire Rope Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) Approx. Strength of Grip Feet (m) Barrel Dimensions Length. x O.D. In. (cm) Catalog Number IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26.

www.hubbell-wiring.comV-14 Wiring Device-Kellems Double Weave Tube Cable Diameter Range Inches (cm) .37"-.49" (.94-1.24) .50"-.61" (1.27-1.55) .62"-.74" (1.57-1.88) .75"-.99" (1.90-2.51) 1.00"-1.49" (2.54-3.78) Approx. Breaking Strength Lbs. (N) 3,500 (15,568) 3,500 (15,568) 4,400 (19,571) 7,50 0 (33,360) 10,000 (44,480) Mesh Length Inches (cm) Catalog Number 18" (45.72) 013041330 01304064 01304009 — — 24" (60.96) — 01304011 01304013 01304010 01304015 36" (91.44) — — 013041234 01304054 01304055 48" (121.92) — — — 01304017 01304029 72" (182.88) — — — 01304037 013041333 Kellems® Wire Management Products Cable Splicing Grips Double Weave, Galvanized Steel / Single Weave, Galvanized Steel Splicing Grips Splicing Grips are made of galvanized steel in double weave mesh construction. They are available in various lengths and sizes to suit most applications. Junior Splicing Grips, Single Weave Junior Splicing Grips are made of galvanized steel and are designed for use in very light duty and small splicing jobs. Junior Tube Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) Length @ Nom Diameter Inches (cm) Catalog Number IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26.

V-15www.hubbell-wiring.com Wiring Device-Kellems Punch-Lok® Bands Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose. Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope. When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release caused by tripping on obstructions. A conductor-to-conductor (double-socking) pulling operation is a good example: where two grips connect two conductors to form a temporary splice. Bands should be applied to the ends of the grips as illustrated herein. It is also common practice to tape over the banded tail area to assure smooth passage through the sheaves. The conductor should be installed in the grip up to the elbows of the aluminum shoulders in order to assure full and complete gripping action as illustrated above. Punch-Lok ® Bands Grip Banding Range Inches (cm) Band Width Inches (cm) Band Inside Diameter Inches (cm) Model Catalog Number Accessories Punch-Lok Tools Catalog Number P-1000 for use with ⁵⁄₈" width Banding tool. 20320048 P-38 for use with ³⁄₈" and ⁵⁄₈" width Banding tool for tight spaces. 20320047 Note: In all cases two Punch-Lok Bands should be double wrapped approximately one inch to two inches (2.54cm to 5.08cm) from the grip’s tail. Banding is required to ensure maximum reliability and guard against accidental release. Kellems® Wire Management Products Tools and Bands Pulling Grips Accessories Punch-Lok® is a registered trademark of Punch-Lok Inc. 20320054 20320048 20320047

www.hubbell-wiring.comV-16 Wiring Device-Kellems C B A F E G D 20308001A Stainless Steel Swivels Maximum Safe Working Load Lbs. (N) Dimensions in Inches (cm) Model Catalog NumberA B C D E F G 2,250 (10,000) ⁷⁄₈" (2.22) 2½" (6.35) 3³⁄₈" (8.57) ⁷⁄₁₆" (1.11) ³⁄₈" (0.95) ⁵⁄₁₆" (0.79) ³¹⁄₃₂" (2.46) A-13L 20308001A 5,000 (22,240) 1¼" (3.17) 3¹¹⁄₁₆" (9.37) 4¾" (12.06) 1⁷⁄₃₂" (1.35) 1⁷⁄₃₂" (1.35) ¹³⁄₃₂" (1.03) 1⁹⁄₃₂" (3.25) BB-13L 20308002A 9,000 (40,030) 1½" (3.81) 4¼" (10.79) 5⁵⁄₈" (14.29) ¹¹⁄₁₆" (1.75) 1⁹⁄₃₂" (1.51) (1.27) 1⁹⁄₁₆" (3.97) B-13L 20308003A 10,000 (44,480) 1⁵⁄₈" (4.13) 4½" (11.43) (15.24) (1.90) ¹¹⁄₁₆" (1.75) ⁵⁄₈" (1.59) 1²³⁄₃₂" (4.36) C-13L 20308004A 30,000 (133,440) 2³⁄₈" (6.03) 7⁵⁄₈" (19.37) 10" (25.40) 1³⁄₁₆" (3.02) 1¹⁄₃ ₂" (2.62) ⁷⁄₈" (2.22) 2²⁵⁄₃₂" ( 7.0 6) D-13L 20308005A Kellems® Wire Management Products Swivels Pulling Grips Accessories Stainless Steel Swivels Swivels are essential to the efficiency and safety of any high tension application. They are particularly important where continuous pulls develop higher and higher torque levels. Torque is intensified by the pull-resistance of the cable itself and the resistance of the high tension controlling equipment regulating line sag. Ball bearing swivels release torque and prevent it from reaching dangerous levels that can damage the cable and obstruct the lines. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-17 to V-26.

V-17www.hubbell-wiring.com Wiring Device-Kellems Pulling Grip Selection Chart Grip Style Application Page Number DUA-PULL®, flexible eye Extra high strength overhead transmission line stringing for bare or insulated conductor and synthetic rope. V-6 Multiple strength, flexible eye Normal overhead transmission and distribution line stringing for bare or insulated conductor. V-7 Multiple strength, rotating eye Normal overhead transmission and distribution line stringing for bare or insulated conductor. V-7 K-type grip, rotating eye Underground power cables and communication lines. Service lines into factories. V-8 T-type grip, flexible eye Underground power cables and communication lines. Service lines into factories. V-9 Non-conductive, flexible eye Pull insulated distribution cable into place. V-10 Slack pulling, closed mesh Remove underground cable. For pulling slack in final placement of new cable when end of cable is available. V-10 Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable rawhide lace closing when end of cable is not available. V-11 Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable rod closing when end of cable is not available, with rod closing for quick installation. V-11 Light duty, flexible eye Light pulling, underground electrical construction. Industrial plant wiring and rewiring jobs. V-12 Junior, flexible eye Connect bundled insulated building wire to a pulling tape. Pull wire through conduit. V-12 Regular and rotating wire rope Restring wire rope in cranes and oil rigs. V-13 Splicing Temporary splice for cable or wire rope. V-14 Pulling Grip Accessories Tools, bands, swivels. V-15, V-16 Fiber Optic Cable Pulling Grips Pull fiber optic cable into place overhead, underground or through duct and conduit. V-47, V-48, V-49 Kellems® Wire Management Products Technical Information Pulling Grips Kellems Pulling Grips are reusable tools for pulling electrical cable, bare conductor or rope. They are easy and fast to install, providing the user with a smooth, slim profile that allows for easy passage through ducts and conduit. Kellems Pulling Grips are made of the highest quality galvanized steel strand which assures the user of a long lasting grip. There is a Kellems Pulling Grip for every pulling job. 1. Pulling grips are to be installed by a qualified individual in accordance with all applicable national and local safety, electrical and rigging codes. 2. Ensure that the correct grip is selected for your specific needs. 3. Do not use a pulling grip for any application other than pulling cable. 4. Thoroughly examine the grip for damage. Do not use a damaged grip. 5. Ensure that the recommended work load of the grip is suitable for the application. Never use grips at their approximated rated breaking strength. A safety factor of 5 is recommended for pulling grips. 6. Do not alter grips in any way. For example, do not modify pulling eyes, shoulders, fittings or lugs. 7. Do not attach any type of pulling hardware to any point on the grip other than the pulling eye. The pulling eye is the only acceptable means of attachment to external hardware. 8. Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against accidental release of the grip. Accidental release can occur if an object contracts and pushes against the tail end of the mesh, thereby expanding and releasing its hold. Select The Correct Pulling Grip Each Kellems Grip is designed to work on a specific range of cable diameters. Step 1 Refer to the chart below to determine the style of grip best suited for your application. Step 2 Determine your cable outside diameter. Step 3 Find the grip size that encompasses your cable diameter. Step 4 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough. Refer to page V-18 for safety and working load factors. CAUTION: It is very important to comply with all of the following precautions. Failure to do so may result in property damage, personal injury or death.

www.hubbell-wiring.comV-18 Wiring Device-Kellems The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads. The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories. It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same. The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application. These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate. Where the conditions of the application are not well defined or known, or where risk of injury to persons or property is involved, a greater safety factor should be utilized. Under normal conditions, Kellems’ recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained and inspected by the user at a frequency appropriate for the use and condition of the grip. Kellems® Wire Management Products Technical Information Pulling Grips Safety And Working Load Factors For Wire Mesh Grips Examples Approx. Breaking Safety Max. Recommended Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027 Support Grips 1,610 (7,161) 10 161 (716) 02201018 The maximum recommended working load then is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances. It is the end-user’s decision to determine how much of a safety factor is acceptable for the application. The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric unit of weight (kilograms) the conversion factor is 9.808 newtons/kilogram. Pulling Grip Materials Material Features Product Group Galvanized steel wire • High strength • Pulling grips

• Not subject to continuous • Wire rope grips outside environment • Splicing grips Non-metallic strand • Superior flex life • Non-conductive pulling grips
• Non-conductive
• Corrosion resistant
• Moderate strength Approvals UL and CSA Certification is indicated on appropriate product catalog pages.

V-19www.hubbell-wiring.com Wiring Device-Kellems Overhead Pulling DUA-PULL® Grips DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission line stringing applications. They have a dual function of working with both bare and insulated conductors and synthetic rope, not provided by any other grip. Kellems’ patented two-over, two-under weave design gives exceptional strength and gripping ability by putting more steel mesh in contact with the cable or rope surfaces. THIS IS THE ONLY PULLING GRIP RECOMMENDED FOR USE ON SYNTHETIC ROPE. Application The DUA-PULL Grips are primarily used in overhead transmission line construction where loads and safety considerations require an extra high strength grip. They are most commonly used for attaching pulling lines to conductors, conductors to running boards and “double socking" for conductor-to-conductor connections. The DUA-PULL line accommodates ACSR, ACAR, all aluminum and copper conductors. Also, the grips accommodate ground wires, messenger strands, wire ropes and synthetic ropes. Benefits

• Made of high strength galvanized steel strand.
• Recommended for pulling bare or insulated conductor, wire rope and synthetic rope.
• DUA-PULL mesh design offers the greatest holding power for all pulling applications.
• Each grip size is color coded for fast and accurate identification and selection.
• Will mate with swivels. See page V-16. Feed Tubes The Kellems Feed Tube is used when assembling synthetic rope into the DUA-PULL Grip. It is required on the largest two sizes of DUA-PULL Grips. Feed Tubes are available for use on all size DUA-PULL Grips. Benefits
• Saves time, allowing fast, easy assembly.
• Can be reused if not damaged. Note: 1. Do not run grips or swivels over bullwheels while under tension. 2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail. Banding is required to ensure maximum reliability and guard against accidental release. See page V-15. 3. Double braided rope, such as 2-in-1 type, should be back spliced for approximately 2/3 of the mesh length for best gripping results. Grip size should be selected by diameter of back splice. Components Kellems® Wire Management Products Technical Information Pulling Grips Identification Sleeve Color Coded EyeEnd of Conductor or Rope Tail Bands Mesh Shoulder Protector

www.hubbell-wiring.comV-20 Wiring Device-Kellems Overhead Pulling Multiple Strength Grips Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires, messenger strands, wire rope and insulated cables. They are made of high strength galvanized steel strand and feature a multi-weave mesh construction of single, double and triple weave for firm holding power. Application Kellems Multiple Strength Grips are ideal for overhead transmission and distribution line stringing where moderate loading is anticipated. They are economical tools for attaching conductors to pulling lines and double socking for conductor-to- conductor connections. Rotating Eye Feature Multiple Strength Grips are available with a forged steel rotating eye which can be attached to a swivel. The forged eye is durable, compact and streamlined and will thread through blocks and sheaves without binding. The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when tension is relaxed. If constant swivel action is required, a swivel should be used. For swivel dimensions, see page V-16. For rotating eye dimensions, see page V-21. Flexible Eye Feature Multiple Strength Grips are also available with a flexible, patented wire rope eye. This compact eye will mate with a swivel, and pass through blocks and sheaves without binding. Benefits

• Economical, high strength pulling tool.
• Multi-weave construction provides greater strength and holding power.
• Endless Weave Grip end lies flat on the cable and will not snag. Note: 1. Do not run grips or swivels over bullwheels while under tension. 2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail. Banding is required to ensure maximum reliability and guard against accidental release. See page V-15. Components Kellems® Wire Management Products Technical Information Pulling Grips Forg ed Eye Flexible Eye (Patented) End of Conductor or Cable Tail Bands (Double Wrapped) Mesh Shoulder Protectors Color Coded

V-21www.hubbell-wiring.com Wiring Device-Kellems Underground Pulling K-Type and T-Type Grips K-Type Application Rotating Eye, K-Type Pulling Grips are specially designed for use in the installation of underground power cables, communication lines and service lines into factories, shopping centers, construction projects and general underground electrical construction. Rotating Eye Feature K-Type Grips come equipped with a forged steel rotating eye which can be attached to a swivel. The forged eye is durable, compact and streamlined, and will thread through blocks and sheaves without binding. The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when the tension is relaxed. If constant swivel action is required, a swivel should be used. For swivel dimensions, see page V-16. Benefits

• An economical tool for pulling cable.
• Safe, rugged and dependable.
• Equipped with a rotating eye for spin out of pulling torque after load release.
• Easily installed and removed. Rotating Eye Dimensions Rotating Eye Dimensions Inches (cm) A B C D F T-Type Kellems Flexible T-Type Pulling Grips are made of high strength galvanized steel strand. They feature double weave mesh for positive holding power in medium to heavy pulling jobs. The grip eye will easily attach to a swivel. Application T-Type Pulling Grips are used for the installation of underground power cables, communication lines and service lines into factories, construction projects and for general underground electrical construction. Available in two mesh lengths, short for medium pulls, and standard for general purpose pulling. Benefits
• Will pull a single cable or cable bundles.
• Patented flexible eye design provides flexibility to follow line of pull.
• A dependable, reusable pulling tool.
• Easily installed and removed.
• Mates easily with a swivel. See page V-16. Kellems® Wire Management Products Technical Information Pulling Grips F D A 3/16 R. 1/8 R. C B

www.hubbell-wiring.comV-22 Wiring Device-Kellems Special Purpose Grips Non-Conductive Pulling Grips Kellems Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available for pulling single cable or cable bundles. Their braided double weave design adds strength and positive holding power. Application Kellems Non-Conductive Pulling Grips were developed for use by utilities for pulling overhead distribution lines in close proximity to energized lines and hardware. Benefits

• Color coded for fast on-site selection.
• Extra flexibility for easy installation.
• Non-metallic mesh provides for safe pulls over “hot" areas.
• Pellethane jacketed aramid fiber mesh resists abrasion.
• Grips are corrosion resistant. Note: Taping is required to guard against accidental release and to insure maximum reliability. Apply vinyl plastic electrical tape starting 2" to 3" (5.08cm to 7.62cm) from the tail of the grip onto 2" to 3" (5.08cm to 7.62cm) of cable. Slack Pulling Grips Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is used when the cable end is accessible. When not, there are split lace and split rod closing styles. All grips feature single offset eye for easy attachment to a pulling line. Application Slack Grips are widely used in pulling slack for final placement of under ground cable after it has been pulled in. They are also used for removing cable. Standard mesh lengths are generally used in restricted space for short pulls. Longer lengths are used for higher pulling loads where space is not restricted. Benefits
• Easy attachment to pulling lines.
• Reusable rawhide lace for lace closure.
• Galvanized steel for strength. Note: 1. Replacement rawhide lace. Catalog number 20920002. 2. See page V-43 for lace and rod closing instructions. Kellems® Wire Management Products Technical Information Pulling Grips

V-23www.hubbell-wiring.com Wiring Device-Kellems Commercial Construction/Light Duty Grips Light Duty Pulling Grips Light Duty Pulling Grips are made of galvanized steel in a single weave construction. They feature a flexible eye for easy attachment to a pulling line. Application Light Duty Grips are used in general underground electrical construction where pulling tensions are low. They are easy tools to use in wiring industrial plants and commercial buildings. Benefits

• Perfect tools for light pulling jobs.
• Installs easily on cable.
• Strong, galvanized steel construction. Junior Duty Pulling Grips Junior Pulling Grips feature a strong galvanized steel, single weave mesh. A flexible eye easily attaches to a pulling line, snake or fish tape. Application Designed to pull building wire, Junior grips are safe tools to use in pulling wire at low tension through conduit during electrical construction. Benefits
• Installs easily over building wire.
• Strong secure grip.
• Reusable.
• Pulls single cable or cable bundles. Junior Grip Kit Junior Grip Kit contains 6 grips, one of each size. Catalog number 033051114. See page V-12. Note: See page V-26 for building wire selection chart. Kellems® Wire Management Products Technical Information Pulling Grips

www.hubbell-wiring.comV-24 Wiring Device-Kellems Splicing Grips Wire Rope Splicing Kellems Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double and single weave for superior gripping ability. They are available with or without a rotating barrel which will help eliminate twist in the old rope from being transferred to the new rope. Application Wire Rope Grips are used for changing wire rope on oil derricks, large cranes, overhead cranes and drag lines. It provides a quick, safe, inexpensive temporary splice. By installing the used wire rope in one end and the new rope in the other, the new wire rope can be pulled in as the old one is pulled out. Benefits

• High strength for secure pulling.
• Easy installation.
• Flexible to pass through sheaves and blocks. Note: 1. During installation each end of the grip should be banded and taped down securely over the rope to insure smooth passage through sheaves and to guard against accidental release. See page V-15 for end bands. 2. The rotating barrel is not a swivel and will not turn while under tension. It can turn to relieve pulling torque when tension is relaxed. Cable Splicing Splicing Grips are made of galvanized steel in double or single weave mesh construction. They are available in various lengths and sizes to suit most applications. Application Splicing Grips are used as a temporary splice for rope, cable or wire rope. They can also be used as cable reinforcement, and can act as a shield to protect cables and hoses from abrasion. Benefits
• Easily installed or removed.
• Galvanized steel construction for strength.
• Flexible to follow cable path. Note: 1. During installation, each end of the splicing grip should be banded and taped down securely to the cable to insure smooth passage with the cable and guard against accidental release. 2. See page V-15 for end bands. Kellems® Wire Management Products Technical Information Splicing Grips

V-25www.hubbell-wiring.com Wiring Device-Kellems Number of Cables in One Grip 2 3 4 5 6 and 7 8 9 Grip Dia.Range Inches (cm) .30-.38 (.76-.97) .25-.31 (.63-.79) .22-.27 (.56-.69) .19-.24 (.48-.60) .17-.22 (.43-.56) .15-.19 (.38-.48) .14-.18 (.36-.46) .50-.61 (1.27-1.55) .38-.44 (.97-1.12) .31-.36 (.79-.91) .27-.31 (.69-.79) .24-.29 (.61-.74) .22-.26 (.56-.66) .19-.23 (.48-.58) .18-.21 (.46-.53) .62-.74 (1.57-1.88) .44-.59 (1.12-1.50) .36-.49 (.91-1.24) .31-.42 (.79-1.07) .29-.38 (.74-.97) .26-.34 (.66-.86) .23-.31 (.58-.79) .21-.28 (.53-.71) .75-.99 (1.90-2.51) .59-.75 (1.50-1.90) .49-.63 (1.24-1.60) .42-.54 (1.07-1.37) .38-.48 (.97-1.22) .34-.43 (.86-1.09) .31-.39 (.79-.99) .28-.35 (.71-.89) 1.00-1.24 (2.54-3.15) .75-.90 (1.90-2.29) .63-.76 (1.60-1.93) .54-.65 (1.37-1.65) .48-.58 (1.22-1.47) .43-.52 (1.09-1.32) .39-.46 (.99-1.17) .35-.42 (.89-1.07) 1.25-1.49 (3.17-3.78) .90-1.07 (2.29-2.72) .76-.89 (1.93-2.26) .65-.77 (1.65-1.96) .58-.67 (1.47-1.70) .52-.60 (1.32-1.52) .46-.54 (1.17-1.37) .42-.49 (1.07-1.24) 1.50-1.74 (3.81-4.42) 1.07-1.22 (2.72-3.10) .89-1.02 (2.26-2.59) .77-.88 (1.96-2.24) .67-.77 (1.70-1.96) .60-.69 (1.52-1.75) .54-.62 (1.37-1.57) .49-.56 (1.24-1.42) 1.75-1.99 (4.44-5.05) 1.22-1.53 (3.10-3.89) 1.02-1.28 (2.59-3.25) .88-1.10 (2.24-2.79) .77-.96 (1.96-2.44) .69-.86 (1.75-2.18) .62-.77 (1.57-1.96) .56-.71 (1.42-1.80) 2.00-2.49 (5.08-6.32) 1.53-1.83 (3.89-4.65) 1.28-1.53 (3.25-3.89) 1.10-1.32 (2.79-3.35) .96-1.16 (2.44-2.95) .86-1.03 (2.18-2.62) .77-.93 (1.96-2.36) .71-.85 (1.80-2.16) 2.50-2.99 (6.35-7.59) 1.83-2.14 (4.65-5.44) 1.53-1.79 (3.89-4.55) 1.32-1.54 (3.35-3.91) 1.16-1.35 (2.95-3.43) 1.03-1.20 (2.62-3.05) .93-1.08 (2.36-2.74) .85-.99 (2.16-2.51) 3.00-3.49 (7.62-8.86) 2.14-2.44 (5.44-6.20) 1.79-2.05 (4.55-5.21) 1.54-1.76 (3.91-4.47) 1.35-1.54 (3.43-3.91) 1.20-1.37 (3.05-3.48) 1.08-1.24 (2.74-3.15) .99-1.13 (2.51-2.87) 3.50-3.99 (8.89-10.13) 2.44-2.75 (6.20-6.98) 2.05-2.30 (5.21-5.84) 1.76-1.98 (4.47-5.03) 1.54-1.74 (3.91-4.42) 1.37-1.55 (3.48-3.94) 1.24-1.39 (3.15-3.53) 1.13-1.27 (2.87-3.23) 4.00-4.49 (10.16-11.40) 2.75-3.06 (6.98-7.77 ) 2.30-2.56 (5.84-6.50) 1.98-2.20 (5.03-5.59) 1.74-1.93 (4.42-4.90) 1.55-1.72 (3.94-4.37) 1.39-1.55 (3.53-3.94) 1.27-1.41 (3.23-3.58) 4.50-4.99 (11.43-12.67) Note: *This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section. It is always recommended that, when multiple cables are installed in a pulling grip, the tail end be banded and tightly taped after installation on the cable bundle. See page V-15 for end bands. Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1. Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration). 2. Divide the bundle circumference by 3.14 to determine the diameter. 3. Choose a grip offering a range of cable diameters the same as the cable diameter. For Pulling Grips* CAUTION: When a grip is used on multiple cables, the tail end of the grip should be banded after positioning on the cables. For Cables of Equal Diameters Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right. If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips. Kellems® Wire Management Products Technical Information Pulling Grips

www.hubbell-wiring.comV-26 Wiring Device-Kellems Cable Diameter Range In. (cm) Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip Model Catalog Number #14

19 Strand

#12 #10

37 Strand

#1/0 .25-.36 (.63-.91) 450 (2,002) 4-8 3-6 2-3 2 1 1 1 — — — J 25 03305001 .37-.49 (.94-1.24) 900 (4,003) 9-16 6-11 4-6 3 2 — — 1 1 1 J 37 03305002 .50-.61 (1.27-1.55) 1,300 (5,782) 16-25 11-17 7-10 4-5 3-4 2 2 — — — J 50 03305003 .62-.74 (1.57-1.88) 1,950 (8,674) 26-37 18-25 11-14 6-8 5-6 3 3 2 2 — J 62 03305004 .75-.99 (1.90-2.51) 2,800 (12,454) 37-66 26-47 15-27 9-16 6-11 4-7 4-5 3-4 3 2-3 J 75 03305005 1.00-1.24 (2.54-3.15) 3,900 (17,347 ) 66-104 47-74 28-43 16-24 11-17 8-10 6-8 5-7 4-5 4 J 100 03305006 Cable Diameter Range In. (cm) Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip Model Catalog Number #14

7 Strand

#12 #10 #1/0 .25-.36 (.63-.91) 450 (2,002) 2 2 1 1 — — — — — J 25 03305001 .37-.49 (.94-1.24) 900 (4,003) 3 2-3 2 — 1 1 1 — — J 37 03305002 .50-.61 (1.27-1.55) 1,300 (5,782) 4-5 4-5 3-4 2 — — — 1 — J 50 03305003 .62-.74 (1.57-1.88) 1,950 (8,674) 6-8 6-7 4-5 3 2 2 — — 1 J 62 03305004 .75-.99 (1.90-2.51) 2,800 (12,454) 9-16 8-14 6-10 4-6 3-4 3-4 2-3 2 — J 75 03305005 1.00-1.24 (2.54-3.15) 3,900 (17,347 ) 16-24 15-22 11-16 7-10 5-7 4-6 4 3 2-3 J 100 03305006 T.H.W. Building Wire Cable Diameter Range In. (cm) Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip Model Catalog Number #14 #12 #10 #1/0 .25-.36 (.63-.91) 450 (2,002) 2-4 2-3 2 1 1 1 — — — J 25 03305001 .37-.49 (.94-1.24) 900 (4,003) 5-7 4-5 3-4 2 — — 1 — — J 37 03305002 .50-.61 (1.27-1.55) 1,300 (5,782) 8-11 6-8 5-7 3-4 2 2 — 1 1 J 50 03305003 .62-.74 (1.57-1.88) 1,950 (8,674) 12-16 9-12 8-10 5-6 3-4 3 2 — — J 62 03305004 .75-.99 (1.90-2.51) 2,800 (12,454) 17-30 13-24 11-19 7-10 5-7 4-5 3-4 2 2 J 75 03305005 1.00-1.24 (2.54-3.15) 3,900 (17,347 ) 31-48 25-37 20-30 11-17 8-11 6-8 5-6 3-4 3 J 100 03305006 Kellems® Wire Management Products Technical Information Junior Pulling Grips Junior Pulling Grip Selection Chart These charts are a general guide to assist in the selection of the correct Junior Pulling Grip for pulling various groupings of building wire. It is not intended to be restrictive inasmuch as the use of “dummy" wires (short pieces of wire used to fill out the Grip) or the tight taping of the wires into a compact bundle may increase or decrease the number of wires per Grip.

V-27www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Support Grips - Heavy Duty, Standard Duty, Light Duty Tin-Coated Bronze/Stainless Steel Solid eye assemblies provide eye reinforcement at support hardware Four eye styles available: single (shown), double, universal, and offset Identification tag shows: catalog number, diameter range, agency approval, and bar code The strand equalizer positions wires for equal loading throughout the entire grip length The positive action mesh grip is designed for light duty up to heavy duty. Closed grips fit over the cable end, split grips wrap around the cable mid-span. The standard material is nonmagnetic, tin-coated bronze. Selected items are available in stainless steel. For exceptional immunity to rust and corrosion with superior strength and flexibility for heavy duty support application in harsh environments; contact the factory The endless weave provides easy installation onto cable and can be easily repositioned

www.hubbell-wiring.comV-28 Wiring Device-Kellems Single Eye, Closed Mesh For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Single Eye, Split Mesh, Lace Closing For permanent support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Single Eye, Split Mesh, Rod Closing For support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Standard Duty Support Grips Single Eye, Single Weave, Tin-Coated Bronze and Stainless Steel E M E M E M IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-29www.hubbell-wiring.com Wiring Device-Kellems Double Eye, Closed Mesh For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Double Eye, Split Mesh, Lace Closing For permanent support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Double Eye, Split Mesh, Rod Closing For support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Standard Duty Support Grips Double Eye, Single Weave, Tin-Coated Bronze and Stainless Steel E M E M E M IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

www.hubbell-wiring.comV-30 Wiring Device-Kellems Offset Eye, Closed Mesh For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Offset Eye, Split Mesh, Lace Closing For permanent support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Offset Eye, Split Mesh, Rod Closing For support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Standard Duty Support Grips Offset Eye, Single Weave, Tin-Coated Bronze and Stainless Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-31www.hubbell-wiring.com Wiring Device-Kellems Universal Eye, Closed Mesh For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Universal Eye, Split Mesh, Lace Closing For permanent support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Universal Eye, Split Mesh, Rod Closing For support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Standard Duty Support Grips Universal Eye, Single Weave, Tin-Coated Bronze and Stainless Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

www.hubbell-wiring.comV-32 Wiring Device-Kellems Heavy Duty, Single Eye, Closed Mesh For heavy duty permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel .75"-.99" (1.90-2.51) 2,820 (12,543) 4,200 (18,683) 10" (25.40) 25" (63.50) 02206010 02406010 1.00"-1.24" (2.54-3.15) 4,280 (19,037) 7,30 0 (32,472) 12" (30.48) 28" (71.12) 02206011 02406011 1.25"-1.49" (3.17-3.78) 4,280 (19,037) 7,30 0 (32,472) 12" (30.48) 30" (76.20) 02206012 02406012 1.50"-1.99" (3.81-5.05) 4,280 (19,037) 11,150 (49,598) 12" (30.48) 34" (86.36) 02206013 02406013 Single Eye, Split Mesh, Lace Closing For permanent support when cable end is not available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel .75"-.99" (1.90-2.51) 2,820 (12,543) 4,200 (18,683) 10" (25.40) 25" (63.50) 02207010 02407010 1.00"-1.24" (2.54-3.15) 4,280 (19,037) 7,30 0 (32,472) 12" (30.48) 28" (71.12) 02207011 02407011 1.25"-1.49" (3.17-3.78) 4,280 (19,037) 7,30 0 (32,472) 12" (30.48) 30" (76.20) 02207012 02407012 1.50"-1.99" (3.81-5.05) 4,280 (19,037) 11,150 (49,598) 12" (30.48) 34" (86.36) 02207013 02407013 Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Heavy Duty Support Grips Single Eye, Double Weave, Tin-Coated Bronze and Stainless Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-33www.hubbell-wiring.com Wiring Device-Kellems Double Eye, Closed Mesh For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel .75"-.99" (1.90-2.51) 2,820 (12,543) 4,250 (18,905) 10" (25.40) 25" (63.50) 02206001 02406001 1.00"-1.24" (2.54-3.15) 4,280 (19,037) 7,30 0 (32,472) 10" (25.40) 28" (71.12) 02206002 02406002 1.25"-1.49" (3.17-3.78) 4,280 (19,037) 7,30 0 (32,472) 10" (25.40) 30" (76.20) 02206003 02406003 1.50"-1.99" (3.81-5.05) 4,280 (19,037) 11,100 (49,375) 10" (25.40) 34" (86.36) 02206004 02406004 2.00"-2.49" (5.08-6.32) 02206005 02406005 2.50"-2.99" (6.35-7.59) 8,050 (35,806) 20,100 (89,409) 12" (30.48) 38" (96.52) 02206006 02406006 3.00"-3.49" (7.62-8.86) 02206007 02406007 3.50"-3.99" (8.89-10.13) 02206008 — 4.00"-4.49" (10.16-11.40) 4.50"-4.99" (11.43-12.67) Double Eye, Split Mesh, Lace Closing For support when cable end is not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel .75"-.99" (1.90-2.51) 2,820 (12,543) 4,250 (18,905) 10" (25.40) 25" (63.50) 02207001 02407001 1.00"-1.24" (2.54-3.15) 4,280 (19,037) 7,30 0 (32,472) 10" (25.40) 28" (71.12) 02207002 02407002 1.25"-1.49" (3.17-3.78) 4,280 (19,037) 7,30 0 (32,472) 10" (25.40) 30" (76.20) 02207003 02407003 1.50"-1.99" (3.81-5.05) 4,280 (19,037) 11,150 (49,598) 10" (25.40) 34" (86.36) 02207004 02407004 2.00"-2.49" (5.08-6.32) 02207005 02407005 2.50"-2.99" (6.35-7.59) 8,050 (35,806) 20,150 (89,632) 12" (30.48) 38" (96.52) 02207006 02407006 3.00"-3.49" (7.62-8.86) 02207007 02407007 3.50"-3.99" (8.89-10.13) 02207008 02407008 4.00"-4.49" (10.16-11.40) 12,070 (53,687) 30,200 (134,336) 12" (30.48) 46" (116.84) 02207009 02407009 4.50"-4.99" (11.43-12.67) Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Heavy Duty Support Grips Double Eye, Double Weave, Tin-Coated Bronze and Stainless Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

www.hubbell-wiring.comV-34 Wiring Device-Kellems .31'' (.79) Dia. .29'' (.74) 4.86'' (12.42) 2.00'' (5.08) Screw Hook Catalog Number 20303001 Yield Strength 900 lbs (4003 N) Light Duty, Single Eye, Closed Mesh, Single Weave For permanent support when cable end is available to be installed. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Heavy Duty, Single Eye, Closed Mesh, Multi-Weave For permanent support when cable end is available to be installed. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Tin-Coated Bronze Stainless SteelTin-Coated Bronze Stainless Steel Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Service Drop Grips Single Eye, Tin-Coated Bronze and Stainless Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-35www.hubbell-wiring.com Wiring Device-Kellems Light Duty, Universal Eye, Closed Mesh, Single Weave For permanent support when cable end is available to be installed. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave For permanent support when cable end is available to be installed. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Service Drop Grips Universal Eye, Tin-Coated Bronze IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

www.hubbell-wiring.comV-36 Wiring Device-Kellems Safety Spring Maximum Deflection Inches/Lbs (cm/N) Approx. Breaking Strength Lbs. (N) Length* Inches (cm) Diameter Inches (cm) Model Lbs. (N) Catalog Number 2¾" at 40 lbs. (6.98 at 178) (178) 20302001 3¹⁄₈" at 80 lbs. (7.94 at 356) (356) 20302002 Note: Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar. *No load. Single Eye, Wide Range Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Universal Eye, Wide Range Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. **Item indicated is not UL listed. Kellems® Wire Management Products Bus Drop Support Grips Single Eye, Universal Eye, Galvanized Steel Bus Drop Grips and Safety Springs Kellems Bus Drop Grips are offered with either a single eye or universal bale attachment. The mesh is single weave galvanized steel with the patented wide range construction. They are suitable for indoor use only. Consult Technical Service for Stainless Steel Grips. Application Bus Drop Grips provide a safe, easy and economical method to support flexible cord or bus drop cable at bus duct and other industrial areas. Benefits

• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction. Safety Spring Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar. Strain Relief Grip Bus Drop Grips Motor Box Safety Spring Strain Relief Grip IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-37www.hubbell-wiring.com Wiring Device-Kellems Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Cable Sizes In. (cm) .50"- .62" (1.27-1.57) .63"-.74" (1.60-1.88) .75"- .99" (1.90-2.51) 1.00"- 1.24" (2.54-3.15) 1.25"- 1.49" (3.17-3.78) 1.50"-1.74" (3.81-4.42) 1.75"-1.99" (4.44-5.05) 2.00"- 2.49" (5.08-6.32) 2.50" -2.99" (6.35-7.59) 3.00"- 3.49" (7.62-8.86) 3.50"- 3.99" (8.89-10.13) Model R050 R062 R075 R100 R125 R150 R175 R200 R250 R300 R350 Length In. (cm) Conduit Sizes Inches Catalog Number Approx. Breaking Strength Lbs. (N) 02211106 530 (2,357) 1 02211100 490 (2,179) 02211101 790 (3,514) 1¼ 02211001 450 (2,002) 02211002 740 (3,292) 02211003 1,030 (4,581) 1½ — 02211006 690 (3,069) 02211007 970 (4,315) 02211009 1,610 (7,161) 2 — 02211107 640 (2,847) 02211010 920 (4,092) 02211012 1,520 (6,761) 02211013 1,610 (7,161) 2½ — — — — 02211017 1,510 (6,716) 02211018 1,610 (7,161) 02211019 2,150 (9,563) — — — — 3 — — — 02211022 1,340 (5,960) 02211023 1,400 (6,227) 02211024 1,490 (6,627) 02211025 1,990 (8,851) 02211026 3,260 (14,500) — — — 2,970 (13,211) 02211034 3,260 (14,500) — — 1,670 ( 7,24 8) 02211041 2,680 (11,921) 02211042 2,890 (12,855) 02211043 4,080 (18,148) 2,150 (9,563) 02211062 2,860 (12,721) 02211063 3,130 (13,922) 2,245 (9,986) 02211073 2,245 (9,986) Note: See page V-45 for multiple cables in a single conduit riser grip. Wire Management Products Conduit Riser Grips Ring Type, Single Weave, Tin-Coated Bronze Single Weave, Closed Mesh Kellems® Conduit Riser Support Grips are available in closed mesh and in split mesh with lace or rod closures, to cover all applications including single cable or multiple wire support. Refer to page V-45 for grip selection assistance for cable bundles. The standard material is tin-coated bronze strand. The grip is permanently fastened to a support ring, resulting in a one piece unit which will allow air ventilation within the conduit. The ring will fit standard electrical rigid metal conduit and schedule 40 rigid PVC conduit only. See page V-40 for ring dimensions. For permanent support when cable end is available to be installed through the grip. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 and V-45.

www.hubbell-wiring.comV-38 Wiring Device-Kellems Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Cable Sizes In. (cm) .75"- .99" (1.90-2.51) 1.00"- 1.24" (2.54-3.15) 1.25"- 1.49" (3.17-3.78) 1.50"-1.74" (3.81-4.42) 1.75"- 1.99" (4.44-5.05) 2.00"- 2.49" (5.08-6.32) 2.50"- 2.99" (6.35-7.59) 3.00"- 3.49" (7.62-8.86) 3.50" -3.99" (8.89-10.13) Model RS075 RS100 RS125 RS150 RS175 RS200 RS250 RS300 RS350 Length In. (cm) Conduit Sizes Inches Catalog Number Approx. Breaking Strength Lbs. (N) 02212003 1,58 0 ( 7,028) 1½ 02212007 1,500 (6,672) 2 02212010 1,430 (6,361) 02212012 1,930 (8,585) 02212013 2,040 (9,074) 2½ — — 02212017 1,910 (8,496) 02212018 2,040 (9,074) 3 — — 02212023 1,78 0 ( 7,917 ) 02212024 1,890 (8,407) 02212025 2,520 (11,209) 02212026 4,300 (19,126) — — — 3,910 (17,392) 02212034 4,300 (19,126) — — 4 — — — — 02212040 2,110 (9,385) 02212041 3,530 (15,701) 02212042 3,820 (16,991) 02212043 5,380 (23,930) 2,860 (12,721) — — 2,955 (13,144) Note: See page V-45 for multiple cables in a single conduit riser grip. Kellems® Wire Management Products Conduit Riser Grips Ring Type, Double Weave, Tin-Coated Bronze Double Weave, Split Mesh, Lace Closing Kellems® Conduit Riser Support Grips will support cable runs in vertical or sloping standard rigid conduit. The grip is fastened to a support ring which seats on the rim of the conduit. The entire grip is supported by the conduit itself and no other hardware is required. See page V-40 for ring dimensions. The rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only. For permanent support when cable end is not available. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 and V-45.

V-39www.hubbell-wiring.com Wiring Device-Kellems Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Cable Sizes In. (cm) .75"- .99" (1.90-2.51) 1.00"- 1.24" (2.54-3.15) 1.25"- 1.49" (3.17-3.78) 1.50"-1.74" (3.81-4.42) 1.75"- 1.99" (4.44-5.05) 2.00"- 2.49" (5.08-6.32) 2.50"- 2.99" (6.35-7.59) 3.00"- 3.49" (7.62-8.86) 3.50" -3.99" (8.89-10.13) Model RR075 RR100 RR125 RR150 RR175 RR200 RR250 RR300 RR350 Length In. (cm) Conduit Sizes Inches Catalog Number Approx. Breaking Strength Lbs. (N) 02213003 1,020 (4,537) 1½ 02213007 970 (4,315) 02213009 1,610 (7,161) 2 — 02213012 1,520 (6,761) 02213013 1,610 (7,161) 2½ — — 02213017 1,510 (6,716) 02213018 1,610 (7,161) 3 — — 02213023 1,400 (6,227) 02213024 1,490 (6,627) 02213025 1,990 (8,851) 02213026 3,260 (14,500) — — — 2,970 (13,211) — — — 2,670 (11,876) 02213042 2,890 (12,855) — — Note: See page V-45 for multiple cables in a single conduit riser grip. Kellems® Wire Management Products Conduit Riser Grips Ring Type, Single Weave, Tin-Coated Bronze Single Weave, Split Mesh, Rod Closing Benefits

• Easy and fast to install.
• Will not damage electrical cable.
• Allows cable to expand or contract.
• Ideal way to hold cable in vertical conduit.
• Prevents cable creep in conduit.
• Helps prevent cable pullouts.
• The rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only.
• For support when cable end is not available. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 and V-45.

www.hubbell-wiring.comV-40 Wiring Device-Kellems Kellems® Wire Management Products Conduit Riser Grips Conduit Riser Support Grip-Ring Dimensions O.D. I.D. T T S O.D. I.D. T Conduit Size ¾" and 1" Conduit Size 1¼" to 6" Conduit Size Inches Ring Number O.D. Inches (cm) I.D. Inches (cm) S Inches (cm) T Inches (cm) C-¾ C-1 C-1¼ C-1½ C-2 C-2½ C-3 C-3½ C-4 C-4½ C-5 C-6 .94" (2.39) 1.17" (2.97) 1.50" (3.81) 1.76" (4.47) 2.23" (5.66) 2.67" (6.78) 3.20" (8.13) 3.80" (9.65) 4.30" (10.92) 4.80" (12.19) 5.30" (13.46) 6.30" (16.00) .62" (1.57) .80" (2.03) 1.03" (2.62) 1.23" (3.12) 1.55" (3.94) 2.05" (5.21) 2.55" (6.48) 3.05" (7.75) 3.55" (9.02) 4.03" (10.24) 4.46" (11.33) 5.36" (13.61) 1.31" (3.33) 1.52" (3.86) 1.97" (5.00) 2.40" (6.10) 2.97" (7.54) 3.47" (8.81) 3.94" (10.01) 4.45" (11.30) 4.96" (12.60) 5.96" (15.14) .19" (.48) .19" (.48) .16" (.41) .16" (.41) .16" (.41) .16" (.41) .22" (.56) .22" (.56) .22" (.56) .22" (.56) .22" (.56) .25" (.63) Conduit Ring Dimensions Ring dimensions are found in the chart below. The ring material is corrosion resistant. These rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-45.

V-41www.hubbell-wiring.com Wiring Device-Kellems Support Grip Selection Chart Grip Styles Application Page Closed mesh Split lace closing Split rod closing Material* Standard support grips Heavy duty grips Service drop Bus drop Conduit riser Fiber optic cable support grips Standard, permanent support, cable end available. Standard, permanent support, cable end unavailable. Standard, temporary support, cable end unavailable. Tape or band tail end of wire mesh grip after positioning for permanent support. Tin-coated bronze standard or stainless steel by special request. Support vertical runs to 99 ft. loads to 600 lbs. Support vertical runs over 100 ft. loads over 600 lbs. Light duty to support service entrance cable. Light duty support, indoors only, on Bus drop cable. Support cable runs in rigid (Schedule 40) conduit. Support fiber optic cable. V-28 to V-36 V-28 to V-33 V-28 to V-31 V-28 to V-34 V-28 to V-31 V-32, V-33 V-34, V-35 V-36 V-37 to V-39 V-50 Note: *Most catalog listed support grips are made of tin-coated bronze strand. To order stainless steel support grips, change the first three catalog number digits from 022-0x-xxx to 024-0x-xxx. Consult Technical Service for details. Eye Styles Select the Correct Support Grip Each Kellems grip is designed to work on a specific range of cable diameters. Step 1 Refer to the Kellems chart below to determine the grip style best suited for your application. Step 2 Determine your cable outside diameter. Step 3 Find the grip size that encompasses your cable diameter. Step 4 Whenever possible, use a closed mesh that assembles over the cable end. If the cable end is not available, use a split mesh. Step 5 Where available, select an eye style that suits your needs. Step 6 Select the proper material—tinned bronze or stainless steel*. Step 7 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough. Refer to page V-42 for safety and working load considerations. Kellems® Wire Management Products Technical Information Support Grips Kellems® Support Grips Kellems Support Grips are used to hold the weight of electrical cable as it hangs in a vertical, sloping or horizontal position. Electrical cable must be supported, or its dead weight can cause excessive strain or pullout at the connections resulting in power failure. Support grips also absorb additional strain from flexure, vibration, expansion and contraction. Kellems Support Grips listed in this catalog are made of high grade, non-magnetic tin-coated bronze strand. Stainless steel grips, made of alloy 302–304 SST for severe service or unusual environmental conditions, are available on request. Single Double Universal Offset 1. Support grips are to be installed by a qualified individual in accordance with all applicable national and local safety, electrical and rigging codes. 2. Ensure that the correct grip is selected for your specific needs. 3. Do not use a support grip for any application other than supporting cable. 4. Thoroughly examine the grip for damage. Do not use a damaged grip. 5. Ensure that the recommended work load of the grip is suitable for the application. Never use grips at their approximated rated breaking strength. A safety factor of 10 is recommended for support grips. 6. Do not alter grips in any way. For example, do not flatten, straighten, bend or otherwise modify eye tubes, hooks, and strand equalizers. 7. Do not attach any type of hook, clamp or other hardware directly to the stranded bale of a “U” eye support grip. The formed eye tube is the only acceptable means of attachment to external hardware. 8. Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against accidental release of the grip. Accidental release can occur if an object contracts and pushes against the tail end of the mesh, thereby expanding and releasing it’s hold. CAUTION: It is very important to comply with all of the following precautions.

www.hubbell-wiring.comV-42 Wiring Device-Kellems Examples Approx. Breaking Safety Max. Recommended Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027 Support Grips 1,610 (7,161) 10 161 (716) 02202019 The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances. It is the end-user’s decision to determine how much of a safety factor is acceptable for the application. The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric unit of weight (kilograms) the conversion factor is 9.808 newtons/kilogram. Support Grip Materials Material Features Grip Type Tin-coated bronze wire • Corrosion resistant for normal outside areas • Support grips

• Non-magnetic • Service drop grips
• Moderate strength • Conduit riser grips Stainless steel wire • High strength • Support grips (302-304) • Corrosion resistant • Hose containment grips Galvanized steel wire • Slightly magnetic • Bus drop grips
• Not subject to continuous outside environment Approvals CSA Certifications are indicated on appropriate product catalog pages. Note: It is always recommended that the tail end of the grip be banded after the installation on the cable to prevent accidental release of the mesh. See page V-15 for end bands. Kellems® Wire Management Products Technical Information Support Grips The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads. The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories. It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same. The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application. These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate. Where the conditions of the application are not well defined or known, or where risk of injury to persons or property is involved, a greater safety factor should be utilized. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained, and inspected by the user at a frequency appropriate for the use and condition of the grip. Safety And Working Load Factors For Wire Mesh Grips Under normal conditions, Kellems’ recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips.

V-43www.hubbell-wiring.com Wiring Device-Kellems Split Support Grip Lace Closing Instructions Single Weave Grips should be laced with single strand lacing; double weave with double strand. Lacing strands should be the same material as the grip. Kellems supplies the appropriate lacing with each grip. 1. Start the lacing at the lead or anchoring end of the grip. Thread the lacings through the first two loops of the split and pull through until the lacings are centered at this point. Lace as you would your shoe, crossing the lacings before lacing the next two loops. 2. Don’t pull lacing too tight. Leave a space between adjoining loops approximately equal to the width of one diamond of the mesh. 3. Twist the lacing strands tightly together at the tail end of the grip. 4. Wrap the ends of the lacings once or twice tightly around the tail of the grip, twisting the ends together securely. Excess lace can be cut off. Split Support Grip Rod Closing Instructions The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the mesh pass around the rod and match up with the strands from the opposite direction. The rod does not touch the cable at any point and therefore cannot cut the cable. Rod Closing Grips are reusable. They may be removed and reused as many times as desired. 1. Fast to install Wrap the grip around the cable and thread the rod through the pre-formed loops with a corkscrew motion, using the curved end of the rod to engage the loops. 2. The action required is a steady push and twist simultaneously. The fingers of the left hand are used to bring the loops together just ahead of the hook on the end of the rod. 3. To remove, simply pull the rod out. Kellems® Wire Management Products Technical Information Support Grips

www.hubbell-wiring.comV-44 Wiring Device-Kellems Number of Cables in One Grip 2 3 4 5 6 and 7 8 9 Grip Dia. Range Inches (cm) .30-.38 (.76-.97) .25-.31 (.63-.79) .22-.27 (.56-.69) .19-.24 (.48-.61) .17-.22 (.43-.56) .15-.19 (.38-.48) .14-.18 (.36-.46) .50-.61 (1.27-1.55) .38-.44 (.97-1.12) .31-.36 (.79-.91) .27-.31 (.69-.79) .24-.29 (.61-.74) .22-.26 (.56-.66) .19-.23 (.48-.58) .18-.21 (.46-.53) .62-.74 (1.57-1.88) .44-.59 (1.12-1.50) .36-.49 (.91-1.24) .31-.42 (.79-1.07) .29-.38 (.74-.97) .26-.34 (.66-.86) .23-.31 (.58-.79) .21-.28 (.53-.71) .75-.99 (1.90-2.51) .59-.75 (1.50-1.90) .49-.63 (1.24-1.60) .42-.54 (1.07-1.37) .38-.48 (.97-1.22) .34-.43 (.86-1.09) .31-.39 (.79-.99) .28-.35 (.71-.89) 1.00-1.24 (2.54-3.15) .75-.90 (1.90-2.29) .63-.76 (1.60-1.93) .54-.65 (1.37-1.65) .48-.58 (1.22-1.47) .43-.52 (1.09-1.32) .39-.46 (.99-1.17) .35-.42 (.89-1.07) 1.25-1.49 (3.17-3.78) .90-1.07 (2.29-2.72) .76-.89 (1.93-2.26) .65-.77 (1.65-1.96) .58-.67 (1.47-1.70) .52-.60 (1.32-1.52) .46-.54 (1.17-1.37) .42-.49 (1.07-1.24) 1.50-1.74 (3.81-4.42) 1.07-1.22 (2.72-3.10) .89-1.02 (2.26-2.59) .77-.88 (1.96-2.24) .67-.77 (1.70-1.96) .60-.69 (1.52-1.75) .54-.62 (1.37-1.57) .49-.56 (1.24-1.42) 1.75-1.99 (4.44-5.05) 1.22-1.53 (3.10-3.89) 1.02-1.28 (2.59-3.25) .88-1.10 (2.24-2.79) .77-.96 (1.96-2.44) .69-.86 (1.75-2.18) .62-.77 (1.57-1.96) .56-.71 (1.42-1.80) 2.00-2.49 (5.08-6.32) 1.53-1.83 (3.89-4.65) 1.28-1.53 (3.25-3.89) 1.10-1.32 (2.79-3.35) .96-1.16 (2.44-2.95) .86-1.03 (2.18-2.62) .77-.93 (1.96-2.36) .71-.85 (1.80-2.16) 2.50-2.99 (6.35-7.59) 1.83-2.14 (4.65-5.44) 1.53-1.79 (3.89-4.55) 1.32-1.54 (3.35-3.91) 1.16-1.35 (2.95-3.43) 1.03-1.20 (2.62-3.05) .93-1.08 (2.36-2.74) .85-.99 (2.16-2.51) 3.00-3.49 (7.62-8.86) 2.14-2.44 (5.44-6.20) 1.79-2.05 (4.55-5.21) 1.54-1.76 (3.91-4.47) 1.35-1.54 (3.43-3.91) 1.20-1.37 (3.05-3.48) 1.08-1.24 (2.74-3.15) .99-1.13 (2.51-2.87) 3.50-3.99 (8.89-10.13) 2.44-2.75 (6.20-6.98) 2.05-2.30 (5.21-5.84) 1.76-1.98 (4.47-5.03) 1.54-1.74 (3.91-4.42) 1.37-1.55 (3.48-3.94) 1.24-1.39 (3.15-3.53) 1.13-1.27 (2.87-3.23) 4.00-4.49 (10.16-11.40) 2.75-3.06 (6.98-7.77 ) 2.30-2.56 (5.84-6.50) 1.98-2.20 (5.03-5.59) 1.74-1.93 (4.42-4.90) 1.55-1.72 (3.94-4.37) 1.39-1.55 (3.53-3.94) 1.27-1.41 (3.23-3.58) 4.50-4.99 (11.43-12.67) Note: *This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Riser multiple cable selection, see page V-45. It is always recommended that, when multiple cables are installed in a Support Grip, the tail end of the grip be banded after installation on the cable bundle. See page Tech-23 for cable and wire charts. For Support Grips Only* Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1. Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration). 2. Divide the bundle circumference by 3.14 to determine the diameter. 3. Choose a grip offering a range of cable diameters the same as the cable diameter. For Cables of Equal Diameters Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right. If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips. Kellems® Wire Management Products Technical Information Support Grips

V-45www.hubbell-wiring.com Wiring Device-Kellems Number of Equal Diameter Cables in One Grip 2 3 4 5 6 and 7 8 9 Grip Dia. Range Inches (cm) .29-.36 (.74-.91) .24-.30 (.61-.76) .21-.25 (.53-.63) .18-.22 (.46-.56) .16-.20 (.41-.51) .15-.18 (.38-.46) .14-.17 (.36-.43) .50-.62 (1.27-1.57) .37-.43 (.94-1.09) .31-.36 (.79-.91) .26-.30 (.66-.76) .23-.27 (.58-.69) .21-.24 (.53-.61) .19-.22 (.48-.56) .18-.20 (.46-.51) .63-.74 (1.60-1.88) .44-.58 (1.12-1.47) .37-.48 (.94-1.22) .31-.41 (.79-1.04) .28-.36 (.71-.91) .25-.32 (.63-.81) .23-.29 (.58-.74) .21-.27 (.53-.69) .75-.99 (1.90-2.51) .59-.72 (1.50-1.83) .49-.60 (1.24-1.52) .42-.51 (1.07-1.30) .37-.45 (.94-1.14) .33-.40 (.84-1.02) .30-.36 (.76-.91) .28-.34 (.71-.86) 1.00-1.24 (2.54-3.15) .73-.87 (1.85-2.21) .61-.72 (1.55-1.83) .52-.61 (1.32-1.55) .46-.54 (1.17-1.37) .41-.48 (1.04-1.22) .37-.43 (.94-1.09) .35-.40 (.89-1.02) 1.25-1.49 (3.17-3.78) .88-1.01 (2.24-2.57) .73-.85 (1.85-2.16) .62-.71 (1.57-1.80) .55-.63 (1.40-1.60) .49-.56 (1.24-1.42) .44-.51 (1.12-1.30) .41-.47 (1.04-1.19) 1.50-1.74 (3.81-4.42) 1.02-1.16 (2.59-2.95) .86-.96 (2.18-2.44) .72-.81 (1.83-2.06) .64-.72 (1.63-1.83) .57-.64 (1.45-1.63) .52-.58 (1.32-1.49) .48-.54 (1.22-1.37) 1.75-1.99 (4.44-5.05) 1.17-1.44 (2.97-3.66) .97-1.20 (2.46-3.05) .82-1.02 (2.08-2.59) .73-.90 (1.85-2.29) .65-.80 (1.65-2.03) .59-.72 (1.50-1.83) .55-.67 (1.40-1.70) 2.00-2.49 (5.08-6.32) 1.45-1.73 (3.68-4.39) 1.21-1.45 (3.07-3.68) 1.03-1.22 (2.62-3.10) .91-1.08 (2.31-2.74) .81-.96 (2.06-2.44) .73-.87 (1.85-2.21) .68-.81 (1.73-2.06) 2.50-2.99 (6.35-7.59) 1.74-2.02 (4.42-5.13) 1.46-1.69 (3.71-4.29) 1.23-1.43 (3.12-3.63) 1.09-1.26 (2.77-3.20) .97-1.11 (2.46-2.82) .83-1.01 (2.11-2.57) .82-.94 (2.08-2.39) 3.00-3.49 (7.62-8.86) 2.03-2.31 (5.16-5.87) 1.70-1.93 (4.32-4.90) 1.44-1.63 (3.66-4.14) 1.27-1.44 (3.23-3.66) 1.12-1.27 (2.84-3.23) 1.02-1.15 (2.59-2.92) .95-1.08 (2.41-2.74) 3.50-3.99 (8.89-10.13) Note: *This chart is to be used for determining grip size when multiple cables are held in a single Conduit Riser Grip. For Support Grip multiple cable selection, see page V-44. It is always recommended that, when multiple cables are installed in a Conduit Riser Grip, the tail end of the grip be banded after installation on the cable bundle. See page Tech-23 for cable and wire charts. Kellems® Wire Management Products Technical Information Conduit Riser Support Grips For Conduit Riser Grips Only* Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1. Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration). 2. Divide the bundle circumference by 3.14 to determine the diameter. 3. Choose a grip offering a range of cable diameters the same as the cable diameter. For Cables of Equal Diameters Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right. If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.

www.hubbell-wiring.comV-46 Wiring Device-Kellems OPTISOK® Grip is a revolutionary tool to pull preterminated fiber optic cables. They will protect the connectors and guide the bundle through the pulling environment Pulling Grips are used for outside plant cable. They are easy to install and remove, reusable, and have a slim profile for small build up Grips for cable support are easy to install or position. They come in a closed style when the cable end is available, and a split rod style for mid-span installation. Will support the cable’s weight as it hangs in vertical, sloping or horizontal position Kellems® Wire Management Products Fiber Optic Cable Grips Pulling and Support Grips

V-47www.hubbell-wiring.com Wiring Device-Kellems OPTISOK® Non-Metallic Fiber Optic Pulling Tool Bundle/Size Range Inches (cm) Approx. O/A Length Inches (cm) Ring O.D. Inches (cm) Ring Thickness Inches (cm) Maximum Work Load Lbs. (N) Catalog Number Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel Diameter Range Inches (cm) Mesh Length Inches (cm) Eye Length Inches (cm) Eye Diameter Inches (cm) Lug Diameter Inches (cm) Maximum Breaking Strength Lbs. (N) Catalog Number Kellems® Wire Management Products Fiber Optic Cable Pulling Grips Special Purpose OPTISOK® Non-metallic Fiber Optic Pulling Tool For Preterminated, Inside Plant Fiber Optic Cables and Bundles of Twisted Pair Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-51 to V-54.

www.hubbell-wiring.comV-48 Wiring Device-Kellems Fiber Optic Pulling Grip, Flexible Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) D Approx. Inches (cm) Catalog Number Fiber Optic Pulling Grip, Swivel Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) D Approx. Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Fiber Optic Cable Pulling Grips Double/Single Weave Mesh, Galvanized Steel, for Outside Plant Cable IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-51 to V-54. EM D EM D

V-49www.hubbell-wiring.com Wiring Device-Kellems Fiber Optic Pulling Grip, Flexible Eye, Low Profile, Double/Single Weave Mesh Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number Fiber Optic Slack Pulling Grip, Split Mesh Rod Closing, Single Weave Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. Kellems® Wire Management Products Fiber Optic Cable Pulling Grips Galvanized Steel for Outside Plant Cable IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-51 to V-54. EM EM

www.hubbell-wiring.comV-50 Wiring Device-Kellems E M E M Kellems® Wire Management Products Fiber Optic Cable Support Grips Single Weave, Tin-Coated Bronze Fiber Optic Single Eye Cable Support Grip, Closed Mesh, Single Weave For permanent support when cable end is available to be installed through grip. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number Fiber Optic Single Eye Cable Support Grip, Split Mesh, Rod Closing, Single Weave For support when cable end not available. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-51 to V-54.

V-51www.hubbell-wiring.com Wiring Device-Kellems Kellems has wide experience with grips for use with fiber optic cable. As the industry leader in producing wire mesh grips for the stringent requirements of fiber optic applications, Kellems has developed several series of grips for use with fiber optic communications cable. These grips include pulling grips with built in swivels, grips with steel ends to protect fragile cable ends, grips with low profiles to pull cables in tight places and the OPTISOK ® an effective tool to place preterminated cables. Also available are grips to support fiber optic cable. Kellems® Wire Management Products Technical Information Fiber Optic Pulling and Support Grips Examples Approx. Breaking Safety Max. Recommended Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number Pulling Grips 2,500 (11,120) 5 500 (2,224) 033291196 Support Grips 400 (1,779) 10 40 (178) 022291004 The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances. It is the end-user’s decision to determine how much of a safety factor is acceptable to for the application. Fiber Optic Grip Materials Material Features Product Group Galvanized steel wire • High strength • Pulling grips

• Not subject to continuous outside environment Tin-coated bronze wire • Corrosion resistant for normal outside areas • Support grips
• Non-magnetic
• Moderate strength Non-metallic braid • Superior flex life • OPTISOK®
• Non-conductive
• Corrosion resistant
• Moderate strength Approvals CSA Certification is indicated on appropriate product catalog pages. The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads. The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories. It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same. The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application. These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate. Where the conditions of the application are not well defined or known or where risk of injury to persons or property is involved, a greater safety factor should be utilized. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained and inspected by the user at a frequency appropriate for the use and condition of the grip. For grip applications on materials other than those that the grips have been specifically designed for, consult the factory. Safety And Working Load Factors For Wire Mesh Grips Select the Correct Fiber Optic Grip Each Kellems grip is designed to work on a specific range of cable diameters. Step 1 Determine your cable outside diameter. Step 2 Find the grip size that encompasses your cable diameter. Step 3 Whenever possible, use a closed mesh that assembles over the cable end. If the cable end is not available, use a split mesh. Step 4 Where available, select an eye style that suits your needs. Step 5 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough. Under normal conditions, Kellems’ recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips.

www.hubbell-wiring.comV-52 Wiring Device-Kellems How to Select OPTISOK®

• Identify connector bundle diameter to be inserted into the OPTISOK®.
• Choose appropriate catalog number based on size range. Installation Information Step 1 Expand open end of OPTISOK® and gently work in fiber optic connector bundle. Step 2 Still gently, work connector bundle up to the forward section of the OPTISOK®. Step 3 Starting at approximately 6" (15.2cm) from tail end of OPTISOK®, tightly fold over the OPTISOK® around cables and tape wrapped section 3" (7.62cm) past tail end onto the bundle. Step 4 Securely attach pulling line or tape to pulling ring. Note: To remove OPTISOK® carefully unwrap tape and slide out cables and connectors or cut OPTISOK® away without damaging connectors or cables. Kellems® Wire Management Products Technical Information OPTISOK® Pulling Grips Kellems offers a unique and simple to use tool for the installation of preconnectorized fiber optic cables, jumpers and bundles of twisted pair communication cables - the OPTISOK The OPTISOK® is a highly flexible and expandable nonmetallic sleeve open on one end and with a pulling ring on the other. It will expand to enclose the larger group of fiber optic connectors and grab the cable below the connector bundle by wrapping and taping to provide a gripping tool that will grab the cable(s) below the connectors. The pulling ring can be attached to a pulling line or fish tape and the OPTISOK ® will act as the pulling tool. OPTISOK® will contain and protect the connector bundle and save time and labor by making the pulling job easier, protecting the connectors from possible damage during the pull and facilitating the passage of the connector bundle through cramped and tight spaces. The OPTISOK ® can be used to pull cables through plenums, underfloor duct, office partitions, raised access floors and conduits. Three sizes are available for all applications. Step 1 Step 2 Step 3 Step 4

V-53www.hubbell-wiring.com Wiring Device-Kellems Pulling Grip for Loose Tube Fiber Optic Cable Kellems offers a wire mesh specifically designed to pull loose tube fiber optic cable and meet the special pulling requirements recommended by fiber optic cable manufacturers. Many fiber optic cable manufacturers require special cable preparation prior to pulling where a short section of the outer jacket is stripped off exposing the aramid strength member. This creates two cable diameters, one including the jacket and a second smaller diameter at the strength member. Kellems fiber grip with its special weave will accommodate and securely grab both diameters, at the outside jacket and the internal aramid strength member. Additionally, this galvanized steel mesh grip has longer leads at the pulling eye to facilitate pulling the cable up through the top, a very low profile lug and eye to slip through tight areas, and short shoulders to protect the cable while maintaining the slim profile. The grip can be used to pull cable overhead as well as underground through conduit and duct. It easily mates with a swivel and has the necessary strength to securely make pulls.

Application Information

• Prior to pulling cable, follow cable manufacturers’ cable preparation recommendations.
• Never exceed cable manufacturers’ pulling tension recommendations.
• Never use grips to approximate breaking strength safety factor of 5 recommended. Pulling Grips for Other Outside Plant Cables, Swivel Eye, Flexible Eye, Split Style, Low Profile Kellems Pulling Grips for fiber optic cable are made of high strength galvanized steel strand. They feature a multiweave mesh, with one-half the mesh length double weave, and the second half single weave. This special weave provides positive holding power while allowing the grip to remain flexible with no damage to the cable jacket. Added features include a steel nose cone which protects the cable end and allows the grip to pass easily through conduit and enclosures. The eye connects easily to a swivel or a pulling line. Several grip sizes are available to accommodate all diameters of fiber optic cable. Application Kellems Flexible Eye Pulling Grips for fiber optic cable are used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures. They will fit single cables or cable bundles, are easily installed on the cable, and are reusable. Benefits
• High strength multiweave mesh for positive holding power.
• Highly flexible mesh to follow the pulling path of the cable.
• Steel nose cone reduces snags and hang-ups and protects cable end.
• Easily installed and removed.
• A dependable, reusable pulling tool. Kellems® Wire Management Products Technical Information Fiber Optic Pulling Grips

www.hubbell-wiring.comV-54 Wiring Device-Kellems Support Grips for Fiber Optic Cable Kellems Support Grips for fiber optic cable are specially designed to hold the cable weight as it hangs in a vertical or horizontal position. Fiber optic cable must be supported and Kellems Grips provide the support easily and economically. These grips are made of high grade, non-magnetic tin-coated bronze strand. They are offered in universal bale or single eye configurations and are available in either closed mesh (for use where the cable end is available) or in split mesh, rod closing (for installation on existing cable runs or at specific locations). Split Support Grip Rod Closing Instructions The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the mesh pass around the rod and match up with the strands from the opposite direction. The rod does not touch the cable at any point and therefore cannot cut the cable. Rod Closing Grips are reusable. They may be removed and reused as many times as desired. Fast to Install Step 1 Wrap the grip around the cable and thread the rod through the preformed loops with a corkscrew motion, using the curved end of the rod to engage the loops. Step 2 The action required is a steady push and twist simultaneously. The fingers of the left hand are used to bring the loops together just ahead of the hook on the end of the rod. Step 3 To remove, simply pull the rod out. Kellems® Wire Management Products Technical Information Fiber Optic Support Grips

V-55www.hubbell-wiring.com Wiring Device-Kellems Types of Attachment The five attachment methods shown below provide unlimited flexibility of attachment to meet any condition. Type E Double Eye Grip, used where fastening is made with eyebolts or similar anchor terminations. Type A Single Eye Grip, used where fastening MUST be made from one point. Type U Universal Bale Grip, used to fasten around a structure or closed eye. Type Y Threaded bolt (⁵⁄₁₆-18 x 1½" long), used to fasten through drilled holes in plate. Type F Split fitting to fit AN-818 nuts. Fitting is positioned over nut and located with internal flange. A hose clamp is furnished and required to hold the fitting in correct position. Kellems® Wire Management Products Hose Containment Grips Note: It should be emphasized that Kellems® Hose Containment Grips are not to be used as a pressure reinforcing device for hose systems. These grips are custom made. Consult Technical Services for details. Kellems Hose Containment Grips are used on high pressure, flexible hose lines to prevent the hose from whipping violently in the event of hose failure at the fitting. These grips will prevent serious injury to personnel and damage to equipment by holding the hose in place in the event of hose failure. Kellems patented Hose Containment Grips are made of stainless steel with double weave mesh construction for high strength and come complete with hose clamps. Kellems Hose Containment Grips are supplied in diameters, length and attachments to meet individual requirements. Contact the Wiring Device-Kellems factory for specific information. These grips help meet OSHA Federal Register 1926-302 (b), 1926-603 (9), (10), JIC H-1-1973 (H13.11) and JIC P-1-1975 (P11.34) requirements. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-41 to V-42.

www.hubbell-wiring.comV-56 Wiring Device-Kellems Strain Relief System Selection Chart Grip Type Application Features Cord or Conduit Range Inches (cm) Type Fitting or Attachment Page Number Deluxe Cord Aluminum Fitting/ Stainless Steel Grip Outdoors or indoors where subjected to moisture or splash. Examples are crane and hoist pendant drop stations, hand tools, pumps and processing equipment. Aluminum fittings, stainless steel mesh, neoprene oil-and- watertight bushing. Double-single weave. .187"-3.250" (.47-8.25) NPT, PG, and metric aluminum, male straight, 45° male, 90° male, female straight. Thread sizes ³⁄₈"-3". V-58, V-59, V-62 Deluxe Cord Nylon Fitting/ Stainless Steel Grip Outdoors or indoors where subjected to moisture or splash. Examples are marine and food processing equipment. Nylon fitting, stainless steel mesh, double-single weave, neoprene oil-and- watertight bushing. .187"-1.125" (.47-2.86) NPT nylon, male straight, 90° male. Thread sizes ½"-1". V-60 Deluxe Cord Nylon Fitting/ Non-metallic Grip Indoor or outdoors. Provides liquidtight seal, where exposed to moisture. Excellent for oil refining and chemical processing. Non-metallic grip is corrosion resistant, nonconductive and provides superior grip- ping and flexing benefits. Neoprene liquidtight bushing. Nylon fitting. .187"-1.000" (.47-2.54) NPT nylon, straight male, thread sizes ³⁄₈"-1" 90° male, thread sizes ½"-1". V-61 Deluxe Cord Stainless Steel Fitting And Grip Indoor or outdoor use where exposed to moisture. Very strong for heavy abuse areas such as drilling platforms, steel mills and mines. Stainless steel fitting and grip for strength. Neoprene liquidtight bushing. Double/single weave grip. .187"-1.000" (.47-2.54) Straight male Only with NPT Thread sizes ½"-1". V-61 Dust-Tight Strain Relief Indoor use only for wiring of electrical enclosures, machine tools, portable power tools, bus drop cable systems. Neoprene gasket–seals out chips, dirt, dust. One piece design with galvanized steel mesh. Insulating bushing available. Zinc-plated steel locknut. .240"-2.450" (.61-6.22) Straight male NPS or NPT V-63 Liquidtight Flexible Conduit Grip (Metal and Non-Metallic) Wiring of machine tools, electrical enclosures, motors and systems where metallic liquidtight flexible conduit is subjected to vibration, flexure, motion or strain. Stainless steel mesh, liquidtight fittings. Sealing “O" rings (optional). Choice of fittings. .375"-4.000" trade sizes NPT ½"-4", Hubbell fittings, Male straight, 45° male, 90° male, female straight. V-66, V-67 Liquidtight Flexible Conduit Grip (UL Type A) Wiring or machine tools, electrical enclosures, motors and systems where conduit is subject to vibration and strain. Stainless steel mesh, liquidtight fittings with “O" ring and locknut. .375"-2.008" trade size male NPT steel, Hubbell fittings, straight male, 90° Thread sizes ½"-2". V-68 Kellems® Wire Management Products Strain Relief System Selection Chart Strain Relief Grips Kellems Strain Relief Grips are designed to prevent tension from being transmitted to joints and terminals on electrical cord, cable and conduit. In most applications, a Kellems grip for strain relief is stronger than the cable itself and gives much greater security than the use of a fitting alone. Kellems Grips for strain relief help make electrical systems safer, and save money by minimizing downtime from costly electrical failure due to cable pull-out. Kellems Grips also aid in compliance with the National Electric Code’s terminal tension protection requirements. Select the Correct Grip for Strain Relief Kellems Grips for strain relief are designed to fit on electrical cord, cable or flexible conduit. Step 1 Refer to the chart below to determine the grip style best suited for your application. Step 2 Determine your cable outside diameter or conduit size. Step 3 Locate environment—indoors or outdoors. Step 4 Decide if a liquidtight seal is required. Step 5 Select NPT size and fitting style.

V-57www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Strain Relief for Flexible Cords For Insulated Cables and Flexible, Liquidtight Conduits Endless weave provides easy cable/flexible conduit installation Stainless steel mesh is corrosion resistant. Can be used inside or outside. It eliminates cable or flexible conduit pull out and reduces costly downtime Multiweave grip gives cable arc-of-bend control minimizing cable damage and extending cable life. It is the strongest strain relief device available. Meets and exceeds all code requirements; prevents cable/conduit pull-out A liquidtight fitting is available with both cable and conduit fittings; prevents liquids from running through the fitting into the enclosure An NPT and PG threaded body allows easy attachment to either threaded hub or knock-out in box

www.hubbell-wiring.comV-58 Wiring Device-Kellems Kellems® Wire Management Products Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Straight Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number ³⁄₈ .250"-.312" .312"-.375" .375"-.437" (.63-.79) (.79-.95) (.95-1.11) 07401001 07401002 07401003 .187"-.250" .250"-.375" .375"-.500" .500"-.625" (.47-.63) (.63-.95) (.95-1.27) (1.27-1.59) 07401004 07401006 07401008 07401010 ½ .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F3 074011247* 074011248* .187"-.250" .250"-.375" .375"-.500" .500"-.625" (.47-.63) (.63-.95) (.95-1.27) (1.27-1.59) 07401011 07401013 07401015 07401017 ¾ .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F3 07401018 074011249* .375"-.500" .500"-.625" .625"-.750" .750"-.875" .875"-1.000" 1.000"-1.125" (.95-1.27) (1.27-1.59) (1.59-1.90) (1.90-2.22) (2.22-2.54) (2.54-2.86) 074011195 07401019 07401021 07401023 07401025 074011250* 1 1.125"-1.250" 1.250"-1.375" (2.86-3.17) (3.17-3.49) F5 074011028* 074011029* .750"-.875" .875"-1.000" 1.000"-1.125" 1.125"-1.250" 1.250"-1.375" (1.90-2.22) (2.22-2.54) (2.54-2.86) (2.86-3.17) (3.17-3.49) 074011251 07401026 07401027 07401028 074011178* .750"-.875" .875"-1.000" 1.000"-1.125" 1.125"-1.250" 1.250"-1.375" (1.90-2.22) (2.22-2.54) (2.54-2.86) (2.86-3.17) (3.17-3.49) 074011252 07401029 07401030 07401031 07401032 1.312"-1.437" 1.437"-1.562" 1.562"-1.687" 1.687"- 1.812" 1.750"-1.875" (3.33-3.65) (3.65-3.97) (3.97-4.28) (4.28-4.60) (4.44-4.76) 074011253 074011254* 074011255* 074011256* 074011257* 1.250"-1.375" 1.312"-1.437" 1.437"-1.562" 1.562"-1.687" 1.687"-1.812" 1.750"- 1.875" (3.17-3.49) (3.33-3.65) (3.65-3.97) (3.97-4.28) (4.28-4.60) (4.44-4.76) 074011258 074011259 07401033 07401034 07401035 074011260 1.812"-1.937" 1.937"-2.062" 2.062"-2.187" 2.187"-2.312" 2.312"-2.437" (4.60-4.92) (4.92-5.24) (5.24-5.55) (5.55-5.87) (5.87-6.19) 074011261 074011262* 074011263* 074011264* 074011265* 1.688"-1.812" 1.812"-1.937" 1.937"-2.062" 2.062"-2.187" 2.187"-2.312" 2.312"-2.437" (4.29-4.60) (4.60-4.92) (4.92-5.24) (5.24-5.55) (5.55-5.87) (5.87-6.19) 074011030 074011031 074011032 074011033 074011034 074011266* 1.937"-2.062" 2.062"-2.187" 2.187"-2.312" 2.312"-2.437" (4.92-5.24) (5.24-5.55) (5.55-5.87) (5.87-6.19) 074011036 074011037 074011038 074011039 2.437"-2.625" 2.625"-2.812" 2.812"-3.000" 3.000"-3.250" (6.19-6.67) (6.67-7.14) ( 7.14-7.62) ( 7.62-8.25) 074011186 074011187 074011188 074011189* Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III *Cable jacket may have to be stripped to pass through connector body. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

V-59www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Straight Female Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number ½ .375"-.500" .500"-.625" (.95-1.27) (1.27-1.59) 07401043 07401045 90° Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number ³⁄₈ .250"-.312" .312"-.375" .375"-.437" (.63-.79) (.79-.95) (.95-1.11) 07401071 07401072 07401073 .187"-.250" .250"-.375" .375"-.500" .500"-.625" (.47-.63) (.63-.95) (.95-1.27) (1.27-1.59) 07401074 07401076 07401078 07401080* .375"-.500" .500"-.625" .625"-.750" .750"-.875" (.95-1.27) (1.27-1.59) (1.59-1.90) (1.90-2.22) 07401081 07401083 07401084* 074011275* .500"-.625" .625"-.750" .750"-.875" .875"-1.000" 1.000"-1.125" (1.27-1.59) (1.59-1.90) (1.90-2.22) (2.22-2.54) (2.54-2.86) 07401085 07401087 07401089 07401091* 074011229* .750"-.875" .875"-1.000" 1.000"-1.125" 1.125"-1.250" (1.90-2.22) (2.22-2.54) (2.54-2.86) (2.86-3.17) 074011230 07401137 07401108 074011042* 1.000"-1.125" 1.125"-1.250" 1.250"-1.375" (2.54-2.86) (2.86-3.17) (3.17-3.49) 074011045 074011046 074011047 1.312"-1.437" 1.437"-1.562" 1.687"-1.812" 1.750"-1.875" (3.33-3.65) (3.65-3.97) (4.28-4.60) (4.44-4.76) 074011233 074011244 074011246 074011234* 45° Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number .250"-.375" .375"-.500" .500"-.625" (.63-.95) (.95-1.27) (1.27-1.59) 074011236 074011021 074011237* .500"-.625" .625"-.750" .750"-.875" (1.27-1.59) (1.59-1.90) (1.90-2.22) 074011049 074011051* 074011239* .625"-.750" .750"-.875" .875"-1.000" (1.59-1.90) (1.90-2.22) (2.22-2.54) 074011055 074011057 074011199* 1¼ 1.000"-1.125" 1.125"-1.250" (2.54-2.86) (2.86-3.17) F5 074011059 074011060 Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of *Cable jacket may have to be stripped to pass through connector body. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

www.hubbell-wiring.comV-60 Wiring Device-Kellems Kellems® Wire Management Products Deluxe Cord Grips Nylon Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Straight Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number .187"-.250" .250"-.375" .375"-.500" .500"-.625" (.47-.63) (.63-.95) (.95-1.27) (1.27-1.59) 074011331 074011332 074011333 074011334* .375"-.500" .500"-.625" .625"-.750" .750"-.875" (.95-1.27) (1.27-1.59) (1.59-1.90) (1.90-2.22) 074011335 074011336 074011337 074011338* .625"-.750" .750"-.875" .875"-1.000" 1.000"-1.125" (1.59-1.90) (1.90-2.22) (2.22-2.54) (2.54-2.86) 074011341 074011342 074011343 074011344* 90° Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number .250"-.375" .375"-.500" .500"-.625" (.63-.95) (.95-1.27) (1.27-1.59) 074011346 074011347 074011348* .375"-.500" .500"-.625" .625"-.750" (.95-1.27) (1.27-1.59) (1.59-1.90) 074011349 074011350 074011351* Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of *Cable jacket may have to be stripped to pass through connector body. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

V-61www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Deluxe Cord Grips Nylon Fittings, Non-metallic Mesh, and Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Nylon Fittings Non-metallic Mesh, Liquidtight for Insulated Cables Straight Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number ³⁄₈ .187"-.250" .250"-.312" .312"-.375" (.47-.63) (.63-.79) (.79-.95) CG304NM CG305NM CG306NM .187"-.250" .250"-.375" .375"-.500" (.47-.63) (.63-.95) (.95-1.27) CG404NM CG406NM CG408NM .375"-.500" .500"-.625" .625"-.750" (.95-1.27) (1.27-1.59) (1.59-1.90) CG608NM CG610NM CG612NM .500"-.625" .625"-.750" .750"-.875" .875"-1.000" (1.27-1.59) (1.59-1.90) (1.90-2.22) (2.22-2.54) CG810NM CG812NM CG814NM CG816NM 90° Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number ½ .250"-.375" .375"-.500" (.63-.95) (.95-1.27) F2 CG40690NM CG40890NM .375"-.500" .500"-.625" .625"-.750" (.95-1.27) (1.27-1.59) (1.59-1.90) CG60890NM CG61090NM CG61290NM* 1 .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F4 CG81290NM CG81490NM Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight for Insulated Cables Straight Male Thread NPT Thread Size Inches Grip Diameter Range Inches (cm) Form Size Catalog Number .187"-.250" .250"-.375" .375"-.500" .500"-.625" (.47-.63) (.63-.95) (.95-1.27) (1.27-1.59) CG404SST CG406SST CG408SST CG410SST ¾ .375"-.500" .500"-.625" (.95-1.27) (1.27-1.59) F2 CG608SST CG610SST ¾ .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F3 CG612SST CG614SST .500"-.625" .625"-.750" .750"-.875" .875"-1.000" (1.27-1.59) (1.59-1.90) (1.90-2.22) (2.22-2.54) CG810SST CG812SST CG814SST CG816SST Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the *Cable jacket may have to be stripped to pass through connector body. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

www.hubbell-wiring.comV-62 Wiring Device-Kellems Straight PG* Male Thread Hub Size Cord Diameter Range Inches (cm) Form Size Catalog Number PG16 .500"-.625" (1.27-1.59) F2 074PG16010 PG21 .500"-.625" (1.27-1.59) F2 074PG21010 PG21 .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F3 074PG211247 074PG211248 PG29 .625"-.750" .750"-.875" .875"-1.000" (1.59-1.90) (1.90-2.22) (2.22-2.54) 074PG29021 074PG29023 074PG29025 PG29 1.125"-1.250" (2.86-3.17) F5 074PG291028* PG36 1.125"-1.250" (2.86-3.17) F5 074PG36028* Note: *Panzergewinde. Straight Metric Male Thread Hub Size Cord Diameter Range Inches (cm) Form Size Catalog Number M20 .500"-.625" (1.27-1.59) F2 074M20010 M25 .625"-.750" .750"-.875" (1.59-1.90) (1.90-2.22) F3 074M251247 074M251248 M25 .500"-.625" (1.27-1.59) F2 074M25017 M32 .625"-.750" .750"-.875" .875"-1.000" (1.59-1.90) (1.90-2.22) (2.24-2.54) 074M32021 074M32023 074M32025 M32 1.000"-1.125" 1.125"-1.250" (2.54-2.86) (2.86-3.17) F5 074M321250 074M321028 Note: Kellems® Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the *Cable jacket may have to be stripped to pass through connector body. Kellems® Wire Management Products PG and Metric Threaded Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Specifications Material Temperature Range Aluminum (Body) Stainless Steel (Mesh) Neoprene (Bushings) Hazardous Locations Suitable for use in hazardous locations per Class I Div. 2, Approvals Deluxe Cord Grips UL Listed in accordance with Standard 514B for indoor/outdoor use. UL Control numbers 898D and 899D. Wet Locations Suitable for use in wet locations when used with a listed sealing ring between box and fitting. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

V-63www.hubbell-wiring.com Wiring Device-Kellems Non-Insulated, Wide Range Strain Relief Thread Size Cable Diameter Range Inches (cm) Mesh Length @ Nom. Dia. Inches (cm) Catalog Number Note: *Panzergewinde. Insulated, Wide Range Strain Relief with Insulating Bushing Thread Size Cable Diameter Range Inches (cm) Mesh Length @ Nom. Dia. Inches (cm) Dim. A Inches (cm) Min. Space Between Grips Inches (cm) Catalog Number Kellems® Wire Management Products Dust-Tight Strain Relief Grips Aluminum Fittings, Galvanized Steel Mesh, for Insulated Cables IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

www.hubbell-wiring.comV-64 Wiring Device-Kellems E M Application Kellems® I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip® plugs and connector bodies. The eye tabs fit under the nylon cord clamp and the screws slide through the eyelets, securing the grip in place. These grips are for indoor use only. Benefits

• Easily attached to Insulgrip plugs and connector bodies.
• Controls cable arc-of-bend.
• Provides heavy-duty strain relief.
• Fits all sizes. Kellems® Wire Management Products I-Grips Plastic-Coated, Galvanized Steel Mesh for Insulated Cables I-Grips Cable Diameter Range Inches (cm) E Inches (cm) M Inches (cm) Catalog Number Note: E-Eye length. M-Mesh length at nominal diameter. Eyelet hole diameter .203" (.52cm). I-Grips should not be used on Insulgrip devices when “Seal-Tite ®” weatherproof covers are to be installed. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-69 to V-76.

V-65www.hubbell-wiring.com Wiring Device-Kellems Thread Adapters for Multi-Pin Connectors Kellems® Thread Adapters are devices formatting AN-MS connectors and other multi-pin connectors to Kellems grips with NPT threaded fittings. They are made of aluminum with internal threads and replace the connector cord clamp. These adapters permit the installation of Kellems Grips, to prevent cable or conduit pull-out and control arc-of-bend.

Applications

Thread adapters allow the installation of Kellems® Grips on multi-pin connectors at electrical consoles, mobile equipment, control switches, assembly equipment and testing machines. Benefits

• Easy installation.
• Allows the use of Kellems grips.
• Extends connector and cable life. Kellems® Wire Management Products Thread Adapters for Multi-Pin Connectors Aluminum Thread Adapters for Multi-Pin Connectors Thread Adapters Deluxe Cord Grips Strain Relief Grips Liquidtight Conduit Grips (Insulated Throat) AN-MS Connector Size AN-MS Cable Clamp Number* Thread Size A Inch NPT Thread Size B Catalog Number Cable Diameter Range Inches (cm) Catalog Number Cable Diameter Range Inches (cm) Catalog Number Catalog Number 8S, 10S 10SL, 12, 12S 14, 14S 3057-3 3057-4 3057-6 ½" x 28" ⁵⁄₈" x 24" ¾" x 20" ³⁄₈ 091041000 091041001 091041002 07401001 07401002 07401003 — — 14, 14S 16, 16S 3057-6 3057-8 3057-10 ¾" x 20" ⁷⁄₈" x 20" 1" x 20" 091041003 091041004 091041006 07401004 07401006 07401008 07401010* 073031200 073031201 073031202 074093512 16, 16S 20, 22 3057-8 3057-10 3057-12 ⁷⁄₈" x 20" 1" x 20" 1³⁄₁₆" x 18" ¾ 091041005 091041007 091041008 07401011 07401013 07401015 07401017 07401018 .54"-.74" (1.37-1.85) 073031203 074093513 20, 22 24, 28 3057-12 3057-16 3057-20 3057-24 1³⁄₁₆" x 18" 1⁷⁄₁₆" x 18" 1¾" x 18" 2" x 18" 091041009 091041010 091041012 091041015 074011195 07401019 07401021 07401023 07401025 .73"-.97" (1.85-2.46) 073031204 074093514 24, 28 3057-16 3057-20 3057-24 1⁷⁄₁₆" x 18" 1¾" x 18" 2" x 18" 091041011 091041013 091041016 074011251 07401026 07401027 07401028 .97"-1.25" (2.46-3.17)073031205 074093515 3057-20 3057-24 3057-28 1¾" x 18" 2" x 18" 2¼" x 16" 091041014 091041017 091041019 07401029 07401030 07401031 07401032 — 074093516 Note: *Cable jacket may have to be stripped to pass through connector body. Number stamped on connector shell. *Number stamped on clamp shell. Example Thread Adapter 091041006

www.hubbell-wiring.comV-66 Wiring Device-Kellems Benefits

• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime. Kellems® Wire Management Products Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff® I Non-Metallic Conduit Straight With Male Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) ³⁄₈ ½ 3" ( 7.62) 074093511 074093401 ½ ½ 3.5" (8.89) 074093512 074093402 ¾ ¾ 4" (10.16) 074093513 074093403 1 1 5" (12.70) 074093514 074093404 1¼ 1¼ 6" (15.24) 074093515 074093405 1½ 1½ 6.75" (17.14) 074093516 074093406 2 2 8" (20.32) 074093518 074093408 2½ 2½ 9.75" (24.76) 074093520 074093410 3 3 11" (27.94) 074093522 074093412 4 4 14" (35.56) 074093526 — 90° Angle With Male Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) ³⁄₈ ½ 3" ( 7.62) 074093541 074093421 ½ ½ 3.5" (8.89) 074093542 074093422 ¾ ¾ 4" (10.16) 074093543 074093423 1 1 5" (12.70) 074093544 074093424 1¼ 1¼ 6" (15.24) 074093545 074093425 1½ 1½ 6.75" (17.14) 074093546 074093426 2 2 8" (20.32) 074093548 074093428 2½ 2½ 9.75" (24.76) 074093550 — 3 3 11" (27.94) 074093552 — Note: For use with Liquidtight Metal conduit and PolyTuff® I Non-Metallic conduit. IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-74 to V-76.

V-67www.hubbell-wiring.com Wiring Device-Kellems Straight With Chase Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number ½ ½ 3.5" (8.89) 07406079 ¾ ¾ 4" (10.16) 07406080 1 1 5" (12.70) 07406081 1¼ 1¼ 6" (15.24) 07406082 1½ 1½ 6.75" (17.14) 07406083 45° Angle With Male Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) ³⁄₈ ½ 3" ( 7.62) 074093561 074093441 ½ ½ 3.5" (8.89) 074093562 074093442 ¾ ¾ 4" (10.16) 074093563 074093443 1 1 5" (12.70) 074093564 074093444 1¼ 1¼ 6" (15.24) 074093565 074093445 1½ 1½ 6.75" (17.14) 074093566 074093446 2 2 8" (20.32) 074093568 074093448 Note: For use with Liquidtight Metal conduit and PolyTuff® I Non-Metallic conduit. Kellems® Wire Management Products Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff® I Non-Metallic Conduit IMPORTANT Read all breaking strength, safety and technical data relating to this product. Pages V-74 to V-76.

www.hubbell-wiring.comV-68 Wiring Device-Kellems Kellems® Wire Management Products Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for UL Type A Liquidtight Conduit Straight Male Hubbell Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number ³⁄₈ ½ 3.75" (9.52) H038CNK ½ ½ 4.5" (11.43) H050CNK ¾ ¾ 6.25" (15.87) H075CNK 1 1 7.5" (19.05) H100CNK 1¼ 1¼ 9" (22.86) H125CNK 1½ 1½ 13.5" (34.29) H150CNK 2 2 14.5" (36.83) H200CNK 90° Male Hubbell Fitting Conduit Trade Size Inches NPT Fitting Size Inches Mesh Length Inches (cm) Catalog Number ³⁄₈ ½ 3.75" (9.52) H0389CNK ½ ½ 4.5" (11.43) H0509CNK ¾ ¾ 6.25" (15.87) H0759CNK 1 1 7.5" (19.05) H1009CNK 1¼ 1¼ 9" (22.86) H1259CNK 1½ 1½ 13.5" (34.29) H1509CNK 2 2 14.5" (36.83) H2009CNK IMPORTANT Read all breaking strength, safety and technical data relating to this product. Page V-76

V-69www.hubbell-wiring.com Wiring Device-Kellems Wire Mesh Grip Materials Material Features Product Group Galvanized steel wire • High strength • Strain relief grips

• Not subject to continuous outside environment • I-Grips Stainless steel wire • High strength • Deluxe cord grips (302/304) • Corrosion resistant • Liquidtight, flexible, metal conduit grips
• Slightly magnetic • UL type A conduit grips Non-metallic strand • Superior flex life • Non-metallic deluxe cord grips
• Non-conductive
• Corrosion resistant
• Moderate strength Kellems® Wire Management Products Technical Information Strain Relief Grips Operating Temperatures Material Temperature Range Aluminum –40°F to +300°F (–40°C to +149°C). Aluminum Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C). Non-Metallic Deluxe Cord Grips –30°F to +225°F (–34°C to +107°C). Nylon –40°F to +225°F (–40°C to +107°C). Nylon Fitting with Stainless Steel Mesh –40°F to +225°F (–40°C to +107°C). Stainless Steel –60°F to +1000°F (–51°C to +537°C). Stainless Steel Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C). Neoprene (Bushings) –30°F to +240°F (–34°C to +115°C). Hazardous Locations Product Categories The product categories listed to the right are suitable Deluxe cord grip, aluminum fitting; for use in hazardous locations per Class I Div. 2, Deluxe cord grip, nylon fitting; Class II Div. 1 & 2, Class III Div. 1 & 2. Deluxe cord grip, non-metallic; Sealtite conduit grips; Dustight strain relief grips. Flammability Non-metallic deluxe cord grips will not support combustion. Listed below are the ratings. Component Rating Mesh grip UL 94HB. Fitting UL 94V-2. Approvals UL Listing and CSA Certification are indicated on appropriate product catalog pages. Agency UL Control Number Underwriters Laboratories Inc. 898D and 899D. UL Listed in accordance with Standard 514B for indoor/outdoor use. Wet Locations Product Categories The products noted to the right are suitable Deluxe cord grip, aluminum fitting; for use in wet locations when a listed sealing Deluxe sealing ring cord grip; ring is used between box and fitting. Deluxe cord grip, non-metallic; Sealtite conduit grips; Hubbell non-metallic conduit grips; Cord connectors; Hubbell Juniors; PolyTuff® connectors; Hubbell sealtite conduit connectors.

www.hubbell-wiring.comV-70 Wiring Device-Kellems Kellems® Wire Management Products Technical Information Strain Relief Grips Form Size Definition The term “Form Size” refers to the physical mass or overall dimensions of a cord connector. Form 1 is the smallest size, Form 8 is the largest size. Knockout Holes NPT Hub Size Knockout Hole Recommended Inches Min. to Max. Inches (cm) Product Data Deluxe Cord Grips, Liquidtight for Insulated Cables Deluxe Cord Grips helps to alleviate pull tension on terminals, control cable arc-of-bend, prevent cord pull-out, and provide a liquidtight seal. They are offered with either aluminum, stainless steel or nylon fittings in a variety of configurations and NPT thread sizes. Additionally, a completely non-metallic product is offered on page V-61. Application Deluxe Cord Grips are used indoors or outdoors to help prevent cord pull-out, and where cables are subjected to moisture, splash or submersion. Specific uses are: wiring enclosures, pendant stations, hand tools, construction, processing and material handling equipment, pumps, motors and machine tools. Benefits

• Helps to prevent cable pull-out.
• Controls cable arc-of-bend.
• Provides a liquidtight seal.
• Corrosion resistant stainless steel mesh with aluminum collar.

V-71www.hubbell-wiring.com Wiring Device-Kellems A (Overall) B Ref. C D F E Deluxe Cord Grips Fitting Dimensions Straight Hubbell Connectors Aluminum, Inches (cm) Nylon, Inches (cm) Stainless Steel, Inches (cm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E A Dia. B Ref. C D Throat Dia. E A B Ref. C D Throat Dia. E ³⁄₈-18 1 .88" (2.24) .90" (2.29) .46" (1.17) .44" (1.12) .99" (2.51) .88" (2.24) 1.00" (2.54) 1.10" (2.79) .43" (1.09) .45" (1.14) 1.00" (2.54) .93" (2.36) 1.01" (2.57) .88" (2.24) .90" (2.29) .46" (1.17) .45" (1.14) .87" (2.21) .75" (1.90) ½-14 1 .88" (2.24) .90" (2.29) .46" (1.17) .44" (1.12) .99" (2.51) .88" (2.24) 1.00" (2.54) 1.10" (2.79) .43" (1.09) .45" (1.14) 1.00" (2.54) .93" (2.36) ½-14 2 1.13" (2.87) 1.10" (2.79) .55" (1.40) .64" (1.63) 1.11" (2.82) 1.00" (2.54) 1.32" (3.35) 1.50" (3.81) .53" (1.35) .58" (1.47) 1.25" (3.17) 1.12" (2.84) 1.30" (3.30) 1.13" (2.87) 1.10" (2.79) .54" (1.37) .63" (1.60) 1.16" (2.95) 1.00" (2.54) ½-14 3 1.38" (3.51) 1.50" (3.81) .55" (1.40) .64" (1.63) 1.40" (3.56) 1.25" (3.17) ¾-14 2 1.13" (2.87) 1.10" (2.79) .55" (1.40) .64" (1.63) 1.29" (3.28) 1.13" (2.87) ¾-14 3 1.38" (3.51) 1.50" (3.81) .55" (1.40) .82" (2.08) 1.40" (3.56) 1.25" (3.17) 1.56" (3.96) 1.60" (4.06) .55" (1.40) .77" (1.96) 1.44" (3.66) 1.31" (3.33) 1.59" (4.04) 1.38" (3.51) 1.30" (3.30) .56" (1.42) .81" (2.06) 1.44" (3.66) 1.25" (3.17) 1-11½ 4 1.75" (4.44) 1.60" (4.06) .71" (1.80) 1.02" (2.59) 1.81" (4.60) 1.62" (4.11) 1.88" (4.78) 1.75" (4.44) .70" (1.78) 1.01" (2.57) 1.84" (4.67) 1.63" (4.14) 2.02" (5.13) 1.75" (4.44) 1.40" (3.56) .70" (1.78) 1.03" (2.62) 1.88" (4.78) 1.63" (4.14) 1-11½ 5 2.31" (5.87) 1.70" (4.32) .66" (1.68) 1.01" (2.57) 2.28" (5.79) 2.00" (5.08) 1¼-11½ 5 2.31" (5.87) 1.70" (4.32) .74" (1.88) 1.26" (3.20) 2.28" (5.79) 2.12" (5.38) 1½-11 5 2.31" (5.87) 1.70" (4.32) .74" (1.88) 1.38" (3.51) 2.28" (5.79) 2.12 (5.38) 1½-11½ 6 3.00" ( 7.62) 2.20" (5.59) .75" (1.90) 1.50" (3.81) 2.97" ( 7.54) 2.75" (6.98) 2-11½ 6 3.00" ( 7.62) 2.20" (5.59) .80" (2.03) 1.92" (4.88) 3.24" (8.24) 3.00" ( 7.62) 2-11½ 7 3.85" (9.78) 2.70" (6.86) .88" (2.24) 1.94" (4.93) 4.05" (10.29) 3.75" (9.52) 2½-8 7 3.85" (9.78) 2.70" (6.86) 1.30" (3.30) 2.32" (5.89) 4.34" (11.02) 4.02" (10.21) 2½-8 8 4.75" (12.06) 2.70" (6.86) 1.25" (3.17) 2.38" (6.05) 4.86" (12.34) 4.50" (11.43) 3-8 7 3.85" (9.78) 2.70" (6.86) 1.30" (3.30) 2.54" (6.45) 4.34" (11.02) 4.01" (10.21) 3-8 8 4.50" (11.43) 2.70" (6.86) 1.38" (3.51) 3.00" ( 7.62) 4.86" (12.34) 4.50" (11.43) Note: *A/C— Across Corners; A/F—Across Flats. Dimensions shown are approximate and are subject to change without notice. Kellems® Wire Management Products Technical Information Strain Relief Grips

www.hubbell-wiring.comV-72 Wiring Device-Kellems Deluxe Cord Grips Fitting Dimensions 45° Hubbell Connectors Aluminum, Inches (cm) F NPT Inches Form A Ref. B Ref. C D Throat Dia. E G Dia. Across Comers Across Flats ½-14 2 2.00" (5.08) 1.90" (4.83) .550" (1.40) .560" (1.42) 1.270" (3.23) 1.110" (2.79) 1.125" (2.86) ¾-14 3 2.30" (5.84) 2.50" (6.53) .560" (1.42) .750" (1.90) 1.480" (3.76) 1.281" (3.25) 1.375" (3.49) 1-11½ 4 2.60" (6.60) 2.80" ( 7.11) .700" (1.78) 1.000" (2.54) 1.690" (4.29) 1.500" (3.81) 1.750" (4.44) 1¼-11½ 5 3.90" (9.91) 3.90" (9.91) .740" (1.88) 1.250" (3.17) 2.45" (6.22) 2.125" (5.40) 2.310" (5.87) 1½-11½ 5 3.90" (9.91) 3.90" (9.91) .740" (1.88) 1.500" (3.81) 2.45" (6.22) 2.125" (5.40) 2.310" (5.87) Dimensions shown are approximate and are subject to change without notice. Kellems® Wire Management Products Technical Information Strain Relief Grips 90° Hubbell Connectors Aluminum, Inches (cm) Nylon, Inches (cm) F NPT Inches Form A B Ref. C D Throat Dia. E G Dia. A B Ref. C D Throat Dia. E G Dia.A/C* A/F* A/C* A/F* ³⁄₈-18 1 1.27" (3.23) 2.00" (5.08) .460" (1.17) .440" (1.12) 1.15" (2.92) 1.10" (2.79) .875" (2.22) ½-14 2 1.56" (3.96) 2.30" (5.84) .500" (1.27) .546" (1.39) 1.30" (3.30) 1.13" (2.87) 1.125" (2.86) 1.41" (3.58) 2.50" (6.35) .550" (1.40) .575" (1.46) 1.23" (3.12) 1.12" (2.82) 1.315" (3.34) ¾-14 3 1.79" (4.55) 2.80" ( 7.11) .560" (1.42) .765" (1.94) 1.49" (3.78) 1.31" (3.33) 1.375" (3.49) 1.65" (4.19) 2.81" ( 7.14) .560" (1.42) .765" (1.94) 1.42" (3.61) 1.29" (3.28) 1.560" (3.96) 1-11½ 4 2.08" (5.28) 3.20" (8.13) .700" (1.78) 1.000" (2.54) 1.70" (4.32) 1.50" (3.81) 1.750" (4.44) 1.99" (5.05) 3.30" (8.38) .700" (1.78) 1.010" (2.57) 1.82" (4.62) 1.60" (4.06) 1.875" (4.76) 1¼-11½ 5 3.18" (8.08) 4.30" (10.92) .730" (1.85) 1.260" (3.20) 2.47" (6.27) 2.15" (5.46) 2.310" (5.87) 1½-11½ 5 3.18" (8.08) 4.30" (10.92) .750" (1.92) 1.500" (3.81) 2.47" (6.27) 2.15" (5.46) 2.310" (5.87) 2-11½ 6 3.51" (8.92) 5.50" (13.97) .800" (2.03) 1.920" (4.88) 2.98" ( 7.57 ) 2.78" ( 7.0 6) 3.000" ( 7.62) Note: *A/C - Across Corners; A/F - Across Flats. B Ref. A Ref. D C E F G B Ref. A D C E F G

V-73www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Technical Information Strain Relief Grips Dimensions shown are approximate and are subject to change without notice. A (Overall) B Ref. C (N.P.T. Thread Depth) D E F Product Data Dust-Tight Strain Relief Grips for Insulated Cables Kellems® Strain Relief Grips connect flexible cord or bus drop cable to electrical enclosures. For indoor use only, they are available with either insulated or non-insulated aluminum fittings, and feature single weave, galvanized steel mesh grips with patented wide range mesh construction. They come with a locknut and a neoprene gasket that provides a dust tight seal. Application Used to connect electrical cable to power boxes, cabinets, panel boards, power centers, machine tools and with bus drop systems. Benefits

• Helps prevent cord or cable pull-out. • Patented mesh construction.
• Provides a dust tight seal. • One piece design.
• Easy installation. I-Grips for Insulated Cables Kellems I-Grips are made of high strength, plastic coated galvanized steel strand. They are offered in six sizes to fit all cable diameters used with Hubbell Insulgrip ® Kellems l-Grips will control cable arc-of-bend and reduce high pull tensions from being transmitted to the wiring terminals. Application Kellems I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip plugs and connector bodies. The eye tabs fit under the nylon cord clamp and the screws slide through the eyelets, securing the grip in place. I-Grips can be used on any Insulgrip cord set which requires cable, arc-of-bend control or heavy duty strain relief. Cord sets used at in-door construction sites or for plant maintenance jobs are examples. These grips are for indoor use only. Benefits
• Easily attached to Insulgrip plugs and • Provides heavy duty strain relief. connector bodies. • Controls cable arc-of-bend.
• Fits all sizes. Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof covers are to be installed. Deluxe Cord Grips Fitting Dimensions Female Hubbell Connectors Aluminum, Inches (cm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E Across Comers Across Flats ³⁄₈-18 1 .88" (2.24) 1.40" (3.56) .560" (1.42) .44" (1.12) .94" (2.39) .81" (2.06) ½-14 2 1.13" (2.87) 1.80" (4.57) .560" (1.42) .63" (1.60) 1.15" (2.92) 1.00" (2.54) ¾-14 2 1.13" (2.87) 2.10" (5.33) .750" (1.90) .63" (1.60) 1.44" (3.66) 1.25" (3.17) 1-11½ 4 1.75" (4.44) 2.30" (5.84) .880" (2.24) 1.10" (2.79) 1.88" (4.78) 1.63" (4.14) 1¼-11½ 5 2.31" (5.87) 2.80" ( 7.11) .950" (2.41) 1.43" (3.63) 2.64" (6.71) 2.29" (5.82) 1½-11½ 5 2.31" (5.87) 2.80" ( 7.11) .950" (2.41) 1.43" (3.63) 2.64" (6.71) 2.29" (5.82)

www.hubbell-wiring.comV-74 Wiring Device-Kellems Kellems® Wire Management Products Technical Information Strain Relief for Liquidtight Conduit Strain Relief Grips for Liquidtight Flexible Metal and PolyTuff® I Non-Metallic Conduit Kellems Liquidtight, Flexible Metal Conduit Grips are offered with high quality Hubbell plated steel fittings in a wide variety of NPT sizes and configurations, either insulated or non-insulated. The addition of a stainless steel mesh to these fittings makes them stronger than the conduit itself. Kellems Conduit Grips helps prevent conduit pull-out from the connecting fitting that is subject to stress, pull tension, vibration, motion or strain. They promote safe electrical systems and reduce equipment downtime. Application Kellems Conduit Grips are used in the wiring of machine tools, motors, molding equipment, transformers, weaving and paper machines, fans, lighting, bakeries, breweries, food processing, chemical plants, dairies, mines and any application that requires Liquidtight Conduit. Benefits

• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
• Liquidtight fittings.
• Easily installed.
• Stainless steel grip resists corrosion. Kellems Conduit Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code. Hardened Steel Locknut has tangs that dig into box for excellent continuity of ground; locknut will not slip or spin Connectors with insulated throats protect insulation on wires during wire pulling. Yellow color easily seen by inspectors. 2½" - 4" sizes include insulating bushing instead of fixed insulator Steel grounding ferrule easily threaded by hand. Fits convolutions to conduit. Eliminates pullouts and insures continuity of ground; distortion free to remain reusable Nylon gland ring is split for ease of installation and greater compression. Reversible design cannot be installed facing the wrong way. Nylon is impervious to liquids, resistant to temperature extremes and resists abrasion Hexagonal compression nut is screw machined steel through 1" and malleable iron on larger sizes Optional Sealing Washer gives better liquidtight protection around knockout of sheet metal box. Neoprene gasket seals out liquids and steel retaining ring protects gasket from distortion; order separately Body is virtually unbreakable. Straight connectors through 1" are screw machine steel; other sizes malleable iron. Threads at left are tapered to insure liquidtight seal in threaded hub. Liquidtight conduit cutaway view shows flexible steel core under plastic jacket Wire mesh grip prevents pullout Liquidtight conduit cutaway view shows flexible steel core under plastic jacket

V-75www.hubbell-wiring.com Wiring Device-Kellems 45° Angle with Male Fitting with Insulated Throat Dimensions, Inches Trade Size Inches H J Ref. K L M Throat Dia. N Catalog NumberA/C* A/F* A/C* A/F* Kellems® Wire Management Products Technical Information Strain Relief for Liquidtight Conduit Dimensions shown are approximate and are subject to change without notice. Note: *A/C - Across Corners; A/F - Across Flats. J M Throat Dia. L K H N A/C A/F D Throat Dia. E A/C A/F C A Ref. B Ref. G O Throat Dia. E D F P A/C A/F 90° Angle with Male Fitting Dimensions, Inches Trade Size Inches D E F G Ref. O Throat Dia. P Catalog NumberA/C* A/F* A/C* A/F* 45° Angle with Male Fitting Dimensions, Inches Trade Size Inches H J Ref. K L M Throat Dia. N Catalog NumberA/C* A/F* A/C* A/F* Liquidtight Conduit Grip Fitting Dimensions, Inches Straight with Male Fitting Dimensions, Inches Trade Size Inches A Ref. B Ref. C D Throat Dia. E Catalog NumberA/C* A/F* A/C* A/F* Straight with Male Fitting with Insulated Throat Dimensions, Inches Trade Size Inches A Ref. B Ref. C D Throat Dia. E Catalog NumberA/C* A/F* A/C* A/F* 90° Angle with Male Fitting with Insulated Throat Dimensions, Inches Trade Size Inches D E F G Ref. O Throat Dia. P Catalog NumberA/C* A/F* A/C* A/F*

www.hubbell-wiring.comV-76 Wiring Device-Kellems Dimensional Charts For UL Type A, Liquidtight Conduit Grip Fittings Straight with Male Fitting with Insulated Throat Dimensions Inches (cm) Trade Size NPT Inches A B C D Catalog Number 90° Angle with Male Fitting with Insulated Throat Dimensions Inches (cm) Trade Size NPT Inches E F G H I Catalog Number C Flats A Ref. B Ref. D H I F E G Flats Steel Locknut has tangs that dig into box for excellent continuity of ground; locknut will not slip or spin Insulated throat protects insulation on wires during pulling; yellow color easily seen by inspectors Body is virtually unbreakable. Straight connectors through 1" are screw machine steel; other sizes are malleable iron. Threads are tapered to insure liquidtight seal when used in threaded hub; octagonal shape inside holds the ferrule to prevent conduit from twisting during installationNeoprene O-ring is factory assembled into the body to seal out liquids Wire mesh grip prevents pullout Yellow nylon ferrule fits inside non- metallic conduit to hold the shape; barb in designed to assure liquidtight seal even with non-square cut; ferrule is keyed to fit into body to prevent conduit twisting Hexagonal compression nut is machine steel through 1" malleable iron on larger sizes; tapered interior compresses sleeve over conduit sealing out liquids and preventing pullout Yellow nylon sleeve installs over conduit; six slits in sleeve permit tight compression onto conduit as compression nut is tightened Strain Relief for UL Type A, Flexible, Liquidtight Conduit Kellems Grips for UL Type A, non-metallic, flexible, liquidtight conduit are available in straight and 90° male and feature a high quality Hubbell plated steel or malleable iron fitting, complete with a sealing O-ring, lock nut and stainless steel mesh. These grips increase the retention of the conduit in the fitting, control its arc-of-bend and provide a liquidtight seal. Kellems® Wire Management Products Technical Information Strain Relief for Liquidtight Conduit Benefits

• Provides a liquidtight seal.
• Helps prevent conduit pull-out.
• Reduces conduit cutting, kinking, fraying and splitting at the fitting.
• Easily installed. Application These grips are used on UL Type A non-metallic conduit connections at limit switches, motor boxes, panel boards, control stations and on all types of machinery and machine tools.

www.hubbell-wiring.com Wiring Device-Kellems Hubbell has the broadest line and the widest choice of materials in the industry. NPT hub sizes from ¼" to 3" in straight male end, 90°, 45°, female and underground feed connectors. They are available in your choice of aluminum, plated steel, nylon and stainless steel. Hubbell offers a full line of machined aluminum cord connectors in NPT hub sizes ¼" through 1" and cast aluminum 1" to 3". They provide durable performance and a clean attractive look without adding unwanted weight. NPT hub sizes ¼" to 1" feature an attractive knurled finish which makes them easy to handle and maintain a U.L. listing by hand tightening. The zinc-plated steel cord connectors offers the strength of steel and the corrosion resistance of zinc-plating. These heavy-duty connectors hold up to most manufacturing chemicals including acid solutions, solvents and other corrosive materials. Their machined steel nut and body allows for tightening the compression nut and NPT hub without worrying about stripping the threads. For larger size cord, NPT hub sizes 1" to 2", Hubbell utilizes malleable iron connectors which provide excellent holding and liquidtight performance. Hubbell’s nylon cord connectors resist most common industrial corrosives and provide highly effective pullout protection in a lightweight design. They are ideal for any application where weight, conductivity or corrosion may be an issue. They’re available in NPT hub sizes from ¼" to 1". Stainless steel cord connectors provide superior strength and corrosion resistance for industrial and military applications. They are machined from 300 series stainless steel and come in ¼" to 1", NPT hub sizes. Kellems® Wire Management Products Cord Connectors Features and Benefits Lubricated neoprene bushing compresses easily for a liquidtight seal and added pull-out protection The connector body is a one-piece design with machined threads; a tapered interior seats the bushing evenly for a liquidtight seal Machined threads provide a strong positive seal; the tapered interior dome easily drives the bushing into the connector body The patented GOTCHA ® ring incorporates a split hinge design to prevent friction and provide strain relief, also color-coded for sizing identification

www.hubbell-wiring.comV-78 Wiring Device-Kellems Machined Aluminum Machined Zinc-Plated Steel Stainless Steel Gray Nylon Black Nylon Straight Male NPT Hub Size Cord Dia. Inches (mm) Form Size Color Code Machined Aluminum Machined Zinc-Plated Steel Stainless Steel Nylon Gray Nylon Black .06"-.13" (1.6-3.2) .13"-.19" (3.2-4.7) .19"-.25" (4.7-6.3) .25"-.31" (6.3-7.9) .31"-.38" ( 7.9 -9.5) .38"-.44" (9.5-11) Green Orange Red Black White Blue SHC1002 SHC1003 SHC1004 SHC1005 SHC1003SS SHC1004SS SHC1001CR SHC1002CR SHC1003CR SHC1004CR SHC1005CR SHC1006CR SHC2005CR ³⁄₈ .06"-.13" (1.6-3.2) .13"-.19" (3.2-4.7) .19"-.25" (4.7-6.3) .25"-.31" (6.3-7.9) .31"-.38" ( 7.9 -9.5) .38"-.44" (9.5-11.0) Green Orange Red Black White Blue SHC1007 SHC1008 SHC1009 SHC1010 SHC1011 SHC1012 SHC1008ZP SHC1010ZP SHC1012ZP SHC1009SS SHC1011SS SHC1012SS SHC1008CR SHC1009CR SHC1010CR SHC1011CR SHC1012CR SHC2008CR SHC2010CR SHC2011CR SHC2012CR .19"-.25" (4.7-6.3) .25"-.31" (6.3-7.9) .31"-.38" ( 7.9 -9.5) .38"-.44" (9.5-11.0) Red Black White Blue SHC1015 SHC1016 SHC1017 SHC1018 .06"-.13" (1.6-3.2) .13"-.19" (3.2-.4.7) .19"-.25" (4.7-6.3) .25"-.38" (6.3-.9.7) .38"-.50" (9.7-12.7) .50"-.63" (12.7-15.9) Green Orange Red White Blue Brown SHC1019 SHC1020 SHC1021 SHC1022 SHC1023 SHC1024 SHC1020ZP SHC1021ZP SHC1022ZP SHC1023ZP SHC1024ZP SHC1020SS SHC1021SS SHC1022SS SHC1023SS SHC1024SS SHC1019CR SHC1020CR SHC1021CR SHC1022CR SHC1023CR SHC1024CR SHC2021CR SHC2022CR SHC2023CR SHC2024CR .38"-.50" (9.7-12.7) .50"-.63" (12.7-15.9) .63"-.75" (15.9-19.0) .75"-.88" (19.0-22.2) Blue Brown Yellow Orchid SHC1025 SHC1026 SHC1027 SHC1028 SHC1027ZP SHC1028ZP** Note: See pages V-87 to V-95 for technical information and dimensional drawings. *IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information. **Cable jacket may have to be stripped to pass through connector body. Locknuts sold separately. See page V-84 for additional information. Kellems® Wire Management Products Straight Male Cord Connectors Form Size 1-3 IP66* SUITABILITY UL Listed to Type 4, 4X, 12 and 13

V-79www.hubbell-wiring.com Wiring Device-Kellems Straight Male NPT Hub Size Cord Dia. Inches (mm) Form Size Color Code Machined Aluminum Machined Zinc-Plated Steel Stainless Steel Nylon Gray Nylon Black .06"-.13" (1.6-3.2) .13"-.19" (3.2-4.7) .19"-.25" (4.7-6.3) .25"-.38" (6.3-9.7) .38"-.50" (9.7-12.7) .50"-.63" (12.7-15.9) Green Orange Red White Blue Brown SHC1029 SHC1030 SHC1031 SHC1032 SHC1033 SHC1034 SHC1030ZP SHC1031ZP SHC1032ZP SHC1033ZP SHC1034ZP .38"-.50" (9.5-12.7) .50"-.63" (12.7-15.9) .63"-.75" (15.9-19.0) .75"-.88" (19.0-22.2) Blue Brown Yellow Orchid SHC1036 SHC1037 SHC1038 SHC1035ZP SHC1037ZP SHC1038ZP SHC1035SS SHC1036SS SHC1037SS SHC1038SS SHC1035CR SHC1036CR SHC1037CR SHC1038CR SHC2035CR SHC2036CR SHC2037CR SHC2038CR .50"-.63" (12.7-15.9) .63"-.75" (15.9-19.0) .75"-.88" (19.0-22.2) Brown Yellow Orchid SHC1097ZP SHC1098ZP SHC1099ZP .38"-.50" (9.7-12.7) .50"-.63" (12.7-15.9) .63"-.75" (15.9-19.0) .75"-.88" (19.0-22.2) .88"-1.00" (22.2-25.4) 1.00"-1.13" (25.4-28.6) Blue Brown Yellow Orchid Gray Pink SHC1039 SHC1040 SHC1041 SHC1042 SHC1043 SHC1044 SHC1043ZP SHC1041SS SHC1042SS SHC1043SS SHC1044SS SHC1039CR SHC1040CR SHC1041CR SHC1042CR SHC1043CR SHC1044CR SHC2040CR SHC2041CR SHC2042CR SHC2043CR SHC2044CR** Note: See pages V-87 to V-95 for technical information and dimensional drawings. *IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information. **Cable jacket may have to be stripped to pass through connector body. Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum. Locknuts sold separately. See page V-84 for additional information. Kellems® Wire Management Products Straight Male Cord Connectors Form Size 2-4 IP66* SUITABILITY UL Listed to Type 4, 4X, 12 and 13 Machined Aluminum Machined Zinc-Plated Steel Stainless Steel Gray Nylon Black Nylon

www.hubbell-wiring.comV-80 Wiring Device-Kellems Kellems® Wire Management Products Straight Male Cord Connectors Form Size 5-8 UL Listed to Type 4, 4X, 12 and 13 Cast Aluminum Cast Aluminum Malleable Iron Straight Male NPT Hub Size Cord Diameter Inches (mm) Form Size Cast Aluminum Malleable Iron .88"-1.00" 1.00"-1.13" 1.13"-1.25" 1.25"-1.38" (22.2-25.4) (25.4-28.6) (28.6-31.7) (31.7-34.9) SHC1046 SHC1047 SHC1048 SHC1049 .75"-.88" .88"-1.00" 1.00"-1.13" 1.13"-1.25" 1.25"-1.38" (19.0-22.2) (22.2-25.4) (25.4-28.6) (28.6-31.7) (31.7-34.9) SHC1050 SHC1051 SHC1052 SHC1053 SHC1054 SHC1052ZP SHC1053ZP SHC1054ZP .75"-.88" .88"-1.00" 1.00"-1.13" 1.13"-1.25" 1.25"-1.38" (19.0-22.2) (22.2-25.4) (25.4-28.6) (28.6-31.7) (31.7-34.9) SHC1055 SHC1056 SHC1057 SHC1058 SHC1059 SHC1057ZP SHC1058ZP SHC1059ZP 1.38"-1.50" 1.50"-1.63" 1.63"-1.75" 1.75"-1.88" (34.9-38.1) (38.1-41.3) (41.3-44.4) (44.4-47.6) SHC1061 SHC1062 SHC1063 SHC1064 1.25"-1.38" 1.38"-1.50" 1.50"-1.63" 1.63"-1.75" 1.75"-1.88" (31.7-34.9) (34.9-38.1) (38.1-41.3) (41.3-44.4) (44.4-47.6) SHC1065 SHC1066 SHC1067 SHC1068 SHC1069 1.69"-1.81" 1.81"-1.94" 1.94"-2.06" 2.06"-2.19" 2.19"-2.31" (42.9-46.0) (46.0-49.2) (49.2-52.4) (52.4-55.6) (55.6-58.7) SHC1070 SHC1071 SHC1072 SHC1073 SHC1074 1.69"-1.81" 1.81"-1.94" 1.94"-2.06" 2.06"-2.19" 2.19"-2.31" 2.31"-2.44" (42.9-46.0) (46.0-49.2) (49.2-52.4) (52.4-55.6) (55.6-58.7) (58.7-61.9) SHC1076 SHC1077 SHC1078 SHC1079 SHC1080 SHC1081 1.69"-1.81" 1.94"-2.06" 2.06"-2.19" 2.19"-2.31" 2.31"-2.44" (42.9-46.0) (49.2-52.4) (52.4-55.6) (55.6-58.7) (58.7-61.9) SHC1086 SHC1088 SHC1089 SHC1090 SHC1091 2.44"-2.63" 2.63"-2.81" 2.81"-3.00" 3.00"-3.25" (61.9-66.7) (66.7-71.4) (71.4-76.2) (76.2-82.5) SHC1092 SHC1093 SHC1094 SHC1095 Note: See pages V-87 to V-95 for technical information and dimensional drawings. *IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information. **Cable jacket may have to be stripped to pass through connector body. Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum. F5 and larger will not be color coded. Locknuts sold separately. See page V-84 for additional information. IP66* SUITABILITY

V-81www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products 45° and 90° Male Cord Connectors Form Size 1-6 UL Listed to Type 4, 4X, 12 and 13 45° Male NPT Hub Size Cord Diameter Inches (mm) Form Size Color Code Machined Aluminum† Machined Zinc-Plated Steel∆ Cast Aluminum .19"-.25" .25"-.38" .38"-.50" .50"-.63" (4.7-6.3) (6.3-9.7) (9.7-12.7) (12.7-15.9) Red White Blue Brown VHC1021 VHC1022 VHC1023 VHC1024 VHC1022ZP VHC1023ZP VHC1024ZP .38"-.50" .50"-.63" .63"-.75" (9.7-12.7) (12.7-15.9) (15.9-19.0) Blue Brown Yellow VHC1035 VHC1036 VHC1037 1 .63"-.75" .75"-.88" (15.9-19.0) (19.0-22.2) F4 Yellow Orchid VHC1041 VHC1042 1¼ 1.00"-1.13" 1.13"-1.25" (25.4-28.6) (28.6-31.7) F5 VHC1052 VHC1053 90° Male NPT Hub Size Cord Diameter Inches (mm) Form Size Color Code Machined Aluminum† Machined Zinc-Plated Steel∆ Nylon Gray Nylon Black Cast Aluminum ³⁄₈ .25"-.31" .31"-.38" .38"-.44" (6.3-7.9) ( 7.9 -9.5) (9.5-11.0) Black White Blue NHC1010 NHC1011 NHC1012 .06"-.13" .13"-.19" .19"-.25" .25"-.38" .38"-.50" .50"-.63" (1.6-3.2) (3.2-4.7) (4.7-6.3) (6.3-9.7) (9.7-12.7) (12.7-15.9) Green Orange Red White Blue Brown NHC1020 NHC1021 NHC1022 NHC1023 NHC1024 NHC1021ZP NHC1022ZP NHC1023ZP NHC1024ZP NHC1020CR NHC1021CR NHC1022CR NHC1023CR NHC1024CR NHC2022CR NHC2023CR NHC2024CR .38"-.50" .50"-.63" .63"-.75" .75"-.88" (9.7-12.7) (12.7-15.9) (15.9-19.0) (19.0-22.2) Blue Brown Yellow Orchid NHC1035 NHC1036 NHC1037 NHC1038 NHC1035ZP NHC1036ZP NHC1037ZP NHC1038ZP NHC1035CR NHC1036CR NHC1037CR NHC1038CR .50"-.63" .63"-.75" .75"-.88" .88"-1.00" 1.00"-1.13" (12.7-15.9) (15.9-19.0) (19.0-22.2) (22.2-25.4) (25.4-28.7) Brown Yellow Orchid Gray Pink NHC1040 NHC1041 NHC1042 NHC1043 NHC1044 NHC1041ZP NHC1041CR NHC1042CR NHC1043CR NHC2041CR NHC2042CR NHC2043CR .88"-1.00" 1.00"-1.13" 1.13"-1.25" 1.25"-1.38" (22.2-25.4) (25.4-28.6) (28.6-31.7) (31.7-34.9) NHC1051 NHC1052 NHC1053 NHC1054 1.00"-1.13" 1.13"-1.25" 1.25"-1.38" (25.4-28.6) (28.6-31.7) (31.7-34.9) NHC1057 NHC1059 Note: See pages V-87 to V-95 for technical information and dimensional drawings. *IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information. **Cable jacket may have to be stripped to pass through connector body. †Nuts are machined aluminum and bodies are cast aluminum. ∆Compression nuts are machined zinc-plated steel and bodies are zinc-plated malleable iron. Locknuts sold separately. See page V-84 for additional information. IP66* SUITABILITY

www.hubbell-wiring.com V-82 Wiring Device-Kellems Machined Aluminum Gray Nylon Machined Zinc-Plated Steel Machined Aluminum Machined Aluminum Straight Female NPT Hub Size Cord Diameter Inches (mm) Form Size Color Code Machined Aluminum ½ .25"-.38" .38"-.50" (6.3-9.7) (9.7-12.7) F2 White Blue FHC1022 FHC1023 ¾ .38"-.50" .50"-.63" (9.7-12.7) (12.7-15.9) F2 Blue Brown FHC1033 FHC1034 1 .75"-.88" .88"-1.00" (19.0-22.2) (22.2-25.4) F4 Orchid Gray FHC1042† FHC1043† Note: See pages V-87 to V-95 for technical information and dimensional drawings. *Cable jacket may have to be stripped to pass through connector body. †Nuts are machined aluminum and bodies are cast aluminum. Underground Feeder Connectors NPT Hub Size Cord Diameter Inches (mm) Wire Size UF** Machined Aluminum Machined Zinc-Plated Steel Nylon Gray Nylon Black ½ .2"x.4" min .25"-.55" max 5.1 x 10.2) (6.3 x 14.0) 2 # 1 2 # 12, 2 # 10. UFC0001 UFC0001ZP UFC0001CR UFC2001CR ¾ .2"x.4" min .25"-.55" max 5.1x10.2) (6.3x14.0) 2 # 1 2 # 12, 2 # 10. UFC0002 — — — ¾ .2"x.6" min .26"x.78" max 5.1x15.2) (6.6x19.8) 3 # 1 3 # 12, 3 # 10. UFC0003 — UFC0003CR UFC2003CR Note: See pages V-87 to V-95 for technical information and dimensional drawings. *IP66 Suitability when used with optional metal clad O-ring, see page V-84 for additional information. **Wire sizes vary among manufacturers. Locknuts sold separately, see page V-84 for additional information. Metric Aluminum Cord Connectors Metric Hub Size Cord Diameter Inches (mm) Form Size Catalog Number M16 .31"-.38" ( 7.9 -9.7 ) F1 SHCM161011 M20 .31"-.38" ( 7.9 -9.7 ) F1 SHCM201017 M20 .25"-.38" .38"-.50" .50"-.62" (6.3-9.7) (9.7-12.7) (12.7-15.8) SHCM201022 SHCM201023 SHCM201024 M25 .38"-.50" .50"-.62" (9.7-12.7) (12.7-15.8) F2 SHCM251033 SHCM251034 M30 .63"-75" (15.9-19.0) F3 SHCM301037 Note: †When used with metal clad O-ring, see page V-84 for additional information. Non-metallic Locknuts sold separately , see page V-84 for additional information. Kellems® Wire Management Products Straight Female, Underground Feeder and Metric Connectors Form Size 1-4 IP66* SUITABILITY UL Listed to Type 4, 4X, 12 and Type 13 †

V-83www.hubbell-wiring.com Wiring Device-Kellems SEC100BA SECP29GA LNP29BPK25 Low Profile NPT Cord Connectors NPT Hub Size Cord Diameter Inches (mm) Color Catalog Number Non-metallic Locknuts ³⁄₈ .18"-.31" (4.6 -7.9) Gray SEC38GA* 31622002LPK50 ³⁄₈ .18"-.31" (4.6 -7.9) Black SEC38BA* 31622002LPK50 ½ .17"-.45" (4.3-11.4) Gray SEC50GA 31622003LPK50 ½ .17"-.45" (4.3-11.4) Black SEC50BA 31622003LPK50 ¾ .45"-.71" (11.4-18.0) Gray SEC75GA 31622007LPK50 ¾ .45"-.71" (11.4-18.0) Black SEC75BA 31622007LPK50 1 .59"-1.00" (15-25.4) Gray SEC100GA 31622008LPK50 1 .59"-1.00" (15-25.4) Black SEC100BA 31622008LPK50 Note: See pages V-87 to V-95 for technical information and dimensional drawings. Catalog numbers with “PK50” suffix are bulk packed 50 pieces. Low Profile PG∆ Cord Connectors Hub Size Cord Diameter Inches (mm) Color Catalog Number Non-metallic Locknuts PG7 .11"-.25" (2.9-6.4) Gray SECP7GA* LNP7BPK100 PG7 .11"-.25" (2.9-6.4) Black SECP7BA* LNP7BPK100 PG9 .18"-.31" (4.6 -7.9) Gray SECP9GA* LNP9BPK100 PG9 .18"-.31" (4.6 -7.9) Black SECP9BA* LNP9BPK100 PG11 .23"-.40" (5.8-10.0) Gray SECP11GA* LNP11BPK100 PG11 .23"-.40" (5.8-10.0) Black SECP11BA* LNP11BPK100 PG16 .23"-.53" (5.8-13.5) Gray SECP16GA LNP16BPK100 PG16 .23"-.53" (5.8-13.5) Black SECP16BA LNP16BPK100 PG21 .45"-.71" (11.4-17.9) Gray SECP21GA LNP21BPK100 PG21 .45"-.71" (11.4-17.9) Black SECP21BA LNP21BPK100 PG29 .59"-.99" (15-25.2) Gray SECP29GA LNP29BPK25 PG29 .59"-.99" (15-25.2) Black SECP29BA LNP29BPK25 PG36 .88"-1.30" (22.2-32.0) Gray SECP36GA LNP36BPK25 PG36 .88"-1.30" (22.2-32.0) Black SECP36BA LNP36BPK25 Low Profile Metric Cord Connectors Hub Size Cord Diameter Inches (mm) Color Catalog Number Non-metallic Locknuts M12 .12"-.25" (2.9-6.4) Gray SECM12G LNM12BPK100 M12 .12"-.25" (2.9-6.4) Black SECM12B LNM12BPK100 M16 .11"-.31" (2.7-7.9) Gray SECM16G LNM16BPK100 M16 .11"-.31" (2.7-7.9) Black SECM16B LNM16BPK100 M20 .17"-.45" (4.3-11.4) Gray SECM20G* LNM20BPK100 M20 .17"-.45" (4.3-11.4) Black SECM20B* LNM20BPK100 M25 .49"-.71" (12.3-18.0) Gray SECM25G* LNM25BPK100 M25 .49"-.71" (12.3-18.0) Black SECM25B* LNM25BPK100 M32 .59"-1.00" (15.0-25.4) Gray SECM32G* LNM32BPK100 M32 .59"-1.00" (15.0-25.4) Black SECM32B* LNM32BPK100 M40 .87"-1.30" (22.0-32.0) Gray SECM40G LNM40BPK100 M40 .87"-1.30" (22.0-32.0) Black SECM40B LNM40BPK100 Note: See pages V-87 to V-96 for technical information and dimensional drawings. Catalog numbers above with “PK100” suffix, i.e. LNP7BPK100, are bulk packed 100 per carton. Catalog numbers above with “PK25” suffix, i.e. LNP29BPK25, are bulk packed 25 per carton. *Items indicated are UL recognized components. ∆Panzergewinde. Kellems® Wire Management Products Low Profile NPT, PG and Metric Thread Connectors Non-Metallic Cord Connectors IP66* SUITABILITY

www.hubbell-wiring.comV-84 Wiring Device-Kellems Kellems® Wire Management Products Accessories Cord Connector Parts NPT Hub Size Cord Diameter Inches (mm) Form Size Bushing Catalog Number Color Code GOTCHA® Ring Catalog Number ¼, ³⁄₈, ½ .062"-.125" .125"-.187" .187"-.250" .250"-.312" .312"-.375" .375"-.437" (1.58-3.17) (3.17-4.76) (4.76-6.35) (6.35 -7.93) ( 7.93-9.50) (9.50-11.1) 31518101BPK100 31518102BPK100 31518103BPK100 31518104BPK100 31518105BPK100 31518106BPK100 Green Orange Red Black White Blue 31648035GPK100 31648036GPK100 31648037GPK100 31648038GPK100 31605010GPK100 31648039GPK100 ½, ¾ .187"-.250" .250"-.375" .375"-.500" .500"-.625" (4.76-6.35) (6.35-9.50) (9.50-12.7) (12.7-15.8) 31518110BPK100 31518111BPK100 31518112BPK100 31518113BPK100 Red White Blue Brown 31648042GPK100 31605015GPK100 31648043GPK100 31648044GPK100 ½, ¾ .375"-.500" .500"-.625" .625"-.750" .750"-.875" (9.50-12.7) (12.7-15.8) (15.8-19.0) (19.0-22.2) 31518116BPK100 31518117BPK100 31518118BPK100 31518119BPK100 Blue Brown Yellow Orchid 31648045GPK100 31648046GPK100 31648047GPK100 31648048GPK100 .500"-.625" .625"-.750" .750"-.875" .875"-1.00" 1.00"-1.125" (12.7-15.8) (15.8-19.0) (19.0-22.2) (22.2-25.4) (25.4-28.5) 31518123BPK100 31518124BPK100 31518125BPK100 31518126BPK100 31518127BPK100 Brown Yellow Orchid Gray Pink 31648050GPK100 31648051GPK100 31648052GPK100 31648053GPK100 31648054GPK100 Note: Catalog numbers above with “PK100” suffix, i.e. 31518101BPK100, are bulk packed 100 per carton Locknuts and Metal Clad Sealing O-Rings NPT Hub Size Zinc-Plated Steel Locknuts Non-Metallic Locknuts Metal Clad Sealing O-Rings* ³⁄₈ 00322001LPK50 00322002LPK50 31622001LPK50 31622002LPK50 31622003LPK50 31622007LPK50 20509001 20509002 00322003LPK50 00322004LPK50 00322005LPK50 31622008LPK50 20509003 20509004 20509005 20509006 20509007 20509008 Note: Catalog numbers above with “PK50” suffix, i.e. 00322001LPK50, are bulk packed 50 per carton. See page V-96 for technical information and dimensional drawings. *UL listed and CSA certified. Multi-Hole Cord Grip Connectors NPT Hub Size Cord Diameter Color Holes Catalog NumberInches (mm) ½ .205" (5.2mm) Black 2 SEC50B252 ¾ .205" (5.2mm) Black 3 SEC75B352 ¾ .205" (5.2mm) Black 4 SEC75B452 ½ .220" (5.6mm) Black 3 SEC50B356 1 .215" (5.5mm) Black 9* SEC100BSMH9 1¼ .215" (5.5mm) Black 13* SEC125BSMH13 Note: *Skinned bushings, field configurable. SEC100BSMH9

www.hubbell-wiring.com Wiring Device-Kellems Hubbell Juniors are a miniature liquidtight version of the full-sized Hubbell cord connectors. They feature the same GOTCHA ® ring technology and neoprene bushings. They also come with or without a nylon spiral for arc-of- bend control and longer cord life. They are available in ¼", ³⁄₈", and ½" NPT sizes in both gray and black. Kellems® Wire Management Products Hubbell Juniors® Miniature Connectors Features and Benefits Patented GOTCHA® ring incorporates a split hinge design to prevent friction and provide strain relief Lubricated neoprene bushing compresses evenly for a liquidtight seal and added pull-out protection Nylon spiral provides arc-of-bend control for cord protection Threaded hexagon shaped nylon locknut secures tightly and is also corrosion resistant Nylon compression nut has a tapered interior dome to easily drive the bushing into the connector body Nylon connector body is a one piece design with a tapered interior that seals the bushing evenly for a positive seal

www.hubbell-wiring.comV-86 Wiring Device-Kellems Miniature Nylon Cord Connector NPT Hub Size Cord Diameter Range Inches (mm) Gray Black .08"-.14" .14"-.20" .20"-.27" (1.9-3.4) (3.4-5.1) (5.1-6.7) HJ1001GPK25 HJ1002GPK25 HJ1003GPK25 HJ1001BPK25 HJ1002BPK25 HJ1003BPK25 ³⁄₈ .15"-.21" .21"-.28" .28"-.34" (3.7-5.3) (5.3-7.0) ( 7.0 -8.6) HJ1004GPK25 HJ1005GPK25 HJ1006GPK25 HJ1004BPK25 HJ1005BPK25 HJ1006BPK25 .06"-.13" .13"-.19" .19"-.25" .25"-.31" .31"-.38" .38"-.44" (1.6-3.2) (3.2-4.7) (4.7-6.3) (6.3-7.9) ( 7.9 -9.5) (9.5-11.1) HJ1055GPK25 HJ1056GPK25 HJ1057GPK25 HJ1058GPK25 HJ1059GPK25 HJ1060GPK25 HJ1055BPK25 HJ1056BPK25 HJ1057BPK25 HJ1058BPK25 HJ1059BPK25 HJ1060BPK25 Miniature Nylon Cord Connector with Spiral NPT Hub Size Cord Diameter Range Inches (mm) Gray Black .08"-.14" .14"-.20" .20"-.27" (1.9-3.4) (3.4-5.1) (5.1-6.7) HJ1010GPK25 HJ1011GPK25 HJ1012GPK25 HJ1010BPK25 HJ1011BPK25 HJ1012BPK25 ³⁄₈ .15"-.21" .21"-.28" .28"-.34" (3.7-5.3) (5.3-7.0) ( 7.0 -8.6) HJ1013GPK25 HJ1014GPK25 HJ1015GPK25 HJ1013BPK25 HJ1014BPK25 HJ1015BPK25 .13"-.19" .19"-.25" .25"-.31" .31"-.38" .38"-.44" (3.2-4.7) (4.7-6.3) (6.3-7.9) ( 7.9 -9.5) (9.5-11.1) HJ1038GPK25 HJ1039GPK25 HJ1040GPK25 HJ1041GPK25 HJ1042GPK25 HJ1038BPK25 HJ1039BPK25 HJ1040BPK25 HJ1041BPK25 HJ1042BPK25 ¾ .25"-.49" .45"-.71" (6.4-12.3) (11.4-18.0) HJ1043GPK25* HJ1044GPK25* HJ1043BPK25* HJ1044BPK25* Note: *Locknuts sold separately, see page V-84 for additional information. Miniature Nylon Snap-In Cord Connector with Spiral Cord Diameter Range Inches (mm) For Chassis Thickness Gray Black Note: Catalog numbers above with “PK25” suffix, i.e. HJ1001GPK25, are bulk packed 25 per carton. See page V-97 for technical information and dimensional drawings. Kellems® Wire Management Products Hubbell Juniors® Miniature Nylon Cord Connectors Gray Cord Connector Black Cord Connector Gray Cord Connector with Spiral Black Cord Connector with Spiral Gray Snap-In Cord Connector Black Snap-In Cord Connector

V-87www.hubbell-wiring.com Wiring Device-Kellems Operating Temperatures Material Temperature Range Aluminum -40°F to +300°F (-40°C to +149°C) Nylon (connectors and GOTCHA ® rings) -40°F to +225°F (-40°C to +107°C) Plated steel* -60°F to +1000°F (-51°C to +537°C) Stainless steel* -60°F to +1000°F (-51°C to +537°C) Neoprene (bushings) -30°F to +240°F (-34°C to +115°C) Note: *Due to the limiting factors of nylon and neoprene, any complete cord connector with a GOTCHA ring, Form 1-5, will continuously perform in the range of -30°F to Cord connectors without GOTCHA rings, Form 6-8, will continuously operate in the range -30°F to +240°F (-34°C to +115°C) due to the limiting factor of neoprene. Hazardous Locations Hubbell cord connectors are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class Ill Div. 1 & 2 in accordance with the NEC. Flammability Hubbell nylon cord connectors have a UL 94-V2 rating. Approvals Agency UL Listed in accordance with Standard 514B for indoor/outdoor use. CSA Certified. United States Coast Guard Approved, Title 46-Part 111. Form Size Definition The term “Form Size” refers to the physical overall size of a cord connector. Form 1 is the smallest size. Form 8 is the largest size. Knockout Holes Knockout Hole Recommended Knockout Hole Recommended Knockout Hole Recommended NPT Min. to Max. PG Metric Hub Size Inches (mm) Hub Size Inches (mm) Hub Size Inches (mm) NPT, PG and Metric Thread Low Profile Connectors Specifications Material 6/6 Nylon. Gland Buna N. Temperature Range -22°F to 225°F (-30°C to 107°C). Cord Connectors are Halogen and Silicon free. Protection Class IP66 Suitability. Flammability UL 94V-2. Listings/Certifications UL Listing File E-41567, UL Recognition File E-41567. CSA File LR27378C, VDE Marks Licence #136681. Kellems® Wire Management Products Technical Information Cord Connectors SECP29G

www.hubbell-wiring.comV-88 Wiring Device-Kellems A (Overall) B Ref. C D F E Straight Hubbell Connectors Aluminum Inches (mm) Nylon Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E A Dia. B Ref. C D Throat Dia. E A/C* A/F* A/C* A/F* ¼-18 1 .88" (22.4) .90" (22.9) .46" (11.7) .32" (8.1) .99" (25.1) .88" (22.4) 1.00" (25.4) 1.10" (27.9) .43" (10.9) .33" (8.4) .1.00" (25.4) .93" (23.6) ³⁄₈-18 1 .88" (22.4) .90" (22.9) .46" (11.7) .44" (11.2) .99" (25.1) .88" (22.4) 1.00" (25.4) 1.10" (27.9) .43" (10.9) .45" (11.4) .1.00" (25.4) .93" (23.6) ½-14 1 .88" (22.4) .90" (22.9) .46" (11.7) .44" (11.2) 1.00" (25.4) .88" (22.4) 1.00" (25.4) 1.10" (27.9) .46" (11.7) .45" (11.4) .1.00" (25.4) .93" (23.6) ½-14 2 1.13" (28.7) 1.10" (27.9) .55" (14.0) .64" (16.3) 1.11" (28.2) 1.00" (25.4) 1.32" (33.5) 1.50" (38.1) .53" (13.5) .58" (14.7) 1.25" (31.7) 1.12" (28.4) ½-14 3 1.38" (35.1) 1.50" (38.1) .55" (14.0) .64" (16.3) 1.40" (35.6) 1.25" (31.7) ¾-14 2 1.13" (28.7) 1.10" (27.9) .55" (14.0) .64" (16.3) 1.29" (32.8) 1.13" (28.7) ¾-14 3 1.38" (35.1) 1.50" (38.1) .55" (14.0) .82" (20.8) 1.40" (35.6) 1.25" (31.7) 1.56" (39.6) 1.60" (40.6) .55" (14.0) .77" (19.6) 1.44" (36.6) 1.31" (33.3) 1-11½ 4 1.75" (44.4) 1.60" (40.6) .71" (18.0) 1.02" (25.9) 1.81" (46.0) 1.62" (41.1) 1.88" (47.8) 1.75" (44.4) .70" (17.8) 1.01" (25.7) 1.84" (46.7) 1.63" (41.4) 1-11½ 5 2.31" (58.7) 1.70" (43.2) .66" (16.8) 1.01" (25.7) 2.28" (57.9) 2.00" (50.8) 1¼-11½ 5 2.31" (58.7) 1.70" (43.2) .74" (18.8) 1.26" (32.0) 2.28" (57.9) 2.12" (53.8) 1½-11½ 5 2.31" (58.7) 1.70" (43.2) .74" (18.8) 1.38" (35.1) 2.28" (57.9) 2.12" (53.8) 1½-1 1½ 6 3.00" (76.2) 2.20" (55.9) .75" (19.0) 1.50" (38.1) 2.97" (75.4) 2.75" (69.8) 2-11½ 6 3.00" (76.2) 2.20" (55.9) .80" (20.3) 1.92" (48.8) 3.24" (82.4) 3.00" (76.2) 2-11½ 7 3.85" (97.8) 2.70" (68.6) .88" (22.4) 1.94" (49.3) 4.05" (102.9) 3.75" (95.2) 2½-8 7 3.85" (97.8) 2.70" (68.6) 1.30" (33.0) 2.32" (58.9) 4.34" (110.2) 4.02" (102.1) 2½-8 8 4.75" (120.6) 2.70" (68.6) 1.25" (31.7) 2.38" (60.5) 4.86" (123.4) 4.50" (114.3) 3-8 7 3.85" (97.8) 2.70" (68.6) 1.30" (33.0) 2.54" (64.5) 4.34" (110.2) 4.02" (102.1) 3-8 8 4.50" (114.3) 2.70" (68.6) 1.38" (35.1) 3.00" (76.2) 4.86" (123.4) 4.50" (114.3) Note: *A/C— Across Corners; A/F—Across Flats. Kellems® Wire Management Products Technical Information Cord Connectors Dimensions shown are approximate and are subject to change without notice.

V-89www.hubbell-wiring.com Wiring Device-Kellems A (Overall) B Ref. C D F E Straight Hubbell Connectors Zinc-Plated Steel Inches (mm) Stainless Steel Inches (mm) F NPT Inches Form A B Ref. C D Throat Dia. E A B Ref. C D Throat Dia. E (25.7) .88" (22.4) .90" (22.9) .46" (11.7) .38" (9.7) .87" (22.1) .75" (19.0) ³⁄₈-18 1 .98" (24.9) .88" (22.4) .90" (22.9) .42" (10.7) .45" (11.4) .99" (25.1) .88" (22.4) 1.01" (25.7) .88" (22.4) .90" (22.9) .46" (11.7) .45" (11.4) .87" (22.1) .75" (19.0) ½-14 1 .98" (24.9) .88" (22.4) .90" (22.9) .55" (14.0) .45" (11.4) 1.00" (25.4) .88" (22.4) ½-14 2 1.27" (32.3) 1.13" (28.7) 1.20" (30.5) .55" (14.0) .64" (16.3) 1.10" (28.2) 1.00" (25.4) 1.30" (33.0) 1.13" (28.7) 1.10" (27.9) .54" (13.7) .63" (16.0) 1.16" (29.5) 1.00" (25.4) ½-14 3 1.55" (39.4) 1.38" (35.1) 1.50" (38.1) .55" (14.0) .64" (16.3) 1.40" (35.6) 1.25" (31.7) ¾-14 2 1.27" (32.3) 1.13" (28.7) 1.20" (30.5) .55" (14.0) .64" (16.3) 1.29" (32.8) 1.13" (28.7) ¾-14 3 1.55" (39.4) 1.38" (35.1) 1.40" (35.6) .55" (14.0) .82" (20.8) 1.40" (35.6) 1.25" (31.7) 1.59" (40.4) 1.38" (35.1) 1.30" (33.0) .56" (14.2) .81" (20.6) 1.44" (36.6) 1.25" (31.7) 1-11½ 3 1.55" (39.4) 1.38" (35.1) 1.40" (35.6) .70" (17.8) .89" (22.6) 1.54" (39.1) 1.38" (35.1) 1-11½ 4 1.92" (48.8) 1.69" (42.9) 1.60" (40.6) .70" (17.8) 1.02" (25.9) 1.95" (49.5) 1.69" (42.9) 2.02" (51.3) 1.75" (44.4) 1.40" (35.6) .70" (17.8) 1.03" (26.2) 1.88" (47.8) 1.63" (41.4) 1-11½ 5 2.40" (61.0) — 1.70" (43.2) .70" (17.8) 1.02" (25.9) 2.46" (62.5) 2.15" (54.6) 1¼-11½ 5 2.40 " (61.0) — 1.70" (43.2) .73" (18.5) 1.27" (32.3) 2.48" (63.0) 2.19" (55.6) 1½-11½ 5 2.40" (61.0) — 1.70" (43.2) .74" (18.8) 1.39" (35.3) 2.48" (63.0) 2.19" (55.6) 1½-11½ 6 3.06" ( 77.7 ) — 2.20" (55.9) .75" (19.0) 1.52" (38.6) 3.04" ( 77.2) 2.83" (71.9) 2-11½ 6 3.06" ( 77.7 ) — 2.20" (55.9) .78" (19.8) 1.92" (48.8) 3.32" (84.3) 3.07" (78.0) 2-11½ 7 3.95" (100.3) — 2.70" (68.6) .78" (19.8) 1.99" (50.5) 4.18" (106.2) 3.89" (98.8) Note: *A/C— Across Corners; A/F—Across Flats. Kellems® Wire Management Products Technical Information Cord Connectors Dimensions shown are approximate and are subject to change without notice.

www.hubbell-wiring.comV-90 Wiring Device-Kellems Dimensions shown are approximate and are subject to change without notice. B Ref. A Ref. D C E F G B Ref. A D C E F G 45° Hubbell Connectors Aluminum Inches (mm) Zinc Plated Steel Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E G Dia. A Dia. B Ref. C D Throat Dia. E G Across Corners Across Flats Across Corners Across Flats Across Corners Across Flats ½-14 2 2.00" (50.8) 1.90" (48.3) .55" (14.0) .56" (14.2) 1.27" (32.3) 1.10" (27.9) 1.13" (28.6) 1.97" (50.0) 1.90" (48.3) .55" (14.0) .57" (14.4) 1.24" (31.5) 1.06" (26.9) 1.27" (32.3) 1.13" (28.6) ¾-14 3 2.30" (58.4) 2.50" (65.3) .56" (14.2) .75" (19.0) 1.48" (37.6) 1.28" (32.5) 1.38" (34.9) 1-11½ 4 2.60" (66.0) 2.80" (71.1) .70" (17.8) 1.00" (25.4) 1.69" (42.9) 1.50" (38.1) 1.75" (44.4) 1½-11½ 5 3.90" (99.1) 3.90" (9.91) .74" (18.8) 1.25" (31.7) 2.45" (62.2) 2.13" (54.0) 2.31" (58.7) 1½-11½ 5 3.90" (99.1) 3.90" (99.1) .74" (18.8) 1.50" (38.1) 2.45" (62.2) 2.13" (54.0) 2.31" (58.7) 90° Hubbell Connectors Aluminum Inches (mm) Zinc Plated Steel Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E G Dia. A Dia. B Ref. C D Throat Dia. E G Across Corners Across Flats Across Corners Across Flats Across Corners Across Flats ³⁄₈-18 1 1.27" (32.3) 2.00" (50.8) .46" (11.7) .44" (11.2) 1.15" (29.2) 1.10" (27.9) .88" (22.2) ½-14 2 1.56" (39.6) 2.30" (58.4) .50" (12.7) .55" (13.9) 1.30" (33.0) 1.13" (28.7) 1.13" (28.6) 1.65" (41.9) 2.38" (60.5) .55" (14.0) .55" (13.8) 1.29" (32.8) 1.13" (28.7) 1.27" (32.3) 1.13" (28.6) ¾-14 3 1.79" (45.5) 2.80" (71.1) .56" (14.2) .77" (19.4) 1.49" (37.8) 1.31" (33.3) 1.38" (34. 1.88" (47.8) 2.90" (73.7) .56" (14.2) .77" (19.4) 1.52" (38.6) 1.33" (33.8) 1.55" (39.2) 1.38" (34.9) 1-11½ 4 2.08" (52.8) 3.20" (81.3) .70" (17.8) 1.00" (25.4) 1.70" (43.2) 1.50" (38.1) 1.75" (44.4) 2.16" (54.9) 3.20" (81.3) .70" (17.8) 1.00" (25.4) 1.72" (43.7) 1.50" (38.1) 1.92" (48.8) 1.69" (42.8) 1¼-11½ 5 3.18" (80.8) 4.30" (109.2) .73" (18.5) 1.26" (32.0) 2.47" (62.7) 2.15" (54.6) 2.31" (58.7) 1½-11½ 5 3.18" (80.8) 4.30" (109.2) .75" (19.2) 1.50" (38.1) 2.47" (62.7) 2.15" (54.6) 2.31" (58.7) 2-11½ 6 3.51" (89.2) 5.50" (139.7) .80" (20.3) 1.92" (48.8) 2.98" (75.7) 2.78" (70.6) 3.00" (76.2) 90° Hubbell Connectors Nylon Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E G Dia. Across Corners Across Flats ½-14 2 1.41" (35.8) 2.50" (63.5) .55" (14.0) .58" (14.6) 1.23" (31.2) 1.12" (28.2) 1.32" (33.4) ¾-14 3 1.65" (41.9) 2.81" (71.4) .56" (14.2) .77" (19.4) 1.42" (36.1) 1.29" (32.8) 1.56" (39.6) 1-11½ 4 1.99" (50.5) 3.30" (83.8) .70" (17.8) 1.01" (25.7) 1.82" (46.2) 1.60" (40.6) 1.88" (47.6) Kellems® Wire Management Products Technical Information Cord Connectors

V-91www.hubbell-wiring.com Wiring Device-Kellems A (Overall) B Ref. C D F E A (Overall) B Ref. C (N.P.T. Thread Depth) D E A D CF B E SEALING NUT Recommended knockout size Dimensions shown are approximate and are subject to change without notice. Low Profile Non-Metallic NPT, PG and Metric Thread Connectors Nylon Inches (mm) Hub Size A B C D E F Female Hubbell Connectors Aluminum Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E Across Corners Across Flats ³⁄₈-18 1 .88" (22.4) 1.40" (35.6) .56" (14.2) .44" (11.2) .94" (23.9) .81" (20.6) ½-14 2 1.13" (28.7) 1.80" (45.7) .56" (14.2) .63" (16.0) 1.15" (29.2) 1.00" (25.4) ¾-14 2 1.13" (28.7) 2.10" (53.3) .75" (19.0) .63" (16.0) 1.44" (36.6) 1.25" (31.7) 1-11½ 4 1.75" (44.5) 2.30" (58.4) .88" (22.4) 1.10" (27.9) 1.88" (47.8) 1.63" (41.4) 1¼-11½ 5 2.31" (58.7) 2.80" (71.1) .95" (24.1) 1.43" (36.3) 2.64" (67.1) 2.29" (58.2) 1½-11½ 5 2.31" (58.7) 2.80" (71.1) .95" (24.1) 1.43" (36.3) 2.64" (67.1) 2.29" (58.2) Underground Feeder Connectors Aluminum Inches (mm) Zinc-Plated Steel Inches (mm) Nylon Inches (mm) F NPT Inches Form A Dia. B Ref. C D Throat Dia. E A B Ref. C D Throat Dia. E A Dia. B Ref. C D Throat Dia. E ½-14 2 1.13" (28.7) 1.10" (27.9) .55" (14.0) .64" (16.3) 1.10" (27.9) 1.00" (25.4) 1.27" (32.3) 1.13" (28.7) 1.20" (30.5) .55" (14.0) .64" (16.3) 1.11" (28.2) 1.00" (25.4) 1.32" (33.5) 1.50" (38.1) .55" (14.0) .58" (14.7) 1.25" (31.7) 1.13" (28.7) ¾-14 2 1.13" (28.7) 1.10" (27.9) .55" (14.0) .64" (16.3) 1.29" (32.8) 1.13" (25.4) 1.27" (32.3) 1.13" (28.7) 1.20" (30.5) .55" (14.0) .64" (16.3) 1.29" (32.8) 1.13" (28.7) ¾-14 3 1.13" (28.7) 1.50" (38.1) .55" (14.0) .82" (20.8) 1.40" (35.6) 1.25" (31.7) 1.55" (39.4) 1.38" (35.1) 1.40" (35.6) .56" (14.2) .82" (20.8) 1.40" (35.6) 1.25" (31.7) 1.56" (39.6) 1.60" (40.6) .56" (14.2) .77" (19.6) 1.44" (36.6) 1.31" (33.3) Note: *A/C - Across Corners; A/F - Across Flats. Kellems® Wire Management Products Technical Information Cord Connectors

www.hubbell-wiring.comV-92 Wiring Device-Kellems

2 Conductors

Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Dia. Inches (mm) .25" (6.2) .31" ( 7.8) .33" (8.4) .37" (9.3) .38" (9.7) .40" (10.2) .54" (13.7) .62" (15.6) .68" (17.1) .81" (20.6) Color Black Black White White Blue Blue Brown Brown Yellow Orchid NPT Form Catalog Number* ¼ 1 HC1004 HC1004 HC1005 HC1005 HC1006 HC1006 — — — — ³⁄₈ 1 HC1010 HC1010 HC1011 HC1011 HC1012 HC1012 — — — — ½ 1 HC1016 HC1016 HC1017 HC1017 HC1018 HC1018 — — — — ½ 2 HC1022 HC1022 HC1022 HC1022 HC1023 HC1023 HC1024 HC1024 — — ½ 3 — — — — HC1025 HC1025 HC1026 HC1026 HC1027 HC1028 ¾ 2 HC1032 HC1032 HC1032 HC1032 HC1033 HC1033 HC1034 HC1034 — — ¾ 3 — — — — HC1035 HC1035 HC1036 HC1036 HC1037 HC1038 1 4 — — — — HC1039 HC1039 HC1040 HC1040 HC1041 HC1042 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded.

3 Conductors

Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Dia. Inches (mm) .26" (6.5) .33" (8.3) .35" (8.9) .39" (9.8) .39" (9.9) .42" (10.7) .57" (14.4) .65" (16.4) .71" (18.0) .85" (21.5) Color Black White White Blue Blue Blue Brown Yellow Yellow Orchid NPT Form Catalog Number* ¼ 1 HC1004 HC1005 HC1005 HC1006 HC1006 HC1006 — — — — ³⁄₈ 1 HC1010 HC1011 HC1011 HC1012 HC1012 HC1012 — — — — ½ 1 HC1016 HC1017 HC1017 HC1018 HC1018 HC1018 — — — — ½ 2 HC1022 HC1022 HC1022 HC1023 HC1023 HC1023 HC1024 — — — ½ 3 — — — HC1025 HC1025 HC1025 HC1026 HC1027 HC1027 HC1028 ¾ 2 HC1032 HC1032 HC1032 HC1033 HC1033 HC1033 HC1034 — — — ¾ 3 — — — HC1035 HC1035 HC10 35 HC1036 HC1037 HC1037 HC1038 1 4 — — — HC1039 HC1039 HC1039 HC1040 HC1041 HC1041 HC1042 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded. Kellems® Wire Management Products Technical Information Cord Connectors

V-93www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products Technical Information Cord Connectors Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Diameter Inches (mm) .94" (23.8) 1.08" (27.4) 1.17" (29.7) 1.27" (33.3) 1.44" (36.6) 1.52" (38.6) 1.65" (41.9) 1.77" (45.0) 1.92" (48.8) 2.16" (51.9) NPT Form Catalog Number* 1 5 HC1046 HC1047 HC1048 HC1049 — — — — — — 1¼ 5 HC1051 HC1052 HC1053 HC1054 — — — — — — 1½ 5 HC1056 HC1057 HC1058 HC1059 — — — — — — 1½ 6 — — — HC1060 HC1061 HC1062 HC1063 HC1064 — — 2 6 — — — HC1065 HC1066 HC1067 HC1068 HC1069 — — 2 7 — — — — — — — HC1070 HC1071 HC1073 2½ 7 — — — — — — — HC1076 HC1077 HC1079 3 7 — — — — — — — HC1086 HC1087 HC1089 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded. CordType SVO, SV, SVT SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Diameter Inches (mm) 1.00" (25.4) 1.17" (29.7) 1.24" (31.5) 1.34" (34.0) 1.51" (38.4) 1.65" (41.9) 1.75" (44.5) 1.80" (48.0) 2.07" (52.6) 2.39" (60.7) NPT Form Catalog Number* 1 5 HC1047 HC1048 HC1048 HC1049 — — — — — — 1¼ 5 HC1052 HC1053 HC1053 HC1054 — — — — — — 1½ 5 HC1057 HC1058 HC1058 HC1059 — — — — — — 1½ 6 — — — HC1060 HC1062 HC1063 HC1064 — — — 2 6 — — — HC1065 HC1067 HC1068 HC1069 — — — 2 7 — — — — — — HC1070 HC1071 HC1073 HC1075 2½ 7 — — — — — — HC1076 HC1077 HC1079 HC1081 3 7 — — — — — — HC1086 HC1087 HC1089 HC1091 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded.

www.hubbell-wiring.comV-94 Wiring Device-Kellems

4 Conductors

Cord Type SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Diameter Inches (mm) .36" (9.0) .39" (9.8) .43" (10.8) .42" (10.7) .45" (11.4) .61" (15.5) .70" (17.8) .77" (19.4) .97" (24.6) Color White Blue Blue Blue Blue Brown Yellow Orchid Gray‡ NPT Form Catalog Number* ¼ 1 HC1005 HC1006 HC1006 HC1006 — — — — — ³⁄₈ 1 HC1011 HC1012 HC1012 HC1012 — — — — — ½ 1 HC1017 HC1018 HC1018 HC1018 — — — — — ½ 2 HC1022 HC1023 HC1023 HC1023 HC1023 HC1024 — — — ½ 3 — HC1025 HC1025 HC1025 HC1025 HC1026 HC1027 HC1028 — ¾ 2 — HC1033 HC1033 HC1033 HC1033 HC1034 — — — ¾ 3 — HC1035 HC1035 HC1035 HC1035 HC1036 HC1037 HC1038 — 1 4 — HC1039 HC1039 HC1039 HC1039 HC1040 HC1041 HC1042 HC1043 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded.

5 Conductors

Cord Type S, SO, ST, STO Cord Size #18 #16 #14 #12 #10 #8 #6 Approx. Dia. Inches (mm) Color Blue Brown Yellow Orchid‡ Orchid‡ Pink‡ ‡ NPT Form Catalog Number* ½ 2 HC1023 HC1024 — — — — — ½ 3 HC1025 HC1026 HC1027 HC1028 HC1028 — — ¾ 2 HC1033 HC1034 — — — — — ¾ 3 HC1035 HC1036 HC1037 HC1038 HC1038 — — 1 4 HC1039 HC1040 HC1041 HC1042 HC1042 HC1044 — 1 5 — — — HC1045 HC1045 HC1047 HC1048 1¼ 5 — — — HC1050 HC1050 HC1052 HC1053 1½ 5 — — — HC1055 HC1055 HC1057 HC1058 Note: *Must add prefix, see Note 1; suffix, see Note 2, on page V-95. ‡F5 and larger will not be color coded. Kellems® Wire Management Products Technical Information Cord Connectors

V-95www.hubbell-wiring.com Wiring Device-Kellems Note: 1. Add the proper prefix to the HC number to identify the type of connector desired: SHC = Straight Hubbell Connector NHC = 90° Hubbell Connector FHC = Female Hubbell Connector VHC = 45° Hubbell Connector 2. Add the proper suffix to identify material desired: Aluminum = No suffix Zinc-Plated Steel = ZP Corrosion Resistant Nylon = CR Stainless Steel = SS 3. This chart is a general guide to assist in the selection of Hubbell Cord Connectors for various cord sizes. The Hubbell Cord Connector catalog numbers selected, have been inserted into spaces which in our judgment represent the best cord connector which will fit the listed cord size. The diameters of the cords are approximate and may vary depending on the manufacturer. It is suggested that the appropriate cord manufacturer’s dimension chart be consulted for exact dimensions. 4. Cable jacket may have to be stripped to allow conductors to pass through connector body. Kellems® Wire Management Products Technical Information Cord Connectors Cord Type SJ, SJO, SJT, SJTO S, SO, ST, STO Approx. Diameter Inches (mm) .94" (23.8) 1.08" (27.4) 1.17" (29.7) 1.27" (33.3) 1.44" (36.6) 1.52" (38.6) 1.65" (41.9) 1.77" (45.0) 1.92" (48.8) NPT Form Catalog Number* 1 5 HC1047 HC1049 HC1049 — — — — — — 1¼ 5 HC1052 HC1054 HC1054 — — — — — — 1½ 5 HC1057 HC1059 HC1059 — — — — — — 1½ 6 — HC1060 HC1060 HC1061 HC1063 HC1064 — — — 2 6 — HC1064 HC1065 HC1066 HC1068 HC1069 — — — 2 7 — — — — — HC1070 HC1071 HC1073 HC1074 2½ 7 — — — — — HC1076 HC1077 HC1079 HC1080 3 7 — — — — — HC1086 HC1087 HC1089 HC1090 Note: *Must add prefix, see Note 1; suffix, see Note 2, below. ‡F5 and larger will not be color coded.

www.hubbell-wiring.comV-96 Wiring Device-Kellems A Thread Size (N.P.S.) C Minimum Thk. B Maximum Diameter A C B A C B NPT Thread Locknuts Zinc-Plated Steel NPT Hub Size A Inside Diameter B Outside Dia. C Thickness Steel Catalog NumberInches Inches (mm) Inches (mm) 1¼ 1¼"-11½ 2.28" (57.9) .13" (3.3) 00322004LPK50 1½ 1½"-11½ 2.60" (66.0) .13" (3.3) 00322005LPK50 Metal Clad Sealing O-Rings – Sizes ½ - 4 Zinc-Plated Steel with Neoprene Ring NPT Hub Size A Inside Diameter B Outside Dia. C Thickness Catalog NumberInches (mm) Inches (mm) Inches (mm) Chrome Plated Steel with Neoprene Ring Nylon PG Thread Locknuts PG Thread Size A Inches (mm) B Inches (mm) C Inches (mm) Catalog Number Nylon Metric Thread Locknuts PG Thread Size A Inches (mm) B Inches (mm) C Inches (mm) Catalog Number Kellems® Wire Management Products Technical Information Locknuts and Sealing O-Rings Dimensions shown are approximate and are subject to change without notice.

V-97www.hubbell-wiring.com Wiring Device-Kellems Hubbell Juniors® Material Operating Temperature Range Nylon (connectors and GOTCHA ® rings) -40°F to +225°F (-40°C to +107°C) Neoprene (bushings) -30°F to +240°F (-34°C to +115°C) Due to the limiting factors of nylon and neoprene, any complete liquidtight Hubbell Junior will continuously perform in the range of -30°F to +225°F (-34°C to +107°C). Snap-In continuously performs -40°F to +225°F (-40°C to +107°C). Flammability Hubbell Juniors have a UL 94V-2 rating. Certifications Product Agency Liquidtight and Liquidtight with Spiral UL Listed. CSA Certified. Snap-In UL Recognized. CSA Certified. Knockout Holes Knockout Hole Recommended NPT Min. to Max. Hub Size inches (mm) Kellems® Wire Management Products Technical Information Hubbell Juniors® Miniature Nylon Cord Connectors Dimensions shown are approximate and are subject to change without notice. B E F C DA B F G DE A C G D F C B A Chassis Thickness Max E Snap-In Diameter Range Inches (mm) For Chassis Thickness (Max.) Inches (mm) Required Hole Size A Inches (mm) B Inches (mm) Dimensional Specifications E Inches (mm) F Inches (mm) G Inches (mm) C Inches (mm) D Inches (mm) .22"-.27" (5.6-6.9) .10" (2.5) .50" (12.7) .45" (11.4) .28" (7.1) .28" (7.1) .54" (13.7) .12" (3.0) 1.84" (44.2) .28"-.32" (7.1-8.1) .10" (2.5) .50" (12.7) .47" (11.9) .28" (7.1) .33" (8.4) .59" (15.0) .12" (3.0) 1.84" (44.2) .30"-.36" (7.6-9.1) .13" (3.3) .63" (16.0) .55" (14.0) .36" (9.1) .37" (9.4) .65" (16.5) .14" (3.6) 2.18" (55.4) .32"-.43" (8.1-10.9) .13" (3.3) .75" (19.0) .66" (16.8) .45" (11.4) .44" (11.2) .75" (19.1) .14" (3.6) 2.60" (66.0) Liquidtight F NPT Inches A Dia. Inches (mm) B Ref. Inches (mm) C Inches (mm) D Throat Dia. Inches (mm) E Across Corners Inches (mm) Across Flats Inches (mm) ¼-18 .65" (16.5) 1.30" (33.0) .40" (10.2) .29" (7.4) .65" (16.5) .60" (15.2) ³⁄₈-18 .81" (20.6) 1.44" (36.6) .41" (10.4) .36" (9.1) .81" (20.6) .75" (19.1) ½-14 1.00" (25.4) 1.56" (39.6) .46" (11.7) .45" (11.4) .99" (25.1) .92" (23.4) Liquidtight with Spiral G NPT Inches A Dia. Inches (mm) B Ref. Inches (mm) C Inches (mm) D Throat Dia. Inches (mm) E Inches (mm) F Across Corners Inches (mm) Across Flats Inches (mm) ¼-18 .65" (16.5) 2.55" (64.8) .40" (10.2) .29" (7.4) .27" (6.9) .65" (16.5) .60" (15.2) ³⁄₈-18 .81" (20.6) 3.10" (78.7) .41" (10.4) .36" (9.1) .35" (8.9) .81" (20.6) .75" (19.1) ½-14 1.00" (25.4) 3.72" (94.5) .46" (11.7) .45" (11.4) .45" (11.4) .99" (25.1) .92" (23.4)

www.hubbell-wiring.comV-98 Wiring Device-Kellems Kellems® Wire Management Products PolyTuff® I and PolyTuff® II Non-Metallic Liquidtight Conduit Features and Benefits Rigid PVC core bonded to flexible PVC jacket All non-metallic construction ends metal fatigue and separation problems Cuts cleanly with a knife or PVC cutter so there are no jagged metal edges UL Listed and CSA Certified PolyTuff® I Conduit, Gray PVC core with corrugated walls bonded to PVC jacket Handles twists, turns, bends, switchbacks and straightaways with ease All non-metallic construction ends fatigue and separation problems Can be cut with a knife or PVC cutters UL Recognized and CSA Certified PolyTuff® II Tubing Trade Size (metric designator) Feet (m) Catalog Number ¼ (10) 100 (30.5) B2025 ³⁄₈ (12) 100 (30.5) B2038 ½ (16) 100 (30.5) B2050 ¾ (21) 100 (30.5) B2075 1 (27) 100 (30.5) B2100 1¼ (35) 100 (30.5) B2125 1½ (41) 50 (15.2) B2150 2 (53) 50 (15.2) B2200 Note: See page V-100 for approved fittings. See pages V-102 and V-103 for technical information and dimensional drawings. IP66 SUITABILITY PolyTuff® I Conduit Trade Size (metric designator) Feet (m) Catalog Number ³⁄₈ (12) 100 (30.5) G1038 ½ (16) 100 (30.5) G1050 ¾ (21) 100 (30.5) G1075 1 (27) 100 (30.5) G1100 1¼ (35) 100 (30.5) G1125 1½ (41) 50 (15.2) G1150 2 (53) 50 (15.2) G1200 Note: See pages V-66 and V-67, V-100 and V-101 for approved fittings. See pages V-102 and V-103 for technical information and dimensional drawings. IP66 SUITABILITY PolyTuff® II Tubing, Black

V-99www.hubbell-wiring.com Wiring Device-Kellems Kellems® Wire Management Products PolyTuff® Non-Metallic and Metallic Liquidtight Conduit Fittings Features and Benefits Non-integral ferrule provides conduit seal and superior pullout protection Nylon compression nut has a tapered dome to tighten ferrule onto conduit Neoprene O-ring provides liquidtight seal at hub or enclosure Nylon locknut fastens connector securely to enclosure and provides superior corrosion resistance Nylon two-piece swivel body enables fitting to twist from 0° to 90° Hexagonal, screw-machined steel thru 1", and malleable iron on larger sizes. Nut compresses gland-ring onto conduit Non-integral, reusable steel, ferrule is easily installed, to seal conduit Tapered, machined threads fasten securely and provide additional liquidtight sealing Split, nylon, gland-ring compresses conduit onto ferrule Threaded one-piece steel body Locknut has hardened steel tangs to grip securely Nylon gasket provides liquidtight seal at hub Optional insulated and non-insulated throat

www.hubbell-wiring.comV-100 Wiring Device-Kellems PS05GYKIT P1259NGY P125NGY P075NGYA PS0509NGY SwivelLok® Multi-Position Straight with Male Non-Metallic Liquidtight Fittings Trade Size (metric designator) Black Catalog Number Gray Catalog Number ¼ (10) ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) F2025 P038NBKA P050NBKA P075NBKA P100NBKA P038NGYA P050NGYA P075NGYA P100NGYA 1¼ (35) 1½ (41) 2 (53) P125NBK P150NBK P200NBK P125NGY P150NGY P200NGY Note: Fittings are to be used with PolyTuff I and PolyTuff II. See pages V-104 and V-105 for technical information and dimensional drawings. ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads. SwivelLok® Multi-Position with Male Non-Metallic Liquidtight Fittings Trade Size (metric designator) Black Catalog Number Gray Catalog Number ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) PS0389NBK PS0509NBK PS0759NBK PS1009NBK PS0389NGY PS0509NGY PS0759NGY PS1009NGY Note: Fittings are to be used with PolyTuff I and PolyTuff II. See pages V-104 and V-105 for technical information and dimensional drawings. ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads. Fixed 90°Fittings for Non-Metallic Conduit Trade Size (metric designator) Black Catalog Number Gray Catalog Number ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) 1¼ (35) P0389NBK P0509NBK P0759NBK P1009NBK P1259NBK P0389NGY P0509NGY P0759NGY P1009NGY P1259NGY Note: Fittings are to be used with PolyTuff I and PolyTuff II. See pages V-104 and V-105 for technical information and dimensional drawings. ³⁄₈⁄⁄" Liquidtight conduit fitting have ½ NPT male threads. SwivelLok® Flexible Conduit Kit Trade Size (metric designator) Fitting and Conduit Catalog Number ½ (16) ¾ (21)

2 PS0509NGY, 6' G1050

2 PS0759NGY, 6' G1075

Note: See pages V-104 and V-105 for technical information and dimensional drawings. Kellems® Wire Management Products PolyTuff® Non-Metallic Liquidtight Fittings UL Listed to Type 4, 4X, 12 and 13

V-101www.hubbell-wiring.com Wiring Device-Kellems H050 Straight with Male Hubbell Conduit Fitting H0504 45° Angle with Male Hubbell Conduit Fitting H0509 90° Angle with Male Hubbell Conduit Fitting Straight Conduit Fitting Trade Size (metric designator) Insulated Non-Insulated ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) H0381 H0501 H0751 H1001 H038 H050 H075 H100 1¼ (35) 1½ (41) 2 (53) 2½ (63) H1251 H1501 H2001 H2501 H125 H150 H200 H250 3 (78) 3½ (91) 4 (103) H3001 H3501 H4001 H300 H350 H400 Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page V-106 for technical information. 45° Conduit Fitting Trade Size (metric designator) Insulated Non-Insulated ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) H03841 H05041 H07541 H10041 H0384 H0504 H0754 H1004 1¼ (35) 1½ (41) 2 (53) H12541 H15041 H20041 H1254 H1504 H2004 Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page V-106 for technical information. 90° Conduit Fitting Trade Size (metric designator) Insulated Non-Insulated ³⁄₈ (12) ½ (16) ¾ (21) 1 (27) H03891 H05091 H07591 H10091 H0389 H0509 H0759 H1009 1¼ (35) 1½ (41) 2 (53) 2½ (63) 3 (78) 4 (103) H12591 H15091 H20091 H25091 H30091 H40091 H1259 H1509 H2009 H2509 H3009 H4009 Note: ³⁄₈" Liquidtight conduit fitting have ½ NPT male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page V-106 for technical information. Kellems® Wire Management Products Metallic Liquidtight Conduit Fittings

www.hubbell-wiring.comV-102 Wiring Device-Kellems PolyTuff® I Conduit Operating Temperature Range Wet environment 0°F to +140°F (-18°C to +60°C). Oil environment 0°F to +158°F (-18°C to +70°C). Dry environment 0°F to +176°F (-18°C to +80°C). Certifications UL Listed UL Standard 1660. Sunlight resistant approved for outdoor use, direct burial. CSA Certified Meets requirements of NEC. Voltage Rating Maximum 600V. Material Conduit Co-extruded rigid and flexible PVC. PolyTuff® II Tubing Operating Temperature Range Operating environment 0°F to +140°F (-18°C to +60°C). Certifications UL Recognized CSA Certified Voltage Rating Maximum Same as wire insulation rating. Material Tubing Co-extruded rigid and flexible PVC. PolyTuff® I Conduit Trade Size (metric Conduit ID/OD Bend Radius designator) Inches (mm) Inches (mm) PolyTuff® II Tubing Trade Size (metric Conduit ID/OD Bend Radius designator) Inches (mm) Inches (mm) Kellems® Wire Management Products Technical Information Non-Metallic Liquidtight Conduit and Tubing

V-103www.hubbell-wiring.com Wiring Device-Kellems Acetate Solvents D D Acetic Acid B C Acetic Acid (Glacial) C D Acetone D D Acrylontrile A B Alcohols (Aliphatic) C C Aluminum Chloride A A Aluminum Sulfate (Alums) A A Ammonia (Anhydrous Liquids) D D Ammonia (Aqueous) A A Ammoniated Latex A C Ammonium Chloride A A Ammonium Hydroxide A A Amyl Acetate D D Aniline Oils D D Aromatic Hydrocarbons D D Asphalt D D ASTM Fuel A C C ASTM Fuel B D D ASTM #1 Oil B C ASTM #3 Oil C D Barium Chloride A A Barium Sulfide A A Barium Hydroxide A A Benzene (Benzol) D D Benzine (Petroleum Ether) C C Black Liquor A A Bordeaux Mixture A A Boric Acid A A Butyl Acetate D D Butyl Alcohol B C Calcium Hydroxide A A Calcium Hypochlorite A A Carbolic Acid (Phenol) B C Carbon Dioxide A A Carbon Disulfide D D Carbon Tetrachloride D D Carbonic Acid A A Casein A C Caustic Soda A B Chlorine Gas (wet) D D Chlorine Gas (dry) D D Chlorine (water solution) C D Chlorobenzene D D Chlorinated Hydrocarbons D D Chromic Acid B C Citric Acid A A Coal Tar D D Coconut Oil C D Corn Oil A B Cottonseed Oil C D Creosote D D Cresol C D Crysylic Acid D D Cyclohexane B C DDT Weed Killer A C Dibutyl Phthalate D D Diesel Oils C D Diethylene Glycol B C Diethyl Ether A C Di-isodecyl Phthalate D D Dioctyl Phthalate D D Dow General Weed Killer (Phenol) D D Dow General Weed Killer (H2O) B C Ethyl Alcohol C C Ethylene Dichloride D D Ethylene Glycol B C Ferric Chloride A A Ferric Sulfate A A Ferrous Chloride A A Ferrous Sulfate A A Formaldehyde D D Fuel Oil B C Furfural C C Gallic Acid A A Gasoline (Hi Test) C D Glycerine A A Grease A C Green Sulfate Liquor A A Heptachlor in Petroleum Solvents A C Heptane C D Hexane C D Hydrobromic Acid A A Hydrochloric Acid 10% A A Hydrochloric Acid 40% C C Hydrofluoric Acid 70% D D Hydrofluorosilicic Acid A A Hydrofluorosilicic Acid 10% A A Hydrogen Peroxide A B Iso-Octane C C Isopropyl Acetate D D Isopropyl Acid B C Jet Fuels (JP-3, and 5) C D Kerosene C C Ketones D D Linseed Oil A A Lubricating Oils A A Magnesium Chloride A A Magnesium Hydroxide A A Magnesium Sulfate A A Malathion 50 in Aromatics D D Malic Acid A A Methyl Acetate D D Methyl Alcohol C C Methyl Bromide D D Methyl Ethyl Ketone D D Methylene Chloride D D Mineral Oil Monochlorobenezene A A Muriatic Acid (see Hydrochloric Acid) Naphtha C D Naphthalene D D Nitric Acid 10% A B Nitric Acid 35% A C Nitric Acid 70% D D Oleic Acid A C Oleum D D Oxalic Acid A A Pentachlorophenol in Oil B C Pentane C D Perchloroethylene B C Petroleum Ether C C Phenol A A Phosphoric Acid 10% A A Pitch 50% A B Potassium Hydroxide C D Sodium Cyanide A A Stoddard Solvent D D Styrene D D Sulfur Dioxide (liquid) D D Sulfuric Acid 50% A B Sulfuric Acid 98% D D Sulfurous Acid B C Tall Oil D D Tannic Acid A A Toluene D D Trichlorethylene D D Triethanol Amine C D Tricresyl Phosphate (Skydrol) D D Turpentine C D Vinegar A B Vinyl Chloride D D Water A A White Liquor A A Xylene D D Zinc Chloride A A Zinc Sulfate A A Kellems® Wire Management Products Technical Information Non-Metallic Liquidtight Conduit and Tubing PolyTuff® I and II Conduit/Tubing; PVC Chemical Resistance Temp. Temp. Temp. Chemical Conc.* 70°F 150°F Chemical Conc.* 70°F 150°F Chemical Conc.* 70°F 150°F 21°C 66°C 21°C 66°C 21°C 66°C Note: *Conc. = Concentration. (All ratings apply to concentrated or saturated solutions unless otherwise specified.) Chemical resistance ratings are based upon information supplied by the raw material manufacturers. Use as a general guide only – samples should be tested by user under actual conditions. A-Excellent service No harmful effect to reduce service life. Suitable for continuous service. B-Good service life. Moderate to minor effect. Good for intermittent service. Generally suitable for continuous service. C-Fair or limited service. Depends on operating conditions. Generally suitable for intermittent service. Not recommended for continuous service. D-Unsatisfactory service. Not recommended. Rating Code

www.hubbell-wiring.comV-104 Wiring Device-Kellems Kellems® Wire Management Products Technical Information Non-Metallic Liquidtight Fittings PolyTuff® Fittings Operating Temperature* Nylon (Body, Nut, Gripping Ring and Locknut) –40°F to +225°F (–40°C to +107°C). Neoprene (Sealing Ring) –30°F to +240°F (–34°C to +116°C). Flammability Fire Gas Toxicity Product Testing Nylon PolyTuff Fittings have a UL 94V-2 rating. Certifications UL Listed UL50 Type 4X, 12 and 13. CSA Certified PolyTuff I Fittings, PolyTuff II Fittings. Liquidtight Fittings Operating Temperature** Steel/Malleable Iron (Nut, Body, Ferrule) –60°F to +1000°F (–51°C to +538°C). Nylon (Gland Ring) –40°F to +225°F (–40°C to +107°C). Hazardous Locations - NEC Reference Class I, Div. 2 - 501-10(A)(3)B Class II, Div. 1 - 502-10(A)(2) Class II, Div. 2 - 502-10(A)(3) Class III, Div. 1 - 503-10(A)(2) Class III, Div. 2 - 503-10(B) Certifications UL Listed to UL 514B CSA Certified Note: *Due to the limiting factors of nylon and neoprene, PolyTuff Fittings will continuously perform in the range –30°F to +225°F (–34°C to +107°C). **Due to the limiting factors of nylon, metallic liquidtight flexible conduit fittings will continuously perform in the range of –40°F to +225°F (–40°C to +107°C).

V-105www.hubbell-wiring.com Wiring Device-Kellems 45° Position D A G 90° Position F E B C Straight Position A Dia. B D C E A C E B D A Dia. C E B D Straight with Male Non-Metallic Liquidtight Fittings Trade Size (md) A B C D Throat Dia. E Across Corners Across Flats (10) .93" (23.6) 1.45" (36.8) .39" (9.9) .32" (8.1) .86" (Dia.) (21.8) ³⁄₈ (12) 1.14" (29.0) 1.63" (41.4) .57" (14.5) .42" (10.7) 1.41" (35.8) 1.30" (33.0) (16) 1.30" (33.0) 2.14" (54.4) .57" (14.5) .55" (14.0) 1.41" (35.8) 1.30" (33.0) (21) 1.53" (38.9) 2.22" (56.4) .58" (14.7) .74" (18.8) 1.85" (47.0) 1.53" (38.9) (27) 1.80" (45.7) 2.32" (58.9) .72" (18.3) .96" (24.4) 1.94" (49.3) 1.80" (45.7) (35) 2.20" (55.9) 2.15" (54.6) .74" (18.8) 1.30" (33.0) 2.38" (60.5) 2.18" (55.4) (41) 2.49" (63.2) 2.35" (59.7) .76" (19.3) 1.46" (37.1) 2.63" (66.8) 2.43" (61.7) (53) 3.05" ( 77.4) 2.51" (63.6) .79" (20.1) 1.90" (48.3) 3.13" (79.5) 2.93" (74.4) 90° with Male Non-Metallic Liquidtight Fittings Trade Size (md) A B C D Throat Dia. E Across Corners Across Flats (10) .93" (23.6) 1.88" (47.8) .39" (9.9) .32" (8.1) .86"(Dia.) (21.8) (35) 2.21" (56.1) 3.57" (90.7) .74" (18.9) 1.30" (33.0) 2.38" (60.5) 2.18" (55.4) SwivelLok® Multi-Position Liquidtight Fittings Trade Size (md**) A B C D E F G Across Corners Across Flats ³⁄₈ (12) 1.30" (33.0) 3.27" (83.1) .57" (14.5) .55" (14.0) 1.43" (36.3) 2.00" (50.8) 1.41" (35.8) 1.30" (33.0) (16) 1.30" (33.0) 3.27" (83.1) .57" (14.5) .55" (14.0) 1.43" (36.3) 2.00" (50.8) 1.41" (35.8) 1.30" (33.0) (21) 1.53" (38.9) 3.66" (93.0) .58" (15.7) .74" (18.8) 1.59" (40.4) 2.23" (56.6) 1.65" (41.9) 1.53" (38.9) (27) 1.80" (45.7) 4.00" (101.6) .72" (18.3) .96" (24.4) 1.84" (46.7) 2.30" (58.4) 1.94" (49.3) 1.80" (45.7) Note: *A/C = Across Corners, A/F = Across Flats. **md = metric designator. Kellems® Wire Management Products Technical Information Non-Metallic Liquidtight Fittings

www.hubbell-wiring.comV-106 Wiring Device-Kellems A E Throat Dia. B D C F D Throa t Dia. E C A B Ref. B E Throat Dia. D C A F Straight with Male Metallic Metal Fitting Trade Size (md**) A Ref. B C D Throat Dia. E A/C* A/F* A/C* A/F* ³⁄₈ (12) 1.43" (36.3) .59" (15.0) 1.20" (30.0) 1.06" (26.9) .61" (15.5) 1.07" (27.2) .93" (23.6) (16) 1.43" (36.3) .59" (15.0) 1.34" (34.0) 1.19" (30.2) .61" (15.5) 1.22" (31.0) 1.06" (26.9) (21) 1.56" (39.6) .59" (15.0) 1.55" (39.0) 1.37" (34.8) .84" (21.3) 1.43" (36.3) 1.25" (31.8) (27) 1.68" (42.7) .66" (16.8) 1.95" (50.0) 1.69" (42.9) 1.06" (26.9) 1.73" (43.9) 1.56" (39.6) (35) 2.03" (51.6) .63" (16.8) 2.39" (61.0) 2.06" (52.3) 1.37" (34.8) 2.36" (59.9) 2.08" (52.8) (41) 2.21" (56.1) .63" (16.8) 2.72" (69.0) 2.38" (60.5) 1.53" (38.9) 2.79" (70.9) 2.48" (63.0) (53) 2.28" (57.9) .69" (17.5) 3.08" (78.0) 2.87" (72.9) 2.06" (52.3) 3.32" (84.3) 2.90" (73.7) (63) 3.56" (90.4) 1.06" (26.9) 3.92" (100.0) 3.62" (91.9) 2.42" (61.5) 3.85" (97.8) 3.60" (91.4) (78) 3.81" (96.8) 1.06" (26.9) 4.70" (119.0) 4.31" (109.5) 3.01" (76.5) 4.65" (118.1) 4.33" (110.0) (91) 3.81" (96.8) 1.06" (26.9) 5.29" (134.0) 4.81" (122.2) 3.49" (88.6) 5.18" (131.6) 4.82" (122.4) (103) 3.81" (96.8) 1.06" (26.9) 5.75" (146.0) 5.31" (134.9) 3.96" (100.6) 5.75" (146.1) 5.39" (136.9) 45° with Male Metallic Metal Fitting Trade Size (md**) A B C D E Throat Dia. F A/C* A/F* A/C* A/F* ³⁄₈ (12) 1.19" (30.2) 1.28" (32.5) .59" (15.0) 1.20" (30.5) 1.06" (26.9) .60" (15.2) 1.16" (29.5) 1.02" (25.9) (16) 1.19" (30.2) 1.28" (32.5) .59" (15.0) 1.34" (34.0) 1.19" (30.2) .61" (15.2) 1.21" (30.7) 1.06" (26.9) (21) 1.19" (30.2) 1.43" (36.3) .59" (15.0) 1.55" (39.4) 1.45" (36.8) .84" (21.3) 1.50" (38.1) 1.32" (33.5) (27) 1.38" (35.1) 1.53" (38.9) .66" (16.8) 1.95" (49.5) 1.69" (42.9) 1.05" (26.7) 1.82" (46.2) 1.59" (40.4) (35) 1.42" (36.1) 1.69" (42.9) .63" (16.0) 2.39" (60.7) 2.06" (52.3) 1.37" (34.8) 2.32" (58.9) 2.03" (5.16) (41) 1.66" (42.2) 2.00" (50.8) .66" (16.8) 2.72" (69.1) 2.38" (60.5) 1.60" (40.6) 2.62" (66.5) 2.29" (58.2) (53) 1.69" (42.9) 2.25" (57.2) .66" (16.8) 3.08" (78.2) 2.88" (73.2) 2.05" (52.1) 3.21" (81.5) 2.80" (71.1) 90° with Male Metallic Metal Fitting Trade Size (md**) A B C D Ref. E Throat Dia. F A/C* A/F* A/C* A/F* ³⁄₈ (12) 1.31" (33.3) .59" (15.0) 1.20" (30.5) 1.06" (26.9) 1.44" (36.6) .60" (15.2) 1.13" (29.0) .99" (25.1) (16) 1.31" (33.3) .59" (15.0) 1.34" (34.0) 1.12" (28.4) 1.44" (36.6) .61" (15.5) 1.12" (28.0) 1.00" (25.4) (21) 1.44" (36.6) .59" (15.0) 1.55" (39.4) 1.45" (36.8) 1.63" (41.4) .83" (21.1) 1.48" (38.0) 1.29" (32.8) (27) 1.78 (45.2) .59" (15.0) 1.95" (49.5) 1.60" (40.6) 2.19" (55.6) 1.05" (26.7) 1.80" (46.0) 1.57" (39.9) (35) 1.97" (50.0) .63" (16.0) 2.39" (60.7) 2.06" (52.3) 2.50" (63.5) 1.36" (34.5) 2.32" (59.0) 2.02" (51.3) (41) 2.19" (55.6) .63" (16.0) 2.72" (69.1) 2.38" (60.5) 2.69" (68.3) 1.61" (40.9) 2.58" (66.0) 2.25" (57.2) (53) 2.53" (64.3) .66" (16.8) 3.08" (78.2) 2.87" (72.9) 3.25" (82.6) 2.05" (52.1) 3.14" (80.0) 2.75" (69.9) (63) 3.44" (87.4) 1.00" (25.4) 3.92" (99.6) 3.63" (92.2) 4.25" (108.0) 2.42" (61.5) 3.78" (96.0) 3.50" (88.9) (78) 3.75" (95.3) 1.00" (25.4) 4.70" (119.4) 4.31" (109.5) 4.87" (123.7) 3.01" (76.5) 4.64" (118.0) 4.30" (109.2) (103) 4.25" (108.0) 1.00" (25.4) 5.75" (146.1) 5.31" (134.9) 5.63" (143.0) 3.96" (100.6) 5.76" (146.0) 5.38" (136.7) Note: *A/C = Across Corners, A/F = Across Flats. **md = metric designator. Kellems® Wire Management Products Technical Information Metallic Liquidtight Fittings