Digital Temperature Sensor With a Two-Wire Interface datasheet (Rev. A)
Document overview
- Manufacturer or author: Texas Instruments, Incorporated [SLLS672,A]
- PDF pages: 20
Technical content
FEATURES
/C0068TWO ADDRESSES /C0068DIGITAL OUTPUT: Two-Wire Serial Interface /C0068RESOLUTION: 9- to 12-Bits, User-Selectable /C0068ACCURACY: ±2.0°C (max) from −25°C to +85°C ±3.0°C (max) from −40°C to +125°C /C0068LOW QUIESCENT CURRENT: 50µA, 0.1µA Standby /C0068NO POWER-UP SEQUENCE REQUIRED, I 2C PULLUPS CAN BE ENABLED PRIOR TO V+
APPLICATIONS
/C0068NOTEBOOK COMPUTERS /C0068COMPUTER PERIPHERAL THERMAL PROTECTION /C0068CELL PHONES /C0068BATTERY MANAGEMENT /C0068THERMOSTAT CONTROLS /C0068ENVIRONMENTAL MONITORING AND HVAC SDA SCL GND ALERT YZC LEAD−FREE
2 X 3 ARRAY
(TOP VIEW) Note: Pin A1 is marked with a for Pb−free (YZC) 1,65 mm 1,50 mm 1,15 mm 1,00 mm (Bump Side Down)
DESCRIPTION
The TMP106 is a two-wire, serial output temperature sensor available in a WCSP package. Requiring no external components, the TMP106 is capable of reading temperatures with a resolution of 0.0625°C. The TMP106 features a Two-Wire interface that is SMBus-compatible, with the TMP106 allowing up to two devices on one bus. The TMP106 also features an SMBus Alert function. The TMP106 is ideal for extended temperature measurement in a variety of communication, computer, consumer, environmental, industrial, and instrumentation applications. The TMP106 is specified for operation over a temperature range of −40°C to +125°C. Diode Temp . Sensor A/D Converter OSC Control Logic Serial Interface Config. and Temp. Register TMP106 Temperature SDA A1 GND SCL B1 B2 ALERT TMP106 SLLS672A − OCTOBER 2005 − REVISED JANUARY 2006 Digital Temperature Sensor with Two-Wire Interface Chip-Scale Package /C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046 www.ti.com Copyright 2005−2006, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners.
/C0084/C0077/C0080/C0049/C0048/C0054 SLLS672A − OCTOBER 2005 − REVISED JANUARY 2006 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) ESD Rating(3): (1)Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. (2)Input voltage rating applies to all TMP106 input voltages. (3)ESD testing has been tested to TI specifications JEDEC J−Std 020. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PACKAGE PART NUMBER SYMBOL Wafer chip-scale package (YZC) TMP106YZC F7 (1)For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. PIN ASSIGNMENTS SDA SCL GND ALERT WCSP−6 PACKAGE (TOP VIEW) Note: Pin 1 is determined by orienting the package marking as indicated in the diagram. (Bump Side Down)
/C0084/C0077/C0080/C0049/C0048/C0054 SLLS672A − OCTOBER 2005 − REVISED JANUARY 2006 www.ti.com
ELECTRICAL CHARACTERISTICS
At TA = −40°C to +125°C, and V+ = 2.7V to 5.5V, unless otherwise noted. PARAMETER CONDITION TMP106 UNITSPARAMETER CONDITION MIN TYP MAX UNITS TEMPERATURE INPUT Range −40 +125 °C Accuracy (Temperature Error) −25°C to +85°C ±0.5 ±2.0 °C vs Supply 0.2 ±0.5 °C/V Resolution(1) Selectable 0.0625 °C DIGITAL INPUT/OUTPUT Input Capacitance 3 pF Input Logic Levels: VIH 2.1 6.0 V VIL −0.5 0.8 V Leakage Input Current, IIN 0V ≤ VIN ≤ 6V 1 µA Input Voltage Hysteresis SCL and SDA Pins 250 mV Output Logic Levels: VOL SDA IOL = 3mA 0 0.15 0.4 V VOL ALERT IOL = 4mA 0 0.15 0.4 V Resolution Selectable 9 to 12 Bits Conversion Time 9-Bit 27.5 37.5 ms 10-Bit 55 75 ms 11-Bit 110 150 ms 12-Bit 220 300 ms Timeout Time 25 54 74 ms POWER SUPPLY Operating Range 2.7 5.5 V Quiescent Current IQ Serial Bus Inactive 50 85 µA Serial Bus Active, SCL Freq = 400kHz 100 µA Serial Bus Active, SCL Freq = 3.4MHz 410 µA Shutdown Current ISD Serial Bus Inactive 0.1 3 µA Serial Bus Active, SCL Freq = 400kHz 60 µA Serial Bus Active, SCL Freq = 3.4MHz 380 µA TEMPERATURE RANGE Specified Range −40 +125 °C Operating Range −55 +127 °C Thermal Resistance /C0113JA 240 °C/W (1)Specified for 12-bit resolution.
/C0084/C0077/C0080/C0049/C0048/C0054 SLLS672A − OCTOBER 2005 − REVISED JANUARY 2006 www.ti.com TYPICAL CHARACTERISTICS At TA = +25°C and V+ = 5.0V, unless otherwise noted. QUIESCENT CURRENT vs TEMPERATURE Temperature (/C0095C) −50 −25 0 25 50 75 100 125 IQ (µA) V+ = 2.7V Serial Bus Inactive V+ = 5V 300 250 200 150 100 CONVERSION TIME vs TEMPERATURE Temperature (/C0095C) Conversion Time (ms) −50 −25 0 25 50 75 100 125 V+ = 2.7V V +=5 V 12−bit resolution. 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.1 SHUTDOWN CURRENT vs TEMPERATURE Temperature (/C0095C) ISD (µA) −55 −35 −15 5 25 45 65 85 105 125 V +=2 . 8 V 2.0 1.5 1.0 0.5 0.0 −0.5 −1.0 −1.5 −2.0 TEMPERATURE ACCURACY vs TEMPERATURE Temperature Error (/C0095C) 3 typical units 12−bit resolution. Temperature (/C0095C) −55 −35 −15 5 25 45 65 85 105 125 500 450 400 350 300 250 200 150 100 QUIESCENT CURRENT WITH BUS ACTIVITY vs TEMPERATURE Frequency (Hz) 1k 10k 100k 1M 10M IQ (µA) 125/C0095C 25/C0095C −55/C0095C Hs MODE FAST MODE
Table 5. Temperature Data Format used with the unused LSBs set to zero. Configuration Register is all bits equal to 0.
1 OS R1 R0 F1 F0 POL TM SD
Table 6. Configuration Register Format Figure 3. Output Transfer Function Diagrams order, see the High and Low Limit Registers section. Table 7. Fault Settings of the TMP106
resolution and conversion time. Table 8. Resolution of the TMP106 LOW value for the same number of faults. returning the device to Comparator Mode (TM = 0). Both operational modes are represented in Figure 3. for the Temperature Register.
1 H11 H10 H9 H8 H7 H6 H5 H4
2 H3 H2 H1 H0 0 0 0 0
Table 9. Bytes 1 and 2 of THIGH Register
1 L11 L10 L9 L8 L7 L6 L5 L4
2 L3 L2 L1 L0 0 0 0 0
Table 10. Bytes 1 and 2 of TLOW Register configured for 9-bit resolution.
power dissipation associated with detection. Table 11. Address Pin and Slave Addresses for the START and STOP conditions. indicating whether a read or write operation is intended. bit HIGH to initiate the read command. by the next write operation. followed by the least-significant byte.
/C0084/C0077/C0080/C0049/C0048/C0054 SLLS672A − OCTOBER 2005 − REVISED JANUARY 2006 www.ti.com SLAVE MODE OPERATIONS The TMP106 can operate as a slave receiver or slave transmitter. Slave Receiver Mode: The first byte transmitted by the master is the slave address, with the R/W bit LOW. The TMP106 then acknowledges reception of a valid address. The next byte transmitted by the master is the Pointer Register. The TMP106 then acknowledges reception of the Pointer Register byte. The next byte or bytes are written to the register addressed by the Pointer Register. The TMP106 acknowledges reception of each data byte. The master may terminate data transfer by generating a START or STOP condition. Slave Transmitter Mode: The first byte is transmitted by the master and is the slave address, with the R/W bit HIGH. The slave acknowledges reception of a valid slave address. The next byte is transmitted by the slave and is the most significant byte of the register indicated by the Pointer Register. The master acknowledges reception of the data byte. The next byte transmitted by the slave is the least significant byte. The master acknowledges reception of the data byte. The master may terminate data transfer by generating a Not-Acknowledge on reception of any data byte, or generating a START or STOP condition. SMBus ALERT FUNCTION The TMP106 supports the SMBus Alert function. When the TMP106 is operating in Interrupt Mode (TM = 1), the ALERT pin of the TMP106 may be connected as an SMBus Alert signal. When a master senses that an ALERT condition is present on the ALERT line, the master sends an SMBus Alert command (00011001) on the bus. If the ALERT pin of the TMP106 is active, the devices will acknowledge the SMBus Alert command and respond by returning its slave address on the SDA line. The eighth bit (LSB) of the slave address byte will indicate if the temperature exceeding T HIGH or falling below TLOW caused the ALERT condition. This bit will be HIGH if the temperature is greater than or equal to THIGH . This bit will be LOW if the temperature is less than TLOW . Refer to Figure 7 for details of this sequence. If multiple devices on the bus respond to the SMBus Alert command, arbitration during the slave address portion of the SMBus Alert command will determine which device will clear its ALERT status. If the TMP106 wins the arbitration, its ALERT pin will become inactive at the completion of the SMBus Alert command. If the TMP106 loses the arbitration, its ALERT pin will remain active. GENERAL CALL The TMP106 responds to a Two-Wire General Call address (0000000) if the eighth bit is 0. The device will acknowledge the General Call address and respond to commands in the second byte. If the second byte is 00000100, the TMP106 will latch the status of the address pin, but will not reset. If the second byte is 00000110, the TMP106 will latch the status of the address pin and reset the internal registers to their power-up values. HIGH-SPEED MODE In order for the Two-Wire bus to operate at frequencies above 400kHz, the master device must issue an Hs-mode master code (00001XXX) as the first byte after a START condition to switch the bus to high-speed operation. The TMP106 will not acknowledge this byte, but will switch its input filters on SDA and SCL and its output filters on SDA to operate in Hs-mode, allowing transfers at up to 3.4MHz. After the Hs-mode master code has been issued, the master will transmit a Two-Wire slave address to initiate a data transfer operation. The bus will continue to operate in Hs-mode until a STOP condition occurs on the bus. Upon receiving the STOP condition, the TMP106 will switch the input and output filters back to fast-mode operation. TIMEOUT FUNCTION The TMP106 will reset the serial interface if either SCL or SDA are held LOW for 54ms (typ) between a START and STOP condition. The TMP106 will release the bus if it is pulled LOW and will wait for a START condition. To avoid activating the timeout function, it is necessary to maintain a communication speed of at least 1kHz for SCL operating frequency.
Figure 5. Two-Wire Timing Diagram for TMP106 Write Word Format
00 R / W 0 0000 0 P 1 P 0 …
00 A 0
00 A 0 R/W D7 D6 D5 D4 D3 D2 D1 D0
Figure 6. Two-Wire Timing Diagram for Read Word Format
Figure 7. Timing Diagram for SMBus ALERT
www.ti.com 23-May-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) TMP106YZCR Active Production DSBGA (YZC) | 6 3000 | LARGE T&R Yes SNAGCU Level-1-260C-UNLIM -40 to 125 F7 TMP106YZCR.B Active Production DSBGA (YZC) | 6 3000 | LARGE T&R Yes SNAGCU Level-1-260C-UNLIM -40 to 125 F7 TMP106YZCT Obsolete Production DSBGA (YZC) | 6 - - Call TI Call TI -40 to 125 F7 (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 22-Jan-2026 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION www.ti.com 22-Jan-2026 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TMP106YZCR DSBGA YZC 6 3000 220.0 220.0 35.0 Pack Materials-Page 2
www.ti.com PACKAGE OUTLINE C
0.625 MAX
0.35 0.15 TYP
0.25 TYP
6X 0.35 0.25 0.5 TYP
0.5 TYP
D 4219522/A 02/2015 DSBGA - 0.625 mm max heightYZC0006 DIE SIZE BALL GRID ARRAY NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. NanoFree TM package configuration. NanoFree Is a trademark of Texas Instruments. BALL A1 CORNER SEATING PLANE BALL TYP 0.08 C A
0.015 C A B
C B SCALE 9.000
www.ti.com EXAMPLE BOARD LAYOUT 6X ( ) 0.265 (0.5) TYP (0.5) TYP ( ) METAL 0.265 0.05 MAX SOLDER MASK OPENING METAL UNDER SOLDER MASK ( ) SOLDER MASK OPENING 0.265
0.05 MIN
DSBGA - 0.625 mm max heightYZC0006 DIE SIZE BALL GRID ARRAY NOTES: (continued) 4. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints. For more information, see Texas Instruments literature number SNVA009 (www.ti.com/lit/snva009). SYMM SYMM LAND PATTERN EXAMPLE SCALE:30X 1 2 A B C NON-SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DETAILS NOT TO SCALE SOLDER MASK DEFINED
www.ti.com EXAMPLE STENCIL DESIGN (0.5) TYP (0.5) TYP 6X ( 0.25) (R ) TYP 0.05 METAL TYP 4219522/A 02/2015 DSBGA - 0.625 mm max heightYZC0006 DIE SIZE BALL GRID ARRAY NOTES: (continued) 5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. SYMM SYMM SOLDER PASTE EXAMPLE BASED ON 0.1 mm THICK STENCIL SCALE:40X 1 2 A B C
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2026, Texas Instruments Incorporated Last updated 10/2025