DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

  • General Purpose Dielectric for Ceramic Capacitors
  • EIA Class II Dielectric
  • Temperature variation of capacitance is within ±15% from -55°C to +85°C
  • Well suited for decoupling and filtering applications
  • Available in High Capacitance values (up to 100μF) X5R Dielectric General Specifications PART NUMBER (see page 2 for complete part number explanation) GENERAL DESCRIPTION % /H9004 Capacitance -60 -40 -20 0 +20 +40 +60 +80 Temperature °C Temperature Coefficient -10 -15 -20 TYPICAL ELECTRICAL CHARACTERISTICS Insulation Resistance (Ohm-Farads) 1,000 10,000 100 Insulation Resistance vs Temperature 0 20 12040 60 80 Temperature °C 100 1210 Size (L" x W") Voltage 4 = 4V 6 = 6.3V Z = 10V Y = 16V 3 = 25V D = 35V 5 = 50V D Dielectric D = X5R 107 Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros M Capacitance Tolerance K = ±10% M = ±20% A Failure Rate A = N/A T Terminations T = Plated Ni and Sn Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk A Special Code A = Std. NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.

Specifications and Test Methods Parameter/Test X5R Specification Limits Measuring Conditions Operating Temperature Range -55ºC to +85ºC Temperature Cycle Chamber Capacitance Within specified tolerance ≤ 2.5% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10% Dissipation Factor ≤ 3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V ≤ 12.5% Max. for 16V DC rating and lower For Cap > 10 μF, 0.5Vrms @ 120Hz Contact Factory for DF by PN Insulation Resistance 10,000MΩ or 500MΩ - μF, Charge device with rated voltage for whichever is less 120 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Appearance No defects Deflection: 2mm Capacitance Test Time: 30 seconds Resistance to Variation ≤ ±12% Flexure Dissipation Meets Initial Values (As Above)Stresses Factor Insulation ≥ Initial Value x 0.3Resistance Solderability ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC with fresh solder for 5.0 ± 0.5 seconds Appearance No defects, <25% leaching of either end terminal Capacitance Variation ≤ ±7.5% Dip device in eutectic solder at 260ºC for 60Dissipation Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2Resistance to Factor hours before measuring electrical properties.Solder Heat Insulation Meets Initial Values (As Above)Resistance Dielectric Meets Initial Values (As Above)Strength Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes Capacitance Variation ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Dissipation Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutesThermal FactorShock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutesResistance Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after Strength 24 ± 2 hours at room temperature Appearance No visual defects Capacitance Variation ≤ ±12.5% Dissipation ≤ Initial Value x 2.0 (See Above)Load Life Factor Insulation ≥ Initial Value x 0.3 (See Above)Resistance Dielectric Meets Initial Values (As Above)Strength Appearance No visual defects Capacitance Variation ≤ ±12.5% Load Dissipation ≤ Initial Value x 2.0 (See Above)Humidity Factor Insulation ≥ Initial Value x 0.3 (See Above)Resistance Dielectric Meets Initial Values (As Above)Strength Charge device with 1.5X rated voltage in test chamber set at 85ºC ± 2ºC for 1000 hours (+48, -0). Note: Contact factory for *optional specification part numbers that are tested at < 1.5X rated voltage. Remove from test chamber and stabilize at room temperature for 24 ± 2 hours before measuring. Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Remove from chamber and stabilize at room temperature and humidity for 24 ± 2 hours before measuring. 1mm/sec 90 mm

PREFERRED SIZES ARE SHADED SIZE 01005 0201 0402 0603 0805 1206 1210 1812 Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only Reflow Only Packaging All Paper All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed All Embossed Cap 100 A (pF) 150 A

220 A C

330 A C

470 A C

680 A C

1000 B A A C

1500 A C

2200 A A C

3300 A C

4700 A C G

6800 A C G

Cap 0.010 B A C G (µF) 0.015 C G G G

0.022 A* CC GGG N

0.033 C G G G N

0.047 A* CC GGG N

0.068 C G G N

0.10 A* CCC G G N N

0.15 GN N

0.22 A* A* C* GG NN Q

0.33 GG N

0.47 C* C* GN Q Q X

0.68 GN

1.0 C * C* C* GGGJ * NN P * Q Q XXX

1.5

2.2 C* C* G* G* J* J* NNN QQ ZX

3.3 J* J* J* J* NN QQ

4.7 E* J* J* J* NN N * N * QQQQ QZ

47 *Q * Z*

100 Z* Z*

SIZE 01005 0201 0402 0603 0805 1206 1210 1812 = Under Development = *Optional Specifications – Contact factory L/H17010 /H17010 /H17010 /H17010 W /H17010/H17010 /H17010 /H17010 T t NOTE: Contact factory for non-specified capacitance values Letter ABCEGJ K M N PQXYZ PAPER EMBOSSED